Paradyne HOTWIRE 7986 guide

Standards Compliance for SNMP Traps

SNMP Trap	Description	Possible Cause

enterpriseTestStop(105)	All tests have been halted.	All tests have been halted on
		an interface.

enterpriseFallback	The LTU was able to
AutoRateClear(113)	resynch to the last known
	rate after the
	enterpriseFallback
	AutoRate(13) was reported.

There are no variable-bindings for enterpriseDeviceFail, enterprisePrimary ClockFail. enterpriseSecondaryClockFail, enterprisePrimaryClockFailClear, enterpriseSecondaryClockFailClear, and enterpriseConfigChange. The variable-binding for enterpriseSelfTestFail is devSelfTestResults.

The following list describes the conditions that define enterpriseFallbackAutoRate and enterpriseFallbackAutoRateClear:

enterpriseFallbackAutoRate Variable-Bindings

HifIndex (RFC 1573)

This object provides the index into the ifTable and potentially into tables in other MIBs. The values of ifIndex are the same for all models, although not all indexes are supported for each model.

The ifIndex included with the trap consists of:

±1 COM Port

±2 HDSL E1 Interface, Port 1

±6 G.703 Interface, Port 1

HifAdminStatus (RFC 1573)

This object specifies the operational state of the interface:

±up(1)

HDSL Network: DSL link is established.

G.703: No alarm condition exists.

±down(2)

HDSL Network: DSL link is not established.

G.703: An alarm condition exists.

±testing(3)

A test is active on the interface.

HifOperStatus (RFC 1573)

This object contains the same value as ifAdminStatus.

HifType (RFC 1573)

This object is the type of interface:

±e1(19)

Used for the G.703 E1 interface.

