Roland RD-700 owner manual 116, Keysync Flang Keysync Flanger, Formant Filtr Formant Filter

Appendices

Effect/Parameter List

StpRateSw (Step Rate Switch)

This setting determines whether the pitch is changed in a stepped fashion (ON) or not (OFF).

Mix (Mix Level)

Adjust the volume of the phase-shifted sound, relative to the direct sound.

Low Gain

Adjust the low frequency gain (amount of boost or cut). Positive (+) settings will emphasize (boost) the low frequency range.

High Gain

Adjust the high frequency gain (amount of boost or cut). Positive (+) settings will emphasize (boost) the high frequency range.

Level (Output Level)

Adjust the output level.

42: KEYSYNC FLANG (Keysync Flanger)

Keysync Flanger controls the Flanger by resetting the effect at the volume of the sound input to the effects device, restarting from the same pitch each time the Flanger is reset.

This parameter lets your playing dynamics on the keyboard control the flanger effect.

Pre Delay (Pre Delay Time)

Adjust the time delay from the direct sound until the flanger sound is heard.

Rate (LFO Rate) #

Adjust the modulation frequency of the flanger sound.

➔Rate parameter can be set as a note-value of a tempo. In this case, specify the value of the desired note.

Depth (LFO Depth)

Adjust the modulation depth of the flanger sound.

Feedback #

Adjust the proportion (%) of the flanger sound that is to be returned to the input. Positive (+) settings will return the signal to the input with the original phase, while negative (-) settings produce an inverted phase. Higher settings will produce a more distinctive sound.

Phase

Adjust the spaciousness of the flanger sound.

Filter (Filter Type)

OFF: A filter will not be used.

LPF: The frequency region above the Cutoff setting will be cut.

HPF: The frequency region below the Cutoff setting will be cut.

Cutoff (Cutoff Frequency)

Sets the cutoff frequency when a specific frequency band is cut off by a filter.

Step Rate #

Adjust the frequency of pitch change.

➔Step Rate parameter can be set as a note-value of a tempo. In this case, specify the value of the desired note.

StpRateSw (Step Rate Switch)

This setting determines whether the pitch is changed in a stepped fashion (ON) or not (OFF).

Key Sync (Keysync Switch)

Determines whether the Flanger LFO is reset according to the input sound (ON) or not (OFF).

Threshold (Keysync Threshold)

Adjust the volume level for which reset will be applied.

KSync Phs (Keysync Phase)

Sets the LFO phase when the LFO is reset.

Low Gain

Adjust the low frequency range gain (amount of boost or cut). Positive (+) settings will emphasize (boost) the low frequency range.

High Gain

Adjust the high frequency gain (amount of boost or cut). Positive (+) settings will emphasize (boost) the high frequency range.

Balance #

Adjusts the volume balance between the direct sound and the flanger sound.

With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W the flanger sound will be output.

Level (Output Level)

Adjust the output level.

43: FORMANT FILTR (Formant Filter)

This adds a vowel character to the sound, making it similar to a human voice.

Drive Sw (Drive Switch)

Turns Drive on/off.

Drive #

Specifies the depth of distortion. The volume will change together with the degree of distortion.

Vowel 1

Selects the vowel 1.

Vowel 2

Selects the vowel 2.

Rate #

Sets the frequency at which the two vowels will be switched.

➔Rate parameter can be set as a note-value of a tempo. In this case, specify the value of the desired note.

Depth #

Sets the effect depth.

Key Sync (KeySync Switch)

Determines whether the LFO for switching the vowels is reset according to the input sound (ON) or not (OFF).

Threshold (Keysync Threshold)

Specifies the volume level for which reset will be applied.

116