Configuring network protocol via the machine

You can set up TCP/IP network parameters, follow the steps listed below.

1.Make sure your machine is connected to the network with an RJ-45 Ethernet cable.

2.Make sure you have turned on the machine.

3.Press Machine Setup on the control panel.

4.Press Admin Setting.

5.When the login message appears, enter password. Touch the password input area, then the question marks appears. Use the number keypad on the control panel to enter the password. Once the password is entered, press OK. (Factory setting:1111)

6.Press the Setup tab > Network Setup.

7.Select TCP/IP Protocol.

Ethernet Speed: You can select the communication speed for Ethernet connections.

8.Press IP Setting.

9.Select Static and then enter IP Address, Subnet Mask and Gateway address fields. Touch the input area then, enter addresses by number keypad on the control panel.

Contact the network administrator if you are not sure how to configure.

10.Press OK.

You can also set up the network settings through the network administration programs.

SyncThru™ Web Admin Service: Web-based printer management solution for network administrators. SyncThru™ Web Admin Service provides you with an efficient way of managing network devices and lets you remotely monitor and troubleshoot network machines from any site with corporate internet access. Download this program from http:// solution.samsungprinter.com.

SyncThru™ Web Service: This is web server embedded on your network printer. If you login with administrator’s ID and password on the web server, it allows you to:

-Configure the network parameters necessary for the machine to connect to various network environemnts.

-Customize machine settings.

-Customize email settings and set up address book for scanning to email.

-Customize server settings and set up address book for scanning to the FTP or SMB servers.

-Customize printer, copy, and fax settings

SetIP: Utility program allowing you to select a network interface and manually configure the IP addresses for use with the TCP/IP protocol. See "Using the SetIP program" on page 31.

SYSTEM REQUIREMENTS

Before you begin, ensure that your system meets the following requirements:

Windows

 

REQUIREMENT (RECOMMENDED)

OS

 

 

 

CPU

RAM

FREE HDD

 

 

SPACE

 

 

 

 

 

 

 

Windows 2000

Pentium II 400 MHz

64 MB

600 MB

 

(Pentium III 933 MHz)

(128 MB)

 

 

 

 

 

Windows XP

Pentium III 933 MHz

128 MB

1.5 GB

 

(Pentium IV 1 GHz)

(256 MB)

 

 

 

 

 

Windows

Pentium III 933 MHz

128 MB

1.25 GB to

Server 2003

(Pentium IV 1 GHz)

(512 MB)

2 GB

 

 

 

 

Windows

Pentium IV 3 GHz

512 MB

15 GB

 

 

(1024 MB)

 

 

 

 

 

Windows

Pentium IV 1 GHz

512 MB

10 GB

Server 2008

(Pentium IV 2 GHz)

(2048 MB)

 

 

 

 

 

Windows 7

Pentium IV 1 GHz 32-

1 GB

16 GB

 

bit or 64-bit processor

(2 GB)

 

 

or higher

 

 

 

 

 

 

Support for DirectX 9 graphics with 128 MB memory(to enable the Aero theme).

DVD-R/W Drive

Windows

Pentium IV 1

512 MB

10 GB

Server 2008

GHz(x86) or

(2048 MB)

 

R2

1.4GHz(x64)

 

 

 

processors(2GHz or

 

 

 

faster)

 

 

 

 

 

 

• Internet Explorer 5.0 or higher is the minimum requirement for all Windows operating systems.

Users who have an administrator right can install the software.

Windows Terminal Services is compatable with this machine.

27

Page 27
Image 27
Samsung SCX-6555NX System Requirements, Configuring network protocol via the machine, Windows, Requirement Recommended