Manuals / Onkyo / Home Audio / Stereo Receiver

Onkyo DTR-7.9 Setting the Zone2 Out, Fixed, Variable, Zone 2—Continued, The “Zone2” menu appears

Models: DTR-7.9

1 140

Download 140 pages 5.52 Kb

Page 117

Setting the Zone2 Out

Zone 2—Continued

Setting the Zone2 Out

If you’ve connected your Zone 2 speakers to an amp with no volume control, set the “Zone2 Out” setting, respec- tively, to “Variable” so that you can set the zone’s vol- ume, balance, and tone on the AV receiver.

	1	Press the [Receiver] button fol-
		Press the [Receiver] button fol-
	Remote	lowed by the [Setup] button.
	Remote	The main menu appears onscreen.
	controller	The main menu appears onscreen.
		If the main menu doesn’t appear, make
		sure the appropriate external input is
		selected on your TV.

2 Use the Up and Down [q]/[w] but- tons to select “7. Hardware Setup”, and then press [Enter]. The “Hardware Setup” menu appears.

7. Hardware Setup

1. Remote Control

2.Zone2

3.Tuner

4.Analog Multich

5.HDMI

6.Network

3	Use the Up and Down [q]/[w] but-
	tons to select “2. Zone2”, and
	then press [Enter].
	The “Zone2” menu appears.
	7–2. Zone2
	Powered Zone2	Not Act
	Zone2 Out	Fixed

4 Use the Up and Down [q]/[w] but- tons to select “Zone2 Out”, and use the Left and Right [e]/[r] buttons to select:

Fixed:

The Zone 2 volume must be set on the amp in that zone.

Variable:

The Zone 2 volume can be set on the AV receiver.

5	Press the [Setup] button.
	Press the [Setup] button.
	The setup menu closes.

Note:

This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button.

117

Image 117

Onkyo DTR-7.9 Setting the Zone2 Out, Fixed, Variable, Zone 2—Continued, The “Zone2” menu appears, The setup menu closes

