Roland RD-700 owner manual 123, 60 3D Chorus, 61 3D Flanger

AP Mid Sw (Anti Phase Middle Switch)

This turns the Anti-Phase function on and off and sets the level settings for the Middle frequency ranges. When turned on, the counter-channel of stereo sound is inverted and added to the signal.

AP Mid (Anti Phase Middle Level)

Sets the level of the separate midrange (Middle) anti-phase function. With some settings, you can get a sort of abstract sound in the specified Part.

Adjusting these levels for certain frequencies allows you to lend emphasis to specific parts. (This is effective only for stereo source.)

AP Low Sw (Anti Phase Low Switch)

This turns the Anti-Phase function on and off and sets the level settings for the Low frequency ranges. When turned on, the counter-channel of stereo sound is inverted and added to the signal.

AP Low Sw (Anti Phase Low Switch)

Sets the level of the separate Lowrange anti-phase function. With some settings, you can get a sort of abstract sound in the specified Part.

Adjusting these levels for certain frequencies allows you to lend emphasis to specific parts. (This is effective only for stereo source.)

Boost Sw (Low Booster Switch)

Adjust whether Low Booster will be used (ON) or not (OFF). This emphasizes the bottom to create a heavy bass sound.

Boost Lvl (Low Booster Level)

Adjust the level. Increasing this value gives you a heavier low end. (Depending on the Isolator and filter settings this effect may be hard to distinguish.)

Level (Output Level)

Adjust the output level.

60: 3D CHORUS

This applies a 3D effect to the chorus sound. The chorus sound will be positioned 90 degrees left and 90 degrees right.

Pre Delay (Pre Delay Time)

Adjust the time delay from the direct sound until when the chorus sound is heard.

Rate (LFO Rate) #

Adjust the modulation frequency of the chorus sound.

➔Rate parameter can be set as a note-value of a tempo. In this case, specify the value of the desired note.

Depth (LFO Depth)

Adjust the modulation depth of the chorus sound.

Phase

Adjust the spaciousness of the chorus sound.

Fltr Type

OFF: A filter will not be used.

LPF: The frequency region above the Cutoff Freq setting will be

cut.

HPF: The frequency region below the Cutoff Freq setting will be

cut.

Effect/Parameter List

Cutoff (Cutoff Frequency)

Sets the cutoff frequency when a specific frequency band is cut off by a filter.

Out (Output Mode)

Adjust the method that will be used to hear the output sound. The optimal 3D effect will be achieved if you select SPEAKER when using speakers, or PHONES when using headphones.

Low Gain

Adjust the low frequency gain (amount of boost or cut). Positive (+) settings will emphasize (boost) the low frequency range.

High Gain

Adjust the high frequency gain (amount of boost or cut). Positive (+) settings will emphasize (boost) the high frequency range.

Balance #

Adjust the volume balance between the direct sound and the flanger sound.

With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the flanger sound will be output.

Level (Output Level)

Adjust the output level.

61: 3D FLANGER

This applies a 3D effect to the flanger sound. The flanger sound will be positioned 90 degrees left and 90 degrees right.

Pre Delay (Pre Delay Time)

Adjust the time delay from the direct sound until the flanger sound is heard.

Rate (LFO Rate) #

Adjust the modulation speed of the flanger sound.

➔Rate parameter can be set as a note-value of a tempo. In this case, specify the value of the desired note.

Depth (LFO Depth)

Adjust the modulation depth of the flanger sound.
Feedback #
Adjust the proportion (%) of the flanger sound that is to be
returned to the input. Positive (+) settings will return the signal
to the input with the original phase, while negative (-) settings
produce an inverted phase. Higher settings will produce a more
distinctive sound.
Phase
Adjust the spaciousness of the flanger sound.
Filter (Filter Type)
OFF: No filter is used.
LPF: The frequency region above the Cutoff Freq setting will be	Appendices
cut.
HPF: The frequency region below the Cutoff Freq setting will be
cut.

123