MIB Support, Network | Paradyne HOTWIRE 7986 manual

About the Model 7986 Standalone Termination Unit

MIB Support

The Model 7986 Standalone Termination Unit supports traps as defined in

RFC 1215. They may include variable-bindings specified in the following MIBs:

HMIB II (RFC 1573) ± Defines the general objects for use with a network management protocol in TCP/IP internets and provides general information about the Model 7986 Standalone Termination Unit.

HEnterprise MIB ± Supports configuration, status, statistics, and tests.

Figure 1-4 illustrates a typical M/HDSL SNMP configuration. Refer to Chapter 8,

IP Addressing and Appendix B, Standards Compliance for SNMP Traps.

Operation, Maintenance

and Provisioning Center

Network

Router

G.703

4-Wire

DSL

EOC 7986

8786

AC

T5A

250V

AC	.
INPUT	. ..

8600 Ethernet

DSLAM Interface

Ethernet

LAN

SNMP NMS

Data

Voice

98-16088

Figure 1-4. M/HDSL SNMP Configuration

Figure 1-5 illustrates an M/HDSL SNMP configuration connected directly to the Communications Port. Refer to Chapter 8, IP Addressing and Appendix B, Standards Compliance for SNMP Traps .

Router

G.703

DSL

G.703

EOC

COM

7986

7986

Router

SNMP NMS

98-16090

Figure 1-5. M/HDSL Local SNMP Configuration

7986-A2-GB20-00

September 1998

1-5

Image 15

Paradyne HOTWIRE 7986 manual MIB Support, Network

Contents

HOTWIRE Model Hdsl Standalone Termination Unit Copyright E 1998 Paradyne Corporation All rights reserved Important Safety Instructions EMI Warnings Contents Initial Startup and Configuration Messages and Troubleshooting Standards Compliance for Snmp Traps About This Guide Document Purpose and Intended AudienceDocument Summary Product-Related Documents Hdsl Overview About the Model 7986 Standalone Termination Unit Hotwire 7986 Termination Unit Features CO Site Network Configuration Rear Panel Interface Connections Front Panel LED Status Indicators Network MIB Support About the Model 7986 Standalone Termination Unit Using the Asynchronous Terminal Interface User Interface AccessCommunication Port Settings Initiating an ATI Session Login Function SelectScreen Area Main Field Value Choices Messages Screen Work AreasInput Keys Navigating the Screens Keyboard KeysPress For the screen function Select Press Enter to Screen Function Keys Example Switching Between Screen Work Areas Ending an ATI Session Using the Asynchronous Terminal Interface Overview Initial Startup and Configuration +24 Vdc Power Supply Pinouts Connecting Power to the UnitOptional Power Sources Connecting the Unit to an Optional External DC Power Source Connecting to a System Terminal Connecting to the Network Entering Identity Information Main Menu → Control → ChangeIdentity Configuration Option Area Configuration Option Set Choosing a Configuration ModeConfiguring the Unit Using the Configuration Menus Configuration Options Handling Precautions for STATIC-SENSITIVE Devices Configuring the Unit Using the Internal Switches Switchpack S1 & S2 Switchpack Locations Switchpack S1 Definitions Switch # Allows you to Switchpack Definitions OFF = Current Firmware Switchpack S2 Definitions Switch # Allows you toOFF = Autorate Disabled All OFF = If you select Then Accessing and Displaying Configuration OptionsMain Menu → Configuration Load Configuration From Load Configuration from Select To Access To Configure Configuration Edit/DisplayMain Menu → Configuration → Current Configuration Main Menu → Configuration → Default Factory Main Menu → Configuration → Network Configuring AutoRate Time Payload RatePayload Rate Time Rate kbps Kbps Kbps Slots Configuration Loader Main Menu → Configuration → Configuration LoaderConfiguration Loader Completed successfully Save Configuration Saving Configuration Options DSL Download CodeMain Menu → Control → Download Code Download Code Initial Startup and Configuration What to Monitor Monitoring the Unit Viewing System and Test Status Main Menu → Status → System and