Korg music workstation, sampler manual Overdub, Manual punch-in, Auto punch-in

2Set the “Recording Mode” to Over Write.

3In “Location,” specify the location at which you wish to begin recording.

4Press the SEQUENCER [REC/WRITE] key, and then press the SEQUENCER [START/STOP] key.

If the “Metronome Setup” is still set to the default set- tings, the metronome will sound for a two-measure pre-count, and then recording will begin.

Play the keyboard and move controllers such as the joystick to record your performance.

5When you finish playing, press the SEQUENCER [START/STOP] key.

Recording will end, and the location will return to the point at which you begin recording.

If you press the [PAUSE] key instead of the SEQUENCER [START/STOP] key, recording will pause. When you press the [PAUSE] once again, recording will resume. When you are finished, press the SEQUENCER [START/STOP] key to stop record- ing.

•Overdub

With this method, the newly recorded musical data is added to the existing data.

When you perform overdub recording on a previously- recorded track, the newly recorded data will be added to the previously-recorded data.

It is best to select this mode if you will be recording additional control data, recording a drum pattern, or recording the tempo in the master track. With this mode, data can be added without erasing the existing performance data.

1Use “Track Select” to select the track that you want to record.

2Set the “Recording Mode” to Over Dub.

3For the rest of the procedure, refer to steps 3–5of “Overwrite.”

•Manual punch-in

While the song is playing, you can press the SEQUENCER [REC/WRITE] key or a connected pedal switch at the desired location to start or stop recording. With this method, the musical data previously on the track is overwritten by the newly recorded data.

1Use “Track Select” to select the track that you want to record.

2Set the “Recording Mode” to Manual Punch In.

3In “Location,” specify a location several measures earlier than the point at which you wish to begin recording.

4Press the SEQUENCER [START/STOP] key. Playback will begin.

5At the point at which you wish to begin recording, press the SEQUENCER [REC/WRITE] key.

Recording will begin. Play the keyboard and operate controllers such as the joystick to record your perfor- mance.

6When you finish recording, press the SEQUENCER [REC/WRITE] key.

Recording will end (playback will continue).

Instead of pressing the SEQUENCER [REC/WRITE] key in steps 5 and 6, you can use a foot switch con- nected to the ASSIGNABLE SWITCH jack.

Set the Global P2: Controller page “Foot SW Assign” to Song Punch In/Out (☞p.125).

7Press the SEQUENCER [START/STOP] key.

Playback will stop, and you will return to the location that you specified in step 3.

•Auto punch-in

First you must specify the area that will be re-recorded. Then recording will occur automatically at the speci- fied area.

With this method, the musical data previously on the track is overwritten by the newly recorded data.

1Use “Track Select” to select the track that you want to record.

2Set the “Recording Mode” to Auto Punch In.

3In “M (Auto Punch In Start Measure), “M (Auto Punch In End Measure)” specify the area that you wish to record.

For example if you specify M005–M008, recording will occur only from measure 5 to measure 8.

4In “Location,” specify a location several measures earlier than the point at which you wish to begin recording.

5Press the SEQUENCER [REC/WRITE] key, and then press the SEQUENCER [START/STOP] key.

Playback will begin.

When you reach the starting location you specified in step 3, recording will begin. Play the keyboard and operate controllers such as the joystick to record your performance. When you reach the ending location you specified in step 3, recording will end. (Playback will continue.)

6Press the SEQUENCER [START/STOP] key.

Playback will stop, and you will return to the location you specified in step 4.

84