Contents

AV Receiver DTR-7.9AVIS Important Safety Instructions4.Power Precautions5.Preventing Hearing Loss Caution 6.Batteries and Heat Exposure WarningRemote controller & two batteries AA/R6 Supplied AccessoriesSpeaker setup microphone Indoor FM antenna AM loop antenna Power cordFirst Time Setup ContentsUsing the Listening Modes Advanced SetupAmplifier FeaturesProcessing ConnectionsFront & Rear Panels Front & Rear Panels—Continued 9 bk bl DisplayFront & Rear Panels—Continued 9bk blbm bn bo bp bq br aCOMPONENT VIDEO IN 1, 2 and Front & Rear Panels—ContinuedFront & Rear Panels—Continued uu REMOTE CONTROLtPRE OUT: ZONE 2 L/R vIR IN A/B and OUTInstalling the Batteries Remote ControllerAiming the Remote Controller NotesAdjusts the display brightness Remote Controller-Continued6bm bn Controlling the AV ReceiverEnjoying Home Theater About Home TheaterConnecting Your Speakers Connecting the AV ReceiverSpeaker Configuration Using Dipole SpeakersConnecting the AV Receiver—Continued Speaker Connection PrecautionsConnecting the Speaker Cables Bi-ampingthe Front Speakers Bi-ampingSpeaker HookupConnecting the AV Receiver—Continued Connecting the AM Loop Antenna Connecting AntennaConnecting the Indoor FM Antenna Connecting the AV Receiver—ContinuedConnecting an Outdoor AM Antenna Connecting an Outdoor FM AntennaConnecting the AV Receiver-Continued Using a TV/FM Antenna SplitterAV Connection Color Coding About AV ConnectionsOptical Digital Jacks AV Cables & JacksWhich Connections Should I Use? Connecting Both Audio & VideoVideo Connection Formats Connecting the AV Receiver—ContinuedVideo Signal Flow and the Resolution Setting Audio Connection FormatsConnecting the AV Receiver—Continued Connecting a TV or Projector HintConnecting the AV Receiver—Continued Connecting a DVD Player b C B cConnecting the AV Receiver—Continued Connecting the AV Receiver—Continued Hooking Up the Multichannel DVD Input7.1 ch 5.1 chConnecting a VCR or DVD Recorder for Playback Connecting the AV Receiver-ContinuedHint B A a Connecting a VCR or DVD Recorder for RecordingConnecting the AV Receiver—Continued NotesConnecting the AV Receiver—Continued C b BHint Satellite, cable, set-topbox, etcConnecting a Game Console C B b a AConnecting the AV Receiver—Continued Connecting the AV Receiver—Continued Connecting a Camcorder or Other DeviceAbout HDMI Connecting Components with HDMISupported Audio Formats About Copyright ProtectionConnecting the AV Receiver—Continued Making HDMI ConnectionsVideo Signals Audio SignalsConnecting the AV Receiver—Continued Connecting a CD Player or TurntableStep Turntable MM with no Phono Preamp Built-inCassette, CDR, MD, etc Connecting the AV Receiver—ContinuedConnecting the AV Receiver-Continued Connecting a Power AmplifierPower amplifier Powered subwooferConnecting the AV Receiver—Continued Connecting an RI DockIf Your iPod Supports Video If Your iPod Doesn’t Support VideoConnecting the Power Cord Connecting Integra/Onkyo u ComponentsConnecting the AV Receiver—Continued NotesTurning On the AV Receiver Turning On and StandbySmooth Operation in a Few Easy Steps Monitor Setup First Time SetupPress the Setup button 1 2-42, 31,Using the Onscreen Setup Menus First Time Setup—ContinuedIf the main menu doesn’t appear, make SubmenusHDMI Input Setup Video Input SetupThe setup menu closes The “HDMI Input” menu appearsThe “Component Video Input” menu Component Video Setupappears First Time Setup-ContinuedThe “Digital Audio Input” menu Digital Input SetupExamples First Time Setup—ContinuedThe “Speaker Settings” menu appears Speaker Settings• Powered Zone2 cannot be used if Normal: Select this if you’ve conThe “OSD Setup” menu appears TV Format Setup not North American modelsFirst Time Setup—Continued The setup menu closesThe “Tuner” menu appears AM Frequency Step Setup not North American modelsFirst Time Setup—Continued The setup menu closesChanging the Input Display iPod photoFirst Time Setup—Continued Using Audyssey MultEQ Automatic Speaker Setup Audyssey MultEQ1 2, 3-8 Measurement PositionsFirst Time Setup—Continued 3 4 5Place the speaker setup micro Setup Mic jack6 7 8 CancelNext Finish CalculateFirst Time Setup-Continued Error MessagesSpeaker Detect Error Writing ErrorChanging the Speaker Settings Manually Using a Powered SubwooferFirst Time Setup—Continued Selecting the Input Source Basic OperationsAdjusting the Bass & Treble Using the Multichannel DVD InputSetting the Display Brightness Basic Operations—ContinuedUsing Headphones Using the Sleep TimerMuting the AV receiver Basic Operations—ContinuedTuning into Radio Stations Using the TunerTuning into weak FM stereo stations Listening to the RadioDeleting Presets Selecting PresetsThe preset number flashes preset number stops flashingAbout XM Radio Connecting the XM Mini-Tunerand Home DockXM Ready Legal XM Ready SubscriptionSelecting XM Satellite Radio Setting the Satellite Radio ModeXM/SIRIUS Listening to the Radio—Continuedon the AV receiver by using its Tuner This procedure can also be performedbutton, and Tuning Mode button Signing Up for XM Satellite RadioCategory Search Mode Listening to the Radio—ContinuedDisplaying XM Radio Information Presetting XM ChannelsThe preset number flashes Listening to the Radio—ContinuedPositioning the XM Mini-TunerSystem The best signal is achieved when theThe main menu appears onscreen The Tuner screen appearsUPGRADE XM TUNER NO SIGNALXM Radio Messages CHECK ANTENNAWhat is SIRIUS Satellite Radio? Setting Up the SiriusConnect Home TunerImportant SIRIUS Satellite Radio Information A warning against reverse engineeringSetting the Satellite Radio Mode Positioning the AntennaListening to the Radio—Continued The main menu appears onscreenSigning Up for SIRIUS Satellite Radio Selecting SIRIUS Satellite RadioSelecting SIRIUS Satellite Radio