Recalling a job program, Recall JOB Program | Sharp AR-M208 instruction

JOB MEMORY

3 Select a program number from 1 to 9 using the numeric keys.

●The numbers with a check mark are program numbers which contain job programs. If a checked number is entered, the message "Delete job program?" will