177 | Mitsubishi Electronics FR-A700, 700 Series specification

Instruction Processing Time

Instruction	Condition	Number	Processing
	(Device)	of Steps	Time (∝s)
OR<>		7	8.2

OR>		5	7.5
OR>		7	8.2
OR<=		5	7.5

OR<=		7	8.2
OR<		5	7.5
OR<		7	8.2

OR>=		5	7.6
OR>=		7	8.2
+		5	10.3

+P		5	10.7
+		7	10.3
+P		7	10.7

-		5	10.3
-P		5	10.7
-		7	10.4

-P		7	10.8
*		7	10.8
*P		7	11.3

/		7	11.3
/P		7	11.8

REMARKS

As inverter control is also performed actually, the scan time is approximately 40ms at 500 steps.

177

Image 182

Mitsubishi Electronics FR-A700, 700 Series specifications 177

Contents

Communication Sequence Programming Error Code ListPLC Function Paluse train input function PID control Inverter Status Monitoring, Special Registers for ControlAnalog I/O function Device Map Overview CC-Link I/O Specifications Buffer MemoryCC-Link Parameters Program Makeup Programming Languages Keyword Registration Counters CFunction List Bit Device Processing Method 155 How to Read the Error Code 172Basic Instructions 140 171 Using GX Developer for RS-485 Communication PLC Function Function Block Diagram PLC Function Specifications A700 Sequence Section Communication specifications System ConfigurationSystem configuration example Support GX Developer ver.8.0 or more GX Developer Setting Type Maker Usable main GX Developer functions Precautions for sequence program creationPrior to Sequence Program Creation Sequence program execution key Sequence program write Setting list of built-in PLC function parameter GX Developer Default Setting Range Usable device range Device Name Remarks Device Map1 I/O device map RAM Special relays Internal relay M device mapData register D device map M0 to M63 Device Map Special registers Name Description Map Inverter operation Input terminal D9205 For control D9206 Special registers D9207 PID Operation monitor Device Name Setting Data ExampleData that can be read at all times Unit Condition Data Alarm definition read program example Error No Error Name Details Operation mode setting read program example Data read timing chartOperation mode setting read D9140 Set frequency Eeprom D9142 Set frequency RAM D9141Set frequency RAM read program example Set frequency read Eeprom program example Data write timing chart Device Name Operation mode setting write program example Operation mode setting write D9143 Data are as followsWhen Pr =2, switching is performed as shown below Following program changes the set frequency RAM to 30Hz Set frequency RAM D9144Set frequency write RAM program example Following program changes the set frequency Eeprom to 10Hz Set frequency Eeprom D9145Set frequency write Eeprom program example Following program batch-clears the alarm history Alarm definition batch clear D9146Alarm definition batch clear program example All parameter clear program example Device No Setting Description DetailsParameter clear D9147 Following program clears all parameters Inverter operation status control D9148 Device No Name Data Access Enable ConditionInverter operation status control B15 B12B11 B8B7 B4B3 1 1 1 1 1 1 1 1 1 Invalid Parameter Inverter parameter access error D9150Inverter status D9151 Hffff is stored into D9150. Normal Inverter Parameter Read/Write Method Reading the inverter parameters Inverter parameter data read timing chart Writing the inverter parameters Inverter parameter data write timing chart User parameter read/write method Device Inverter Initial Setting Minimum SettingUser Area Read/Write Method Range Unit Analog input Device Terminal Name SettingAnalog I/O function Analog output Paluse train input function Parameter Name Initial Setting Description Value RangeDevice No Name Setting Description Range Selection Parameter Name Initial Value Setting Description RangePID control Device No Name Setting Description Range Setting Description Inverter Operation Lock Mode SettingName Initial Setting Minimum Setting Range Unit Memo Communication System configuration example Function block diagram CPU PLC CPU CC-Link Parameters CC-Link Extended Setting PrParameter Initial Setting Name CC-Link Description Number Remote register function can be extended CC-Link I/O Specifications Remote I/O Address Description Remote resisterData I/O image RAM, Eeprom Address Description Upper Bits Same as when Pr = 112 Refer to RWrn+7 Sixth monitor value RWwn+8 PLC function Station Buffer Memory Remote output signals Master module to inverterFR-A7NCBuffer Memory Address Station Buffer F2H Remote registers Pr.544=100 Master module to inverterFR-A7NC Station Buffer Memory Address Remote registers Pr.544=100 InverterFR-A7NC to master module Operation Processing Method of PLC Function Processing Method Scan TimeInstruction Format Numerical Values Usable in Sequence Program Overview Outline of Operation Processings Operation Processings of Built-in PLC function END processing RUN and Stop Operation Processings Program Makeup Ladder Blocks Relay symbolic language Ladder modeProgramming Languages Operation Processing Sequence Logic symbolic language List mode Logic symbolic language Operation Processing Method of PLC Function Operation Processing Method of Built-in PLC Function Control system is a refresh system What is refresh system?I/O Processing Method When Y1E turns on latest Response delay in refresh systemWhen Y1E turns on earliest Ladder example Scan Time Numerical Values Usable in Sequence Program Decimal Code Hexadecimal Code Binary Code BIN Binary Code DEC Decimal Code BIN Binary Code HEX HEX Decimal Description of devices Device List Inputs, Outputs X, Y 10 Inputs X, Outputs Y Inputs Outputs Y Internal Relays M 14 Internal Relay 15 Timing Chart Timers T5 100ms, 10ms and 100ms retentive timers Timing chart Timer processing method and accuracy 16 Timing Chart Timer timing method Counters C 18 Count Ladder Counting method Count processing in refresh system19 Counter Counting Method Maximum counting speed of counter Data Registers D Special Relays, Special Registers Special Application/Description Relay Function List Function Description 21 Timing Chart for RUN/STOP Using Remote RUN Contact Refer to the GX Developer manual for details Stop RUN/STOP Watchdog Timer Operation clog up monitor timer Self-diagnostic Function Error-time operation mode CPU Status Error Definition Operation Keyword Registration YES Instruction Format Program creation, it is fixed and cannot be Source SSpecify the numerical value to be used for Changed during program execution 20.1 1-bit processing 25 Digit Designation Setting Range for 16-bit InstructionBit Device Processing Method Digit designation processing 27 Ladder Examples and Processingse Hexadecimal number Numerical value setting method 1 Decimal numberHandling of Numerical Value Decimal Notation Hexadecimal Notation Operation Error Error processing Instructions List How to use the instruction listIndicates the symbol used in the ladder diagram Indicates Destination Operation result Symbol Execution Condition Symbol Processing 23.2 Sequence instruction 106 Basic instructions OR= ∗ P Application instructions , the instructions are described in the following format Description of the InstructionsDescription Sequence Instructions LD, LDI, AND, ANI, OR, ORI LD, LDI FunctionsExecution Conditions AND, ANI ANI , or , ORI Program ExamplesLD , LDI , Block a Block B ANB ORB Program Examples ANB, ORB 118 119 MPP MPSMRD 121 MPS , MRD , MPP Program using MPS, MRD and MPPProgram Example Output Instructions Bit device, timer, counter ... OUT OUT Instruction Operation Result Coil Contacts Contact OuttOutc Program that outputs to the output module Program ExamplesOUT RST Output Instructions Device set, reset ... SET, RSTSET Device Status Operations of SET and RST instructions SET and RST instructions are executed every scanSET , RST Program that resets the data register contents to Program that resets the 100ms retentive timer and counter PLS Digit Flag PLF Program that executes the PLS instruction when X9 turns onProgram that executes the PLF instruction when X9 turns off Shift Instructions Bit device shift ... SFT, Sftp SFT Program that shifts the Y7 B data when X8 turns onProgram Example Master Control Instructions Master control set, reset MC, MCR 134 Display in ladder mode MCR 136 End Instruction Sequence program end ... END Other Instructions No operation ... NOP NOP Contact short-circuit AND, ANI Comparison Operation Instructions SymbolBasic Instructions Instruction 141 S1 ≤ S2 S1 = S2S1 S2 S1 ≠ S2 S1 = S2 S1 ≤ S2 Program that compares the BIN value 100 and D3 data Program that compares the X0-F data and D3 dataProgram that compares the BCD value 100 and D3 data Program that compares the D0 and D3 data Arithmetic Operation Instructions 145 146 Is made at the highest bit b15 Addition/subtraction command 149 150 151 Operation Errors Data transfer instructions are designed to transfer data Data Transfer InstructionsData Transfer Instructions Bit data transfer ... MOV, Movp MOV Program that stores 155 into D8 in binary when X8 turns on Program that stores the input X0-B data into D8 Application instructions Logical Operation Instructions Wand Wand 157 158 WOR WOR P 161 Wxor Wxorp Wxor 164 Wxnr Wxnr Wxnr P 167 168 NEG Negp 170 Error Code List Definition and Cause Corrective Action How to Read the Error CodeError Error Name Code 173 Memo Appendix Appendix1 Instruction Processing Time Device 177 Revisions Print Date Manual Number Revision