Error-time operation mode | Mitsubishi Electronics 700 Series

Self-diagnostic Function

3.16.1 Error-time operation mode

The built-in PLC function allows you to set whether the sequence program operation will be stopped or continued at occurrence of an operation error.

Use the built-in PLC function parameter to set whether operation will be stopped or continued.

zDefault value of error-time operation mode

The following table indicates the default value (initial value) of the error-time operation mode and the status of the built-in PLC function.

Table 3.5 Error-time Operation Mode

			CPU Status
Error Definition		Operation	P.RUN	Special	registers	diagnostic
					Special	Self-
			LED	relays	for data	error No.
		Default value		relays
		Default value		turned on
					storage	(D9008)
	An error occurred in
	the sequence
	program, e.g. an
Operation	attempt was made to			M9010	D9010
Operation	make BCD	Continuation	Flicker	M9010	D9010	50
error	conversion of any			M9011	D9011
	conversion of any
	value outside the
	range 0 to 9999 (or 0
	to 99999999).

94

Image 99

Mitsubishi Electronics 700 Series, FR-A700 specifications Error-time operation mode, CPU Status Error Definition Operation

Contents

Error Code List PLC FunctionCommunication Sequence Programming Device Map Inverter Status Monitoring, Special Registers for ControlAnalog I/O function Paluse train input function PID control Program Makeup Programming Languages CC-Link I/O Specifications Buffer MemoryCC-Link Parameters Overview Bit Device Processing Method Counters CFunction List Keyword Registration 171 How to Read the Error Code 172Basic Instructions 140 155 PLC Function Using GX Developer for RS-485 Communication Function Block Diagram A700 Sequence Section PLC Function Specifications Support GX Developer ver.8.0 or more GX Developer Setting System ConfigurationSystem configuration example Communication specifications Maker Type Precautions for sequence program creation Prior to Sequence Program CreationUsable main GX Developer functions Sequence program execution key Sequence program write GX Developer Default Setting Range Usable device range Setting list of built-in PLC function parameter Device Map 1 I/O device mapDevice Name Remarks RAM M0 to M63 Internal relay M device mapData register D device map Special relays Device Map Name Description Special registers Map Inverter operation Input terminal D9205 For control D9206 Special registers D9207 PID Unit Condition Device Name Setting Data ExampleData that can be read at all times Operation monitor Data Error No Error Name Details Alarm definition read program example Data read timing chart Operation mode setting read D9140Operation mode setting read program example Set frequency read Eeprom program example Set frequency RAM D9141Set frequency RAM read program example Set frequency Eeprom D9142 Device Name Data write timing chart Operation mode setting write D9143 Data are as follows When Pr =2, switching is performed as shown belowOperation mode setting write program example Set frequency RAM D9144 Set frequency write RAM program exampleFollowing program changes the set frequency RAM to 30Hz Set frequency Eeprom D9145 Set frequency write Eeprom program exampleFollowing program changes the set frequency Eeprom to 10Hz Alarm definition batch clear D9146 Alarm definition batch clear program exampleFollowing program batch-clears the alarm history Following program clears all parameters Device No Setting Description DetailsParameter clear D9147 All parameter clear program example Device No Name Data Access Enable Condition Inverter operation status controlInverter operation status control D9148 B15 B12B11 B8B7 B4B3 1 1 1 1 1 1 1 1 1 Invalid Hffff is stored into D9150. Normal Inverter parameter access error D9150Inverter status D9151 Parameter Reading the inverter parameters Inverter Parameter Read/Write Method Inverter parameter data read timing chart Writing the inverter parameters Inverter parameter data write timing chart Range Unit Device Inverter Initial Setting Minimum SettingUser Area Read/Write Method User parameter read/write method Analog output Device Terminal Name SettingAnalog I/O function Analog input Selection Parameter Name Initial Setting Description Value RangeDevice No Name Setting Description Range Paluse train input function Setting Description Range PID controlParameter Name Initial Value Device No Name Setting Description Range Inverter Operation Lock Mode Setting Name Initial Setting Minimum Setting Range UnitSetting Description Memo Communication System configuration example CPU Function block diagram PLC CPU Remote register function can be extended CC-Link Extended Setting PrParameter Initial Setting Name CC-Link Description Number CC-Link Parameters Remote I/O CC-Link I/O Specifications Remote resister Data I/O imageAddress Description RAM, Eeprom Bits Address Description Upper Same as when Pr = 112 Refer to RWrn+7 Sixth monitor value RWwn+8 PLC function Address Remote output signals Master module to