Misfeed in the upper paper tray | Sharp AR-M208 specification

MISFEED REMOVAL

Misfeed in the upper paper tray

Before opening the upper paper tray, be sure to open the bypass tray and the side cover and then perform steps 1 to 3 described in the "A. Misfeed in the paper feed area" section.

1 Pull out the upper paper tray and remove the misfed paper.

2 Close the paper tray.

COPIER TROUBLE?

3 Open and close the side cover to cancel the misfeed display.

●You can also cancel the misfeed display by opening and closing the front cover.

●Confirm that the misfeed display has been cleared.

Misfeed in the lower paper tray

1 Grasp the handle of the lower side cover and gently open the cover.

80

Image 82

Sharp AR-M208 operation manual Misfeed in the upper paper tray, Misfeed in the lower paper tray

Contents

AR-M208 For Your Records Outline of this Manual Making Copies Contents Contents Contents Chapter Getting Started Introduction Conventions used in this manual Safety Precautions Copier Installation Do not install your copier in areas that are Copier Installation High-speed laser copying Main FeaturesSubstantial copying features High-quality digital image Scan once/ Print many Printer featuresOptional features Environmentally friendly design Part Names and Functions Exterior Interior Operation panel Output key p Auto Image key pSided Copy key p Special Function key Power off Power on and OFFPower on Dehumidification heater switch DH Power Preheat mode Initial settingsPower save modes Auto power shut-off mode Function Icons Use the and keys to select a function Function ReviewPress the JOB Status key To exit the review screen, press the Back key Enter your account number using the numeric keys How to copy in the auditing modeAuditing Accounts When copying is completed, press the Audit Clear key Please see your key operator for assistance Getting Started Making Copies Original size scale Copying from Platen GlassClose the platen cover Ensure that the desired paper tray is selected Set the number of copies using the numeric keysPress the Start key About reversing single pass feeder Rspf Using the RspfCopying from the Rspf Acceptable originals Set the originals face up in the document feeder tray Set the number of copies and press the Start key TWO-SIDED Copying Copy ModeUsing the Rspf Two-sided copies from one-sided originals Use the and keys to select one-sided to two-sided copying Using the platen glassBinding Change OFF OK key Copy Mode Two-sided copies from two-sided originals Only when a Rspf is being usedKey again Press the OK key One-sided copies from two-sided originalsUse the and keys to select two-sided to two-sided copying Document feeder tray 12 to Use the and keys to select two-sided to one-sided copying Text, text/photo, and photo Exposure AdjustmentAuto Press the Exposure key Use the and keys to adjust the copy density as desired Text Automatic selection Reduction ENLARGEMENT/ZOOMPaper size Press the Auto Image key Enter the number of copies and press the Start key Press the Copy Ratio key Use the and keys to select a preset copy ratio or useManual selection Keys to select a zoom ratio Press the OK key Rotation Copying Use the Paper Select key to select the desired tray Copying from the bypass tray Acceptable paper for copying from the bypass trayUnfold the bypass tray SET Extra Image ADJPress the Paper Select key to select the bypass tray Copy of first original Second original Set an original for interrupt copying Interrupting a Copy RUNPress the Interrupt key Select the desired available copier functions Used for interrupt copying When all Interrupt copies are finished, press the InterruptKey to resume copying Interrupting a Copy RUN Special Functions Group mode Copying in the sort or group modeSort mode SORT/GROUP Group SortPress the Output key Offset stack Erase Margin ShiftSpecial Modes Press the Special Function key. Then press the OK key Margin Shift OFF Down To select the shift amount Center EraseErase OFF Use the and keys to select Erase and press the OK key Use the and keys to select the desired erase mode Dual page Copy Special Modes Margin Shift Erase Okoff on 1 or 4 Use the and keys to select 2in1/4in1 and press the OK key OkchangeBorder no Use the and keys to select the desired layout pattern Border Use the and keys to select a type of border line XY Zoom ReverseUse the and keys to select B/W Reverse and press the OK key Reverse XY Zoom Direction Use the and keys to select XY Zoom and press the OK keyPress the key 81 11R Transparency Special Modes XY Zoom Reverse Load transparency film into the bypass tray Store JOB MemoryStoring a job program Delete Store Delete Deleting a job programJOB Programs Delete JOB Program Recalling a job program Recall JOB Program Select a program number from 1 to 9 using the numeric keys Copier TROUBLE? Status Messages Message Remedy First confirm the misfeed locations Misfeed RemovalMisfeed in the Rspf Remove the misfed originals Location B Location C Misfeed in the bypass tray Press the Start Key to resume copying Open the bypass tray and the side cover Misfeed in the copierMisfeed in the paper feed area Gently open the front cover Direction of the arrow to assist in removing it Misfeed in the fusing areaClose the front cover and the side cover Turn the roller rotating knob in the direction of the arrow Open and remove the misfed paper Misfeed in the center trayMisfeed in the transport area Close the side cover Misfeed in the upper paper tray Misfeed in the lower paper tray Close the lower side cover Misfeed in the upper exit areaRemove the misfed paper Open the upper exit area cover Misfeed Removal Troubleshooting Problem Solution Troubleshooting General Information Types and sizes of copy paper PaperLoading copy paper Fan the copy paper and insert it into the tray Push the paper tray firmly back into the copier ORIG. Size Enter Paper Size SET Display Contrast Changing the copy paper size in the traySpecial Function Press the Special Function key Use the and keys to select the paper size that has been set Toner Cartridge Replacement At the green label portion Cartridge as shown in the illustration. Discard the shutter Shaking the cartridge, remove the tapeClose the front cover Toner REMAINING% About the toner indicatorPress and hold the Copy key during standby or warm-up Cleaning the Platen Glass and Rspf Cleaning the Bypass Tray Paper Feed Roller Use the and keys to adjust the contrast Display Contrast AdjustmentUse the and keys to select Display Contrast and press Store the supplies in a location that is Storage of SuppliesProper storage Store copy paper in the wrapper and lying flat Specifications Printer specifications Reversing single pass feeder Rspf specifications Optional Equipment System Configuration 100 Finisher AR-FN5 N Part names Supplies Specifications102 Non-sort mode Staple sort modeFinisher functions Staple Sort Exit Center Staple sortOutput 104 Use the and keys to select Staple Sort and press the OK key Stapled to the upper right position 106 Staple cartridge replacement 107 108 Staple jam removalOpen the stapler cover Staples Misfeed removal 110 111 112 113 Misfed paper Remove any misfed paper 114Pull out the paper tray which was in use Confirm that the misfeed display has been cleared Index 115 116 Index 117 118 119 120 Regulatory Information 121 Substance PreparationX Ingredient CAS No 122 Extinguishing Media Water, CO2, foam and dry chemicals 123 124 Page Sharp Corporation