Mitsubishi Electronics DX-TL5000U instruction manual 114, Countermeasure Log number output

Warnings and CALL OUT output

Warnings and their appropriate countermeasures

#1 Options in the CALL OUT output column:

•Selectable: Selects to output CALL OUT signal or not on the menu screen.

•Fixed: Outputs CALL OUT signal from the CALL OUT terminal regardless of the menu setting.

•None: Does not output CALL OUT signal, but displays a warning on the screen.

•The warning display appears when the HELP button is pressed during “ALERT” is displayed on the screen. The contents of last 16 warnings are stored and can be displayed. The contents older than those are cleared and output of CALL OUT is cancelled. CALL OUT signal output can be stopped by pressing the E button or clicking “Clear Warning” while displaying the warning display.

					Cancelling				CALL OUT	Page
Warning Display		Countermeasure					Log number output
					the warning			#1
The remaining capacity of Normal Area		• Copy data as necessary.			Click "Clear		LOG1200		Selectable 61
in Main device has become less than **%.#2					Warning" or
The remaining capacity of Alarm Area					press the E		LOG1201
in Main device has become less than **%.#2					button.
The remaining capacity of LPA Area							LOG1202
in Main device has become less than **%.#2
The remaining capacity of Copy 2 disk							LOG7200
has become less than **%.#2
The remaining capacity of Normal Area		• When the warning is			Click "Clear		LOG1100#3		Selectable 82
in Main device has become 0%.		cancelled, the unit will start			Warning" or		LOG4100#4		None
The remaining capacity of Alarm Area		over-writing the oldest data			press the E		LOG1101#3		Selectable
in Main device has become 0%.		remaining in the hard disk			button.		LOG4101#4		None
The remaining capacity of LPA Area		drive.					LOG1102		Selectable
in Main device has become 0%.		• Copy data as necessary.
The remaining capacity of disc in Copy 1		• Replace media if necessary.			Click "Clear		LOG3100		None	44, 45
drive has become 0%.					Warning" or
The remaining capacity of disc in Copy 2					press the E		LOG7100		Selectable	44, 45
drive has become 0%.					button.
Copy data size error.		• Set the copy/restore range			Click "Clear		LOG3701#5		None	44, 45
Check the range of copy data or the disk		again.			Warning" or		LOG7701#6
		• Replace with new media.			press the E		LOG4701#4
space of copy media.					button.
Copy media error.		• Check media in recording			Click "Clear		LOG3702#5		None	44, 45
Cannot copy the data.		device. (Insert the media if			Warning" or		LOG7702#6
		there is none.)			press the E		LOG4702#4
Check the copy device.		• Check whether it is write-			button.
		protect by media. Cancel
		protection if it is protected.
		• After peripheral recording
		device and the unit power off a
		power supply, reboot in order
		of peripheral recording device
		and the unit.
		• After peripheral recording
		device and the unit power
		off a power supply, check a
		cable and termination
		(for SCSI device only).
No disk.		• Insert the disc.			Click "Clear		LOG3703#5		None	80
The drive has no disk or wrong type of disk.					Warning" or		LOG7703#6
					press the E		LOG4703#4
Put a proper disk into the drive.					button.
The remaining capacity of disc in Copy 1		• Replace the disc.			Click "Clear		LOG3704#5		None	44, 45
drive has become 0%.					Warning" or
Put a new disc into the drive.					press the E
The remaining capacity of disc in Copy 2					button.		LOG7704#6
drive has become 0%.
Put a new disc into the drive.
#2 : The value depends on the setting.	#7 : (The following numbers are in				)
#3 : Log number for Recording		01 : CH 1	02 : CH 2	03: CH 3		04 : CH 4	05 : CH 5	06 : CH 6
#4 : Log number for Restore		07 : CH 7	08 : CH 8	09 : CH 9		10 : CH 10 11 : CH 11		12 : CH 12
#5 : Log number for COPY 1		13 : CH 13	14 : CH 14 15 : CH 15			16 : CH 16
#6 : Log number for COPY 2

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

114