Roland RD-700 112, Gated Reverb, 26 OD→CHORUS Overdrive→Chorus, 27 OD→FLANGER Overdrive→Flanger

Appendices

Effect/Parameter List

Time (Reverb Time) #

Adjust the time length of reverberation.

HF Damp

Adjust the frequency above which the reverberant sound will be cut. As the frequency is set lower, more of the high frequencies will be cut, resulting in a softer and more muted reverberance. If you do not want the high frequencies to be cut, set this parameter to BYPASS.

Low Gain

Adjust the gain of the low frequency range.

Positive (+) settings will emphasize (boost) the low frequency range.

High Gain

Adjust the gain of the high frequency range.

Positive (+) settings will emphasize (boost) the high frequency range.

Balance (Effect Balance) #

Adjust the volume balance between the direct sound and the reverb sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the reverb sound will be output.

Level (Output Level)

Adjust the output level.

25: GATED REVERB

Gate Reverb is a special type of reverb in which the reverberant sound is cut off before its natural length.

Type (Gated Reverb Type)

Select the type of reverb.

NORMAL: conventional gate reverb

REVERSE: backwards reverb

SWEEP1: the reverberant sound moves from right to left

SWEEP2: the reverberant sound moves from left to right

Pre Delay (Pre Delay Time)

Adjust the time delay from when the direct sound begins until the reverb sound is heard.

Gate Time

Adjust the time from when the reverb is heard until when it disappears.

Low Gain

Adjust the gain of the low frequency range.

Positive (+) settings will emphasize (boost) the low frequency range.

High Gain

Adjust the gain of the high frequency range.

Positive (+) settings will emphasize (boost) the high frequency range.

Balance (Effect Balance) #

Adjust the volume balance between the direct sound and the reverb sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the reverb sound will be output.

Level (Output Level) #

Adjust the output level.

26: OD→CHORUS (Overdrive→Chorus)

This effect connects an overdrive and a chorus in series.

OD Drive

Adjust the degree of overdrive distortion. The volume will change together with the degree of distortion.

OD Pan (Overdrive Pan) #

Adjust the stereo location of the overdrive sound. L64 is far left, 0 is center, and 63R is far right.

Cho Delay (Chorus Pre Delay Time)

Adjust the time delay from when the direct sound begins until the chorus sound is heard.

Cho Rate (Chorus Rate)

Adjust the modulation speed of the chorus effect.

Cho Depth (Chorus Depth)

Adjust the modulation depth of the chorus effect.

Cho Bal (Chorus Balance) #

Adjust the volume balance between the overdrive sound that is sent through the chorus and the overdrive sound that is not sent through the chorus. With a setting of “D100:0W,” only the overdrive sound will be output. With a setting of “D0:100W,” only the overdrive sound that is sent through the chorus will be output.

Level (Output Level)

Adjust the output level.

27: OD→FLANGER (Overdrive→Flanger)

This effect connects an overdrive and a flanger in series.

OD Drive

Adjust the degree of overdrive distortion. The volume will change together with the degree of distortion.

OD Pan (Overdrive Pan) #

Adjust the stereo location of the overdrive sound. L64 is far left, 0 is center, and 63R is far right.

Flg Delay (Flanger Pre Delay Time)

Adjust the time delay from when the direct sound begins until the flanger sound is heard.

Flg Rate (Flanger Rate)

Adjust the modulation speed of the flanger effect.

Flg Depth (Flanger Depth)

Adjust the modulation depth of the flanger effect.

Flg Fbk (Flanger Feedback Level)

Adjust the proportion (%) of the flanger sound that is fed back into the effect. Negative (-) settings will invert the phase.

112