Panasonic PT-DS12KU, PT-DW11KU, PT-DZ10KU, PT-DZ13KU [STARTUP INPUT SELECT], Note, Press, [COMMAND], [COMMAND], Description, [LAST USED], [LAMP SELECT], Detailed settings of, 10) Press the <ENTER> button

Chapter 4 Settings — [PROJECTOR SETUP] menu

[COMMAND]	Detailed settings of	Description
	[COMMAND]
	[VIDEO]	Switches the input to VIDEO.
	[RGB1]	Switches the input to RGB1.
	[RGB2]	Switches the input to RGB2.
	[DVI‑D]	Switches the input to DVI‑D.
[INPUT]	[HDMI]	Switches the input to HDMI.
		(PT‑DZ13KU, PT‑DS12KU)
	[SDI1]*1	Switches the input to SDI1.
		(PT‑DZ10KU)
		Switches the input to SDI.
	[SDI2]*2	Switches the input to SDI2.
	[DUAL]	Turns on two lamps.
[LAMP SELECT]	[SINGLE]	Turns on one lamp. (The lamp with shorter runtime will
		automatically light.)
	[HIGH]*3	Sets the lamp brightness to high luminance.
	[MIDDLE]*3	Sets the lamp brightness to slightly lower luminance compared to
[LAMP POWER]		[HIGH].
	[NORMAL]*4	Sets the lamp brightness to high luminance.
	[ECO]	Sets the lamp brightness to low luminance.
	[OFF]	P IN P function is not used.
[P IN P]	[USER1]	Lays out the sub-screen with the settings of [USER1].
	[USER2]	Lays out the sub-screen with the settings of [USER2].
	[USER3]	Lays out the sub-screen with the settings of [USER3].

*1 Only for PT‑DZ13KU, PT‑DS12KU, PT‑DZ10KU

*2 Only for PT‑DZ13KU, PT‑DS12KU

*3 Only for PT‑DZ13KU, PT‑DS12KU, PT‑DW11KU

*4 Only for PT‑DZ10KU

10) Press the <ENTER> button.

ff The [COMMAND] detailed screen is displayed.

11) Press as to select a [COMMAND].

ff For [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time you press qw.

12) Press the <ENTER> button.

ff The command is fixed and n is displayed at the left of the selected command.

ff After the command is fixed, press the <MENU> button to close the detailed setting screen.

13)Press asqw to select [STORE], and press the <ENTER> button.

Note

ff If you attempt to register the setting that would make the lamp turn on for a short time, an error message will be displayed on the screen. Set the time and command again.

ff To delete a command already set, press the <DEFAULT> button on the Step 5) screen, or select [DELETE] on the Step 6) screen and press the <ENTER> button.

ff If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command number.

ff The operating time will be the local time. (x page 121)

ff If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in [SCHEDULE] is executed, the command set with this function may not be executed.

[STARTUP INPUT SELECT]

Set the input when the projector is switched on to start projection.

1)Press as to select [STARTUP INPUT SELECT].

2)Press qw to switch the item.

ff The items will switch each time you press the button.

[LAST USED]	Keeps the input selected last.
[VIDEO]	Sets the input to VIDEO.
[RGB1]	Sets the input to RGB1.
[RGB2]	Sets the input to RGB2.
[DVI‑D]	Sets the input to DVI‑D.

ENGLISH - 117