Test StatusSystem and Test Status Health and Status SELF-TEST Results Health and Status Yyyyyyyy Self-Test Results Call your service Test Status Messages Meaning Test Status Viewing Network Error Statistics Main Menu → Status → Performance → Network Error StatisticsNetwork Error Statistics This Field Contains Viewing Network Performance Statistics This Field Contains Performance Statistics Viewing G.703 Performance Statistics This Field Contains Viewing Model 7986 Standalone Termination Unit LEDs Main Menu → Status → Display LEDsGeneral Model 7986 Standalone Termination Unit LEDs TypeLED is Indicating Test TestingAccessing the Test Menu Main Menu → Running Network Tests Main Menu → Test → Network & G.703 TestsNetwork & G.703 Tests Line Loopback Repeater Loopback DTE Loopback Send Remote Line Loopback Send and Monitor Device Tests Device TestsLamp Test Main Menu → Test → Device Tests Ending an Active Test Testing Messages and Troubleshooting Snmp Traps Options Configuring Snmp Traps Device Messages 1 What Message Indicates What To Do Device Messages 127 Device Messages 2 What Message Indicates What To Do Troubleshooting 1 Symptom Possible Cause Solutions Troubleshooting Troubleshooting 2 Symptom Possible Cause Solutions ATI Access Levels SecurityTables Creating a Login Administer LoginsLogin Entry On the Login Entry screen, for Enter Resetting the Termination Units COM Port or Factory Defaults Deleting a Login If entering yes to prompt Then Security Selecting an IP Addressing Scheme IP Addressing Peer IP Address Assignments IP Addressing Example Configuration Options in , Initial Startup and Configuration Configuration Option Tables Main Menu → Configuration → Current Configuration → Network Interface Options MenuTable A-1. Network Interface Options 1 Circuit Identifier Table A-1. Network Interface Options 2 Port Status Main Menu → Configuration → Load Configuration From → GInterface Options Menu Table A-2. G.703 Interface Options 1 Primary Clock Source Table A-2. G.703 Interface Options 2Line Framing Time Slot System Options Menu Main Menu → Configuration → Load Configuration From →DSL Mode Test Timeout Line Termination Test Duration min Port Use Port Type Possible Settings Asynchronous, SynchronousCommunication Port Table A-4. Communication Port Options 1 Table A-4. Communication Port Options 2 Disconnect Time Minutes Asynchronous mode only Login Required Asynchronous mode onlyPort Access Level Asynchronous mode only Inactivity Timeout Asynchronous mode only Management and Communication Options Menu Telnet Session OptionsTelnet Session Options Table A-5. Telnet Session Options Communication Protocol Options Communication Protocol OptionsPPP Table A-6. Communication Protocol Options 1 Node IP Address Possible Settings 000.000.000.000 ±Node Subnet Mask Possible Settings 000.000.000.000 ± Default Network Destination Communication Port Link Protocol Table A-6. Communication Protocol Options 2 Snmp Traps Options NMS n Destination Table A-7. Snmp Traps Options 1Snmp Traps Number of Trap Managers Link Trap Interfaces Link Traps Possible Settings Disable, Up, Down, BothTable A-7. Snmp Traps Options 2 Enterprise Specific Traps WarmStart AuthenticationFailureStandards Compliance for Snmp Traps Snmp Traps LinkUp/Down Variable-Bindings LinkUp and linkDown Enterprise-Specific Traps EnterpriseFallbackAutoRate Variable-Bindings Hdsl Standards Compliance for Snmp Traps Cables and Pin Assignments E1 Network Interface Table C-2. DSL Network Interface Connector Signal Pin NumberDSL Network Interface Cable COM Port Interface Cable Table C-3. COM Port Interface Connector Signal Pin Number Power Input Connector Optional Power CableTable C-4. DC Power Connector Signal Pin Number Cables and Pin Assignments Specifications Criteria Technical Specifications Technical Specifications COM port Glossary511 Bridged tap 703 Factory defaultsEthernet Frame relay Telnet ResetLoopback Router GL-4 IN-1 Index IN-2 IN-3 IN-4