Health and Status | Paradyne HOTWIRE 7986 specification

Monitoring the Unit

Health and Status

The following messages can appear in the first column of the System and Test Status screen. The highest priority Health and Status message also appears on all ATI screens on the bottom right.

Table 4-1. Health and Status Messages (1 of 2)

Message

What Message Indicates

What To Do

System Operational	There are no problems
	detected.

LOS at Net, Pt 1	An LOS (Loss Of Signal)	1. Verify that the network cable is
	condition has been	securely attached at both ends.
	detected on the network	2. Contact network provider.
	interface. No signal is	2. Contact network provider.
	interface. No signal is
	being received on Port 1,
	possibly due to a local
	network problem.

OOF at Net, Pt 1	An OOF (Out Of Frame)	1. Check the Transmit Clock Source
	condition has been	configuration options. Do not set
	detected.	both the local and remote unit to
		Internal, External, or Loop timing.
		2. Contact network provider.

LOF at G.703, Pt 1	An LOF (Loss Of Frame)	1. Verify that the network cable is
	condition has been	securely attached at both ends.
	detected on the G.703	2. Contact network provider.
	interface.	2. Contact network provider.
	interface.

AIS at G.703, Pt 1	An Alarm Indication Signal	1. Check the Transmit Clock Source
	(AIS) is being received by	configuration options. Do not set
	the G.703 interface.	both the local and remote unit to
		Internal, External, or Loop timing.
		2. Contact network provider.

EER at Net, Pt 1	An EER (Excessive Error	Contact network provider.
	Rate) condition has been
	detected on the network
	interface at Port 1. The
	condition is cleared when
	the error rate falls below
	the threshold value
	currently configured.

EER at G.703, Pt 1	An EER (Excessive Error	Contact network provider.
	Rate) condition has been
	detected on the G.703
	interface.

RAI (Remote Alarm	An Remote Alarm	Contact network provider.
Indication) at G.703	Indication signal is being
interface, Pt 1	received by the G.703
	interface.

Net Margin	The signal-to-noise margin	Contact network provider.
Threshold, Pt 1	has exceeded the
	configured threshold.

