Configuring AutoRate | Paradyne HOTWIRE 7986 specs

Initial Startup and Configuration

Configuring AutoRate

The M/HDSL AutoRate function is controlled from the Network Interface Options screen and allows you to enable or disable AutoRate only from a unit configured as an LTU. To access the Network Interface screen, follow this menu selection sequence:

Main Menu → Configuration → Network

main/config/network			Hotwire
		Model: 7986
	NETWORK INTERFACE OPTIONS
Margin Threshold:		±3db
Excessive Error Rate Threshold: 1E±6
AutoRate		Disable
DSL Line Rate		528
Peer IP Address:		111.255.255.000 Clear
Circuit Identifier:			Clear

±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±È±±±±±±±±±±±±±±±±±±±±±±±±±±±±±

Ctrl-a to access these functions, ESC for previous menu MainMenu Exit Save

"Procedure

The AutoRate option is defaulted to Disable. To enable AutoRate:

1.Position the cursor in the AutoRate field and press the spacebar.

The AutoRate field toggles to Enable and the DSL Line Rate field displays.

2.Enter a DSL Line Rate and press Enter.

Your payload rate is set to a default value of 1984. Use Table 3-5,Fixed Rate Payload Rates and DSL Line Rates, to set your DSL Line Rate and Payload Rate according to whether you are configured for Voice (signaling) or Data.

3-12

September 1998

7986-A2-GB20-00

Image 38

Paradyne HOTWIRE 7986 manual Configuring AutoRate, Main Menu → Configuration → Network

