Korg sampler, music workstation Media, 151, Floppy disk, Internal hard drive, external devices

→Select an effect other than 000: No Effect for “IFX1– 5” or “MFX 1, 2.”

Are the “IFX 1–5 Off,” “MFX1 Off,” or “MFX2 Off” (Global P0: Basic page) settings checked? ☞p.140

If you are in Combination, Sequencer, and Song Play, and master effects are not applied when you raise the “Send1” or “Send2” of the timbre/track, does “Return 1” or “Return 2” from the master effect need to be raised? ☞p.141 Alternatively, has “Send 1” or “Send 2” for each oscillator of the program used by the timbre/track been lowered? ☞p.140

The actual send level is determined by multiplying the send setting of each oscillator in the program with the send setting of the timbre/track.

Have you routed the output to an insert effect? ☞p.140, 141

MIDI

The TRITON STUDIO does not respond to incoming MIDI data

Are all MIDI cables connected correctly? ☞PG p.258

Is the MIDI data being received on the channel on which it is being transmitted? ☞PG p.259

The TRITON STUDIO does not respond correctly to incoming MIDI data

Are the Global P1: MIDI settings “Enable Program Change,” “Enable Bank Change,” “Enable Control Change,” and “Enable AfterTouch” each checked? ☞PG p.144

If you wish to receive MIDI exclusive messages, is the “Enable Exclusive” (Global P1: MIDI) item checked? ☞PG p.144

Does the TRITON STUDIO support the types of messages that are being sent to it? ☞PG p.259

Media

Floppy disk

Can’t format a floppy disk

Are you using a 3.5 inch 2HD or 2DD floppy disk?

Is the floppy disk inserted correctly?

Cover the write protect hole of the floppy disk, so that it is in the “write permit” position.

→Correctly insert a 3.5 inch 2HD or 2DD floppy disk (with its write protect hole covered) into the disk drive, and format it once again.

Can’s save/load data to/from a floppy disk

Is the floppy disk inserted correctly?

Is the floppy disk formatted?

Is the write protect hole of the floppy disk covered, so that it is in the “write permit” position?

→Correctly insert a 3.5 inch 2HD or 2DD floppy disk (with its write protect hole covered) into the disk drive, and perform the save or load operation once again.

Internal hard drive, external devices

SCSI-connected external drive is not recognized

Has the drive been formatted? ☞PG p.170

Is the external device connected correctly? ☞PG p.298

Is the terminator of the external device connected correctly? ☞PG p.298

The SCSI device ID settings of two or more drives may be conflicting.

→For details on setting the SCSI device ID, refer to the owner’s manual for your drive.

You may have turned on the power of the SCSI device after powering-on the TRITON STUDIO.

→Turn off the power of the SCSI device and of the TRITON STUDIO. Then turn on the power of the SCSI device, and wait at least ten seconds before powering-on the TRITON STUDIO.

Execute the page menu command “Scan SCSI device” (Disk, Media Information) to re-mount the SCSI device.

The TRITON STUDIO does not recognize when MO disk has been exchanged, and does not correctly display the media information after the exchange.

If you are able to switch the mode setting of your MO drive between PC/AT and Mac settings, please use PC/AT mode. For details on changing the mode of your drive, refer to the owner’s manual for your MO drive.

If your MO drive does not have a mode setting, or if the media exchange is not recognized even after you switch the mode, use the drive select button to select a different drive, and then re-select the MO drive.

“Error in writing to medium” occurs frequently when saving data to the internal hard drive or external device

Execute the page menu command “Check Medium” (Disk, Utility page) to detect and correct errors on the selected MS-DOS format media. ☞PG p.171

CD-R/RW

CD-R/RW drive is not recognized

If you are using the CDRW-1 option, was it installed correctly?

→Turn on the power of the TRITON STUDIO once again, and verify that the CDRW-1 is displayed in the startup screen. If it is not displayed, turn off the power, and re-install the drive correctly. ☞p.19

Appendices
Troubleshooting
Specifications	& options
MIDI	implementation chart
Index

151