7986-A2-GB20-00

September 1998

4-3

Image 47

Paradyne HOTWIRE 7986 manual Health and Status

Contents

HOTWIRE Model Hdsl Standalone Termination Unit Copyright E 1998 Paradyne Corporation All rights reserved Important Safety Instructions EMI Warnings Contents Initial Startup and Configuration Messages and Troubleshooting Standards Compliance for Snmp Traps Document Summary About This GuideDocument Purpose and Intended Audience Product-Related Documents Hdsl Overview About the Model 7986 Standalone Termination Unit Hotwire 7986 Termination Unit Features CO Site Network Configuration Rear Panel Interface Connections Front Panel LED Status Indicators Network MIB Support About the Model 7986 Standalone Termination Unit Communication Port Settings Using the Asynchronous Terminal InterfaceUser Interface Access Initiating an ATI Session Login Function SelectScreen Area Main Field Value Choices Messages Screen Work AreasInput Keys Press Navigating the ScreensKeyboard Keys For the screen function Select Press Enter to Screen Function Keys Example Switching Between Screen Work Areas Ending an ATI Session Using the Asynchronous Terminal Interface Overview Initial Startup and Configuration +24 Vdc Power Supply Pinouts Connecting Power to the UnitOptional Power Sources Connecting the Unit to an Optional External DC Power Source Connecting to a System Terminal Connecting to the Network Identity Entering Identity InformationMain Menu → Control → Change Configuration Option Area Configuration Option Set Choosing a Configuration ModeConfiguring the Unit Using the Configuration Menus Configuration Options Handling Precautions for STATIC-SENSITIVE Devices Configuring the Unit Using the Internal Switches Switchpack S1 & S2 Switchpack Locations Switchpack S1 Definitions Switch # Allows you to Switchpack Definitions OFF = Current Firmware Switchpack S2 Definitions Switch # Allows you toOFF = Autorate Disabled All OFF = If you select Then Accessing and Displaying Configuration OptionsMain Menu → Configuration Load Configuration From Load Configuration from Select To Access To Configure Configuration Edit/DisplayMain Menu → Configuration → Current Configuration Main Menu → Configuration → Default Factory Main Menu → Configuration → Network Configuring AutoRate Time Payload RatePayload Rate Time Rate kbps Kbps Kbps Slots Configuration Loader Configuration LoaderMain Menu → Configuration → Configuration Loader Completed successfully Save Configuration Saving Configuration Options DSL Download CodeMain Menu → Control → Download Code Download Code Initial Startup and Configuration What to Monitor Monitoring the Unit System and Test Status Health and Status SELF-TEST Results Viewing System and Test StatusMain Menu → Status → System and Test Status Health and Status Yyyyyyyy Self-Test Results Call your service Test Status Messages Meaning Test Status Network Error Statistics Viewing Network Error StatisticsMain Menu → Status → Performance → Network Error Statistics This Field Contains Viewing Network Performance Statistics This Field Contains Performance Statistics Viewing G.703 Performance Statistics This Field Contains General Viewing Model 7986 Standalone Termination Unit LEDsMain Menu → Status → Display LEDs LED is Indicating Model 7986 Standalone Termination Unit LEDsType Test TestingAccessing the Test Menu Main Menu → Network & G.703 Tests Running Network TestsMain Menu → Test → Network & G.703 Tests Line Loopback Repeater Loopback DTE Loopback Send Remote Line Loopback Send and Monitor Device Tests Device TestsLamp Test Main Menu → Test → Device Tests Ending an Active Test Testing Messages and Troubleshooting Snmp Traps Options Configuring Snmp Traps Device Messages 1 What Message Indicates What To Do Device Messages 127 Device Messages 2 What Message Indicates What To Do Troubleshooting 1 Symptom Possible Cause Solutions Troubleshooting Troubleshooting 2 Symptom Possible Cause Solutions Tables ATI Access LevelsSecurity Login Entry Creating a LoginAdminister Logins On the Login Entry screen, for Enter Resetting the Termination Units COM Port or Factory Defaults Deleting a Login If entering yes to prompt Then Security Selecting an IP Addressing Scheme IP Addressing Peer IP Address Assignments IP Addressing Example Configuration Options in , Initial Startup and Configuration Configuration Option Tables Table A-1. Network Interface Options 1 Main Menu → Configuration → Current Configuration →Network Interface Options Menu Circuit Identifier Table A-1. Network Interface Options 2 Port Status Main Menu → Configuration → Load Configuration From → GInterface Options Menu Table A-2. G.703 Interface Options 1 Primary Clock Source Table A-2. G.703 Interface Options 2Line Framing Time Slot System Options Menu Main Menu → Configuration → Load Configuration From →DSL Mode Test Timeout Line Termination Test Duration min Port Use Port Type Possible Settings Asynchronous, SynchronousCommunication Port Table A-4. Communication Port Options 1 Table A-4. Communication Port Options 2 Disconnect Time Minutes Asynchronous mode only Login Required Asynchronous mode onlyPort Access Level Asynchronous mode only Inactivity Timeout Asynchronous mode only Telnet Session Options Management and Communication Options MenuTelnet Session Options Table A-5. Telnet Session Options PPP Communication Protocol OptionsCommunication Protocol Options Table A-6. Communication Protocol Options 1 Node IP Address Possible Settings 000.000.000.000 ±Node Subnet Mask Possible Settings 000.000.000.000 ± Default Network Destination Communication Port Link Protocol Table A-6. Communication Protocol Options 2 Snmp Traps Options NMS n Destination Table A-7. Snmp Traps Options 1Snmp Traps Number of Trap Managers Link Trap Interfaces Link Traps Possible Settings Disable, Up, Down, BothTable A-7. Snmp Traps Options 2 Enterprise Specific Traps WarmStart AuthenticationFailureStandards Compliance for Snmp Traps Snmp Traps LinkUp/Down Variable-Bindings LinkUp and linkDown Enterprise-Specific Traps EnterpriseFallbackAutoRate Variable-Bindings Hdsl Standards Compliance for Snmp Traps Cables and Pin Assignments E1 Network Interface DSL Network Interface Cable Table C-2. DSL Network Interface ConnectorSignal Pin Number COM Port Interface Cable Table C-3. COM Port Interface Connector Signal Pin Number Table C-4. DC Power Connector Signal Pin Number Power Input ConnectorOptional Power Cable Cables and Pin Assignments Specifications Criteria Technical Specifications Technical Specifications COM port Glossary511 Bridged tap 703 Factory defaultsEthernet Frame relay Telnet ResetLoopback Router GL-4 IN-1 Index IN-2 IN-3 IN-4