Contents

HOTWIRE Model Hdsl Standalone Termination Unit Copyright E 1998 Paradyne Corporation All rights reserved Important Safety Instructions EMI Warnings Contents Initial Startup and Configuration Messages and Troubleshooting Standards Compliance for Snmp Traps Document Summary About This GuideDocument Purpose and Intended Audience Product-Related Documents About the Model 7986 Standalone Termination Unit Hdsl Overview Hotwire 7986 Termination Unit Features Network Configuration CO Site Front Panel LED Status Indicators Rear Panel Interface Connections MIB Support Network About the Model 7986 Standalone Termination Unit Communication Port Settings Using the Asynchronous Terminal InterfaceUser Interface Access Login Initiating an ATI Session Area SelectScreen Function Main Keys Screen Work AreasInput Field Value Choices Messages Press Navigating the ScreensKeyboard Keys Screen Function Keys For the screen function Select Press Enter to Switching Between Screen Work Areas Example Ending an ATI Session Using the Asynchronous Terminal Interface Initial Startup and Configuration Overview Connecting the Unit to an Optional External DC Power Source Connecting Power to the UnitOptional Power Sources +24 Vdc Power Supply Pinouts Connecting to the Network Connecting to a System Terminal Identity Entering Identity InformationMain Menu → Control → Change Configuration Options Choosing a Configuration ModeConfiguring the Unit Using the Configuration Menus Configuration Option Area Configuration Option Set Configuring the Unit Using the Internal Switches Handling Precautions for STATIC-SENSITIVE Devices Switchpack Locations Switchpack S1 & S2 Switchpack Definitions Switchpack S1 Definitions Switch # Allows you to All OFF = Switchpack S2 Definitions Switch # Allows you toOFF = Autorate Disabled OFF = Current Firmware Load Configuration from Accessing and Displaying Configuration OptionsMain Menu → Configuration Load Configuration From If you select Then Main Menu → Configuration → Default Factory Configuration Edit/DisplayMain Menu → Configuration → Current Configuration Select To Access To Configure Configuring AutoRate Main Menu → Configuration → Network Kbps Slots Payload RatePayload Rate Time Rate kbps Kbps Time Configuration Loader Configuration LoaderMain Menu → Configuration → Configuration Loader Completed successfully Saving Configuration Options Save Configuration Download Code Download CodeMain Menu → Control → Download Code DSL Initial Startup and Configuration Monitoring the Unit What to Monitor System and Test Status Health and Status SELF-TEST Results Viewing System and Test StatusMain Menu → Status → System and Test Status Health and Status Yyyyyyyy Call your service Self-Test Results Test Status Test Status Messages Meaning Network Error Statistics Viewing Network Error StatisticsMain Menu → Status → Performance → Network Error Statistics This Field Contains Viewing Network Performance Statistics This Field Contains Viewing G.703 Performance Statistics Performance Statistics This Field Contains General Viewing Model 7986 Standalone Termination Unit LEDsMain Menu → Status → Display LEDs LED is Indicating Model 7986 Standalone Termination Unit LEDsType Main Menu → TestingAccessing the Test Menu Test Network & G.703 Tests Running Network TestsMain Menu → Test → Network & G.703 Tests Line Loopback Repeater Loopback DTE Loopback Send Remote Line Loopback Send and Monitor Main Menu → Test → Device Tests Device TestsLamp Test Device Tests Ending an Active Test Testing Messages and Troubleshooting Configuring Snmp Traps Snmp Traps Options Device Messages Device Messages 1 What Message Indicates What To Do Device Messages 2 What Message Indicates What To Do 127 Troubleshooting Troubleshooting 1 Symptom Possible Cause Solutions Troubleshooting 2 Symptom Possible Cause Solutions Tables ATI Access LevelsSecurity Login Entry Creating a LoginAdminister Logins On the Login Entry screen, for Enter Deleting a Login Resetting the Termination Units COM Port or Factory Defaults If entering yes to prompt Then Security IP Addressing Selecting an IP Addressing Scheme IP Addressing Example Peer IP Address Assignments Configuration Option Tables Configuration Options in , Initial Startup and Configuration Table A-1. Network Interface Options 1 Main Menu → Configuration → Current Configuration →Network Interface Options Menu Table A-1. Network Interface Options 2 Circuit Identifier Table A-2. G.703 Interface Options 1 Main Menu → Configuration → Load Configuration From → GInterface Options Menu Port Status Time Slot Table A-2. G.703 Interface Options 2Line Framing Primary Clock Source Test Timeout Main Menu → Configuration → Load Configuration From →DSL Mode System Options Menu Test Duration min Line Termination Table A-4. Communication Port Options 1 Port Type Possible Settings Asynchronous, SynchronousCommunication Port Port Use Table A-4. Communication Port Options 2 Inactivity Timeout Asynchronous mode only Login Required Asynchronous mode onlyPort Access Level Asynchronous mode only Disconnect Time Minutes Asynchronous mode only Telnet Session Options Management and Communication Options MenuTelnet Session Options Table A-5. Telnet Session Options PPP Communication Protocol OptionsCommunication Protocol Options Default Network Destination Node IP Address Possible Settings 000.000.000.000 ±Node Subnet Mask Possible Settings 000.000.000.000 ± Table A-6. Communication Protocol Options 1 Table A-6. Communication Protocol Options 2 Communication Port Link Protocol Snmp Traps Options Number of Trap Managers Table A-7. Snmp Traps Options 1Snmp Traps NMS n Destination Enterprise Specific Traps Link Traps Possible Settings Disable, Up, Down, BothTable A-7. Snmp Traps Options 2 Link Trap Interfaces Snmp Traps AuthenticationFailureStandards Compliance for Snmp Traps WarmStart LinkUp and linkDown LinkUp/Down Variable-Bindings Enterprise-Specific Traps EnterpriseFallbackAutoRate Variable-Bindings Hdsl Standards Compliance for Snmp Traps Cables and Pin Assignments E1 Network Interface DSL Network Interface Cable Table C-2. DSL Network Interface ConnectorSignal Pin Number Table C-3. COM Port Interface Connector Signal Pin Number COM Port Interface Cable Table C-4. DC Power Connector Signal Pin Number Power Input ConnectorOptional Power Cable Cables and Pin Assignments Technical Specifications Specifications Criteria Technical Specifications Bridged tap Glossary511 COM port Frame relay Factory defaultsEthernet 703 Router ResetLoopback Telnet GL-4 Index IN-1 IN-2 IN-3 IN-4