Channels Listening to the Radio—Continuedbutton, and Tuning Mode button This procedure can also be performedListening to the Radio—Continued Category Search ModeThe channel is stored and the preset Presetting SIRIUS Channelsnumber stops flashing favorite SIRIUS Satellite Radio chanParental Lock The “Tuner” screen appearsListening to the Radio—Continued Changing the PIN Number When Enter is pressed, the confirmaThe number, name, and status of the currently selected channel is displayedDisplaying SIRIUS Satellite Radio Information 5 6 7Press the Setup button Listening to the Radio-ContinuedListening to the Radio—Continued Positioning the SiriusConnect Home antennaThe main menu appears onscreen The “Tuner” screen appearsSUB UPDATED ANTENNA ERRORSIRIUS Satellite Radio Messages ACQUIRINGRDS Program Types PTY Using RDS not North American modelListening to the Radio-Continued NotesDisplaying Radio Text RT 1 3,Finding Stations by Type PTY Listening to Traffic News TPAV Recording RecordingRecording Separate AV Sources If you select another input source durSelecting with the Remote Controller Using the Listening ModesSelecting Listening Modes Selecting on the AV receiverUsing the Listening Modes—Continued Listening Modes Available for Each Source FormatAnalog and PCM Sources Using the Listening Modes—Continued Dolby Digital, and Dolby Digital Plus Sources4. Available only when using surround speakers 3. Cannot be selected with some source formatsUsing the Listening Modes—Continued DTS SourcesUsing the Listening Modes—Continued TrueHD Sources3. Available only when using surround speakers 2. Cannot be selected with some source formatsUsing the Listening Modes-Continued DTS-HDSourcesUsing the Listening Modes—Continued DTS Express and DSD Sources4. Available only when using surround speakers HintUsing the Listening Modes—Continued About the Listening ModesButton ButtonButton Using the Listening Modes—ContinuedButton ButtonUsing the Listening Modes—Continued Onkyo Original DSP ModesButton ButtonOnscreen Setup Menus Advanced Setup1. Input Assign 2. Speaker Setup 3. Audio Adjust 4. Source Setup 5. Listening Mode PresetSpeaker Setup Advanced Setup—ContinuedSpeaker Settings 1 2 3If no center speaker is connected, select If the “Front” setting in step 5 is set to“None” anything other than “Full Band”, “FullDouble Bass Low-PassFilter for the LFE ChannelOff THX Advanced Setup—Continued3-73, 42, Speaker DistanceAdvanced Setup—Continued Speaker Level Calibration 1 2-52, 31,Advanced Setup—Continued Notes1 2-7 4 2 Equalizer SettingAudyssey ManualNotes:3 THX Audio SetupAdvanced Setup—Continued The setup menu closes4 5 6 > 4ft > 1.2m default< 1ft < 0.3m 1ft – 4 ft 0.3 m – 1.2 mMultiplex/Mono Settings Audio Adjust FunctionsPLIIx/Neo 6 Music Mode Settings Advanced Setup—ContinuedT-D Theater-DimensionalListening Setting Dolby EX Input Signal SettingDSD Setting LFE Level SettingsTone Control Settings Adjust Using the Audio ButtonLate Night Function Re-EQFunctionMusic Optimizer Audyssey Dynamic EQTMSpeaker Levels A/V SyncAssigning Listening Modes to Input SourcesAdvanced Setup—Continued IntelliVolume Source SetupAdvanced Setup—Continued The setup menu closesTo correct a character Name EditAdvanced Setup—Continued A/V SyncAdvanced Setup—Continued Picture AdjustDefault Picture ModeVolume Setup Miscellaneous Volume/OSD SetupAdvanced Setup—Continued The setup menu closes12V Trigger A/B/C Setup OSD SetupAdvanced Setup—Continued Zone2 Maximum VolumeRemote Control Hardware SetupChanging the Remote Controller’s ID ZoneHDMI Analog Multich480p 480/576p Normal Full Zoom Wide ZoomFilm Mode Advanced Setup—ContinuedAudio TV Out Lip SyncAdvanced Setup—Continued NetworkNotes NotesThe “Lock Setup” menu appears Lock SetupLocked UnlockedDigital Input Signal Formats Automatic Audio Input Selection SetupThe current setting is displayed Auto defaultConnecting Your Zone 2 Speakers to an Amp in Zone Connecting ZoneZone HookupZone 2 Video Outputs Zone 2—ContinuedHookup Zone 2—Continued Setting the Powered ZoneThe “Zone2” menu appears Not ActFixed Setting the Zone2 OutVariable The setup menu closesControlling Zone 2 with the Remote Controller Using ZoneZone 2 turns on, the Zone 2 indicator Controlling Zone 2 from the AV receiverAdjusting the Tone and Balance of Zone Adjusting the Volume for ZoneMuting Zones ble from –10dB to +10 dB in 2 dBMain/Zone2 Using the 12V TriggersZone 2—Continued HookupUsing a Multiroom Kit with Zone Using a Multiroom Kit with a CabinetUsing a Multiroom Kit with Other Components Zone 2—ContinuedEntering Remote Control Codes Preprogrammed Remote Control CodesControlling Other Components The codes are organized by categoryResetting the Remote Controller Resetting Remote Mode Buttonsindicating that the remote controller has been reset78 9 bq Controlling a TVControlling Other Components-Continued 5bq 6 7br bs 8 9bt bkck bl cl Controlling a DVD Player or DVD RecorderControlling Other Components—Continued Page Page aOn/Standby button Controlling an RI Dock When Using an RI DockUsed with the repeat function Turns on the backlight for 30 secondsControlling a Cassette Recorder 1 6 7Controlling Other Components—Continued aOn/Standby buttonLearning Commands Controlling Other Components—ContinuedNotes Making Macros Using MacrosRunning Macros Deleting MacrosAmplifier Section SpecificationsVideo Section Tuner SectionPower Can’t turn on the AV receiver TroubleshootingAudio There’s no sound, or it’s very quiet Only the front speakers produce soundTroubleshooting—Continued Remote Controller Troubleshooting—ContinuedThe remote controller doesn’t work The onscreen menus don’t appearVideo ATT:OFF: default Video AttenuationTroubleshooting—Continued Important Note Regarding Video Playback Troubleshooting—ContinuedNTSC Video Resolution Chart2 9 3 4 4 7 4 5 A