Roland RD-700 owner manual Midi Implementation, 147, Pitch Bend Change

❍Release Time (Controller number 72)

Status	2nd byte	3rd byte
BnH	48H	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)

vv = Release Time value (relative change): 00H - 7FH (-64 - 0 - +63),

*The Release Time parameter (EDIT:Tone Edit:Release Time) will change.

❍Attack time (Controller number 73)

Status	2nd byte	3rd byte
BnH	49H	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Attack time value (relative change):		00H - 7FH (-64 - 0 - +63),

*The Attack Time parameter (EDIT:Tone Edit:Attack Time) will change.

❍Cutoff (Controller number 74)

Status	2nd byte	3rd byte
BnH	4AH	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Cutoff value (relative change):		00H - 7FH (-64 - 0 - +63)

*The Cutoff parameter (EDIT:Tone Edit:Cutoff) will change.

❍Decay Time (Controller number 75)

Status	2nd byte	3rd byte
BnH	4BH	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Decay Time value (relative change):		00H - 7FH (-64 - 0 - +63)

*The decay time will change in GM mode.

❍Vibrato Rate (Controller number 76)

Status	2nd byte	3rd byte
BnH	4CH	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Vibrato Rate value (relative change):		00H - 7FH (-64 - 0 - +63)

*The vibrato rate will change in GM mode.

❍Vibrato Depth (Controller number 77)

Status	2nd byte	3rd byte
BnH	4DH	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)

vv = Vibrato Depth Value (relative change):00H - 7FH (-64 - 0 - +63)

*The vibrato depth will change in GM mode.

❍Vibrato Delay (Controller number 78)

Status	2nd byte	3rd byte
BnH	4EH	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)

vv = Vibrato Delay value (relative change):00H - 7FH (-64 - 0 - +63)

*The vibrato delay will change in GM mode.

❍Portamento Control (Controller number 84)

Status	2nd byte	3rd byte
BnH	54H	kkH
n = MIDI channel number:		0H - FH (ch.1 - 16)
kk = source note number:		00H - 7FH (0 - 127)

*A Note-on received immediately after a Portamento Control message will change continuously in pitch, starting from the pitch of the Source Note Number.

*If a voice is already sounding for a note number identical to the Source Note Number, this voice will continue sounding (i.e., legato) and will, when the next Note-on is received, smoothly change to the pitch of that Note-on.

*The rate of the pitch change caused by Portamento Control is determined by the Portamento Time value.

❍Effect 1 (Reverb Send Level) (Controller number 91)

Status	2nd byte	3rd byte
BnH	5BH	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Reverb Send Level:		00H - 7FH (0 - 127)

*The Reverb Amount parameter (EDIT:Tone Edit:Reverb Amount) will change.

MIDI Implementation

❍Effect 3 (Chorus Send Level) (Controller number 93)

Status	2nd byte	3rd byte
BnH	5DH	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Chorus Send Level:		00H - 7FH (0 - 127)

*The Chorus Amount parameter (EDIT:Tone Edit:Chorus Amount) will change.

❍RPN MSB/LSB (Controller number 100, 101)

Status	2nd byte	3rd byte
BnH	65H	mmH
BnH	64H	llH

n = MIDI channel number: 0H - FH (ch.1 - 16)

mm= upper byte (MSB) of parameter number specified by RPN ll = lower byte (LSB) of parameter number specified by RPN

<<< RPN >>>

Control Changes include RPN (Registered Parameter Numbers), which are extended. When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any order) should be sent in order to select the parameter, then

Data Entry (Controller numbers 6 and 38) should be sent to set the value. Once RPN messages are received, Data Entry messages that is received at the same MIDI channel after that are recognized as changing toward the value of the RPN messages. In order not to make any mistakes, transmitting RPN Null is recommended after setting parameters you need.

This device receives the following RPNs.

RPN	Data entry
MSB, LSB	MSB, LSB	Notes
00H, 00H	mmH, llH	Pitch Bend Sensitivity
		mm: 00H - 18H (0 - 24 semitones)
		ll: ignored (processed as 00H)
		Up to 2 octave can be specified in semitone steps.
		*	The Bend Range parameter (EDIT:Tone	Edit:Bend
			Range) will change.
00H, 01H	mmH, llH	Channel Fine Tuning
		mm, ll: 20 00H - 40 00H - 60 00H
		(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
		* The Fine Tune parameter (EDIT:Tone Edit:Fine Tune)
			will change.
00H, 02H	mmH, llH	Channel Coarse Tuning
		mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
		ll: ignored (processed as 00H)
		*	The Coarse Tune parameter (EDIT:Tone	Edit:Coarse
			Tune) will change.
00H, 05H	mmH, llH	Modulation Depth Range
		mm, ll: 00 00H - 06 00H ( 0 - 16384 * 600 / 16384 cent)
		* The modulation depth range will change in GM mode.
7FH, 7FH	---, ---	RPN null
		RPN and NRPN will be set as “unspecified.” Once this
		setting has been made, subsequent Parameter values that
		were previously set will not change.
		mm, ll: ignored

●Program Change

Status	2nd byte
CnH	ppH
n = MIDI channel number:		0H - FH (ch.1 - 16)
pp = Program number:		00H - 7FH (prog.1 - prog.128)

*Not received when the Rx Program Change parameter (EDIT:Internal Part Parameter:Rx Program Chanage) is OFF.

●Pitch Bend Change

Status	2nd byte	3rd byte
EnH	llH	mmH
n = MIDI channel number:		0H - FH (ch.1 - 16)	Appendices
mm, ll = Pitch Bend value:		00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)

* Not received when the Rx Bender parameter (EDIT:Internal Part Parameter:Rx Bender) is OFF.

147