B-4

September 1998

7986-A2-GB20-00

Image 104

Paradyne HOTWIRE 7986 manual EnterpriseFallbackAutoRate Variable-Bindings

Contents

HOTWIRE Model Hdsl Standalone Termination Unit Copyright E 1998 Paradyne Corporation All rights reserved Important Safety Instructions EMI Warnings Contents Initial Startup and Configuration Messages and Troubleshooting Standards Compliance for Snmp Traps Document Summary About This GuideDocument Purpose and Intended Audience Product-Related Documents About the Model 7986 Standalone Termination Unit Hdsl Overview Hotwire 7986 Termination Unit Features Network Configuration CO Site Front Panel LED Status Indicators Rear Panel Interface Connections MIB Support Network About the Model 7986 Standalone Termination Unit Communication Port Settings Using the Asynchronous Terminal InterfaceUser Interface Access Login Initiating an ATI Session Select ScreenArea Function Main Screen Work Areas InputKeys Field Value Choices Messages Press Navigating the ScreensKeyboard Keys Screen Function Keys For the screen function Select Press Enter to Switching Between Screen Work Areas Example Ending an ATI Session Using the Asynchronous Terminal Interface Initial Startup and Configuration Overview Connecting Power to the Unit Optional Power SourcesConnecting the Unit to an Optional External DC Power Source +24 Vdc Power Supply Pinouts Connecting to the Network Connecting to a System Terminal Identity Entering Identity InformationMain Menu → Control → Change Choosing a Configuration Mode Configuring the Unit Using the Configuration MenusConfiguration Options Configuration Option Area Configuration Option Set Configuring the Unit Using the Internal Switches Handling Precautions for STATIC-SENSITIVE Devices Switchpack Locations Switchpack S1 & S2 Switchpack Definitions Switchpack S1 Definitions Switch # Allows you to Switchpack S2 Definitions Switch # Allows you to OFF = Autorate DisabledAll OFF = OFF = Current Firmware Accessing and Displaying Configuration Options Main Menu → Configuration Load Configuration FromLoad Configuration from If you select Then Configuration Edit/Display Main Menu → Configuration → Current ConfigurationMain Menu → Configuration → Default Factory Select To Access To Configure Configuring AutoRate Main Menu → Configuration → Network Payload Rate Payload Rate Time Rate kbps KbpsKbps Slots Time Configuration Loader Configuration LoaderMain Menu → Configuration → Configuration Loader Completed successfully Saving Configuration Options Save Configuration Download Code Main Menu → Control → Download CodeDownload Code DSL Initial Startup and Configuration Monitoring the Unit What to Monitor System and Test Status Health and Status SELF-TEST Results Viewing System and Test StatusMain Menu → Status → System and Test Status Health and Status Yyyyyyyy Call your service Self-Test Results Test Status Test Status Messages Meaning Network Error Statistics Viewing Network Error StatisticsMain Menu → Status → Performance → Network Error Statistics This Field Contains Viewing Network Performance Statistics This Field Contains Viewing G.703 Performance Statistics Performance Statistics This Field Contains General Viewing Model 7986 Standalone Termination Unit LEDsMain Menu → Status → Display LEDs LED is Indicating Model 7986 Standalone Termination Unit LEDsType Testing Accessing the Test MenuMain Menu → Test Network & G.703 Tests Running Network TestsMain Menu → Test → Network & G.703 Tests Line Loopback Repeater Loopback DTE Loopback Send Remote Line Loopback Send and Monitor Device Tests Lamp TestMain Menu → Test → Device Tests Device Tests Ending an Active Test Testing Messages and Troubleshooting Configuring Snmp Traps Snmp Traps Options Device Messages Device Messages 1 What Message Indicates What To Do Device Messages 2 What Message Indicates What To Do 127 Troubleshooting Troubleshooting 1 Symptom Possible Cause Solutions Troubleshooting 2 Symptom Possible Cause Solutions Tables ATI Access LevelsSecurity Login Entry Creating a LoginAdminister Logins On the Login Entry screen, for Enter Deleting a Login Resetting the Termination Units COM Port or Factory Defaults If entering yes to prompt Then Security IP Addressing Selecting an IP Addressing Scheme IP Addressing Example Peer IP Address Assignments Configuration Option Tables Configuration Options in , Initial Startup and Configuration Table A-1. Network Interface Options 1 Main Menu → Configuration → Current Configuration →Network Interface Options Menu Table A-1. Network Interface Options 2 Circuit Identifier Main Menu → Configuration → Load Configuration From → G Interface Options MenuTable A-2. G.703 Interface Options 1 Port Status Table A-2. G.703 Interface Options 2 Line FramingTime Slot Primary Clock Source Main Menu → Configuration → Load Configuration From → DSL ModeTest Timeout System Options Menu Test Duration min Line Termination Port Type Possible Settings Asynchronous, Synchronous Communication PortTable A-4. Communication Port Options 1 Port Use Table A-4. Communication Port Options 2 Login Required Asynchronous mode only Port Access Level Asynchronous mode onlyInactivity Timeout Asynchronous mode only Disconnect Time Minutes Asynchronous mode only Telnet Session Options Management and Communication Options MenuTelnet Session Options Table A-5. Telnet Session Options PPP Communication Protocol OptionsCommunication Protocol Options Node IP Address Possible Settings 000.000.000.000 ± Node Subnet Mask Possible Settings 000.000.000.000 ±Default Network Destination Table A-6. Communication Protocol Options 1 Table A-6. Communication Protocol Options 2 Communication Port Link Protocol Snmp Traps Options Table A-7. Snmp Traps Options 1 Snmp TrapsNumber of Trap Managers NMS n Destination Link Traps Possible Settings Disable, Up, Down, Both Table A-7. Snmp Traps Options 2Enterprise Specific Traps Link Trap Interfaces AuthenticationFailure Standards Compliance for Snmp TrapsSnmp Traps WarmStart LinkUp and linkDown LinkUp/Down Variable-Bindings Enterprise-Specific Traps EnterpriseFallbackAutoRate Variable-Bindings Hdsl Standards Compliance for Snmp Traps Cables and Pin Assignments E1 Network Interface DSL Network Interface Cable Table C-2. DSL Network Interface ConnectorSignal Pin Number Table C-3. COM Port Interface Connector Signal Pin Number COM Port Interface Cable Table C-4. DC Power Connector Signal Pin Number Power Input ConnectorOptional Power Cable Cables and Pin Assignments Technical Specifications Specifications Criteria Technical Specifications Glossary 511Bridged tap COM port Factory defaults EthernetFrame relay 703 Reset LoopbackRouter Telnet GL-4 Index IN-1 IN-2 IN-3 IN-4