inverterFR-A7NCBuffer Memory Station Buffer Memory F2H Station Buffer Station Buffer Memory Address Remote registers Pr.544=100 Master module to inverterFR-A7NC Remote registers Pr.544=100 InverterFR-A7NC to master module Numerical Values Usable in Sequence Program Processing Method Scan TimeInstruction Format Operation Processing Method of PLC Function Outline of Operation Processings Overview END processing Operation Processings of Built-in PLC function Program Makeup RUN and Stop Operation Processings Relay symbolic language Ladder mode Programming LanguagesLadder Blocks Operation Processing Sequence Logic symbolic language Logic symbolic language List mode Operation Processing Method of Built-in PLC Function Operation Processing Method of PLC Function What is refresh system? I/O Processing MethodControl system is a refresh system Ladder example Response delay in refresh systemWhen Y1E turns on earliest When Y1E turns on latest Scan Time Decimal Code Hexadecimal Code Binary Code Numerical Values Usable in Sequence Program DEC Decimal Code BIN Binary Code BIN Binary Code HEX HEX Decimal Device List Description of devices 10 Inputs X, Outputs Y Inputs, Outputs X, Y Inputs Outputs Y 14 Internal Relay Internal Relays M Timing chart Timers T5 100ms, 10ms and 100ms retentive timers 15 Timing Chart 16 Timing Chart Timer processing method and accuracy Timer timing method 18 Count Ladder Counters C Count processing in refresh system 19 Counter Counting MethodCounting method Maximum counting speed of counter Data Registers D Special Relays, Special Registers Special Application/Description Relay Function Description Function List Refer to the GX Developer manual for details 21 Timing Chart for RUN/STOP Using Remote RUN Contact Stop RUN/STOP Watchdog Timer Operation clog up monitor timer Self-diagnostic Function CPU Status Error Definition Operation Error-time operation mode Keyword Registration YES Instruction Format Changed during program execution Source SSpecify the numerical value to be used for Program creation, it is fixed and cannot be Digit designation processing 25 Digit Designation Setting Range for 16-bit InstructionBit Device Processing Method 20.1 1-bit processing 27 Ladder Examples and Processingse Decimal Notation Hexadecimal Notation Numerical value setting method 1 Decimal numberHandling of Numerical Value Hexadecimal number Error processing Operation Error Indicates Destination Operation result How to use the instruction listIndicates the symbol used in the ladder diagram Instructions List Symbol Execution Condition 23.2 Sequence instruction Symbol Processing 106 OR= Basic instructions ∗ P Application instructions Description of the Instructions Description, the instructions are described in the following format LD, LDI, AND, ANI, OR, ORI Sequence Instructions AND, ANI FunctionsExecution Conditions LD, LDI Program Examples LD , LDI ,ANI , or , ORI Block a Block B ORB ANB Program Examples ANB, ORB 118 119 MPS MRDMPP 121 Program using MPS, MRD and MPP Program ExampleMPS , MRD , MPP OUT Instruction Operation Result Coil Contacts Output Instructions Bit device, timer, counter ... OUT Outt OutcContact Program Examples OUTProgram that outputs to the output module Device Status Output Instructions Device set, reset ... SET, RSTSET RST SET and RST instructions are executed every scan SET , RSTOperations of SET and RST instructions Program that resets the 100ms retentive timer and counter Program that resets the data register contents to Digit Flag PLS Program that executes the PLS instruction when X9 turns on Program that executes the PLF instruction when X9 turns offPLF Shift Instructions Bit device shift ... SFT, Sftp Program that shifts the Y7 B data when X8 turns on Program ExampleSFT MC, MCR Master Control Instructions Master control set, reset 134 MCR Display in ladder mode 136 End Instruction Sequence program end ... END NOP Other Instructions No operation ... NOP Contact short-circuit AND, ANI Instruction SymbolBasic Instructions Comparison Operation Instructions 141 S1 ≠ S2 S1 = S2 S1 ≤ S2 S1 = S2S1 S2 S1 ≤ S2 Program that compares the D0 and D3 data Program that compares the X0-F data and D3 dataProgram that compares the BCD value 100 and D3 data Program that compares the BIN value 100 and D3 data Arithmetic Operation Instructions 145 146 Is made at the highest bit b15 Addition/subtraction command 149 150 151 Operation Errors MOV Data Transfer InstructionsData Transfer Instructions Bit data transfer ... MOV, Movp Data transfer instructions are designed to transfer data Program that stores the input X0-B data into D8 Program that stores 155 into D8 in binary when X8 turns on Logical Operation Instructions Application instructions Wand Wand 157 158 WOR WOR P 161 Wxor Wxorp Wxor 164 Wxnr Wxnr P Wxnr 167 168 Negp NEG 170 Error Code List How to Read the Error Code Error Error Name CodeDefinition and Cause Corrective Action 173 Memo Appendix Device Appendix1 Instruction Processing Time 177 Print Date Manual Number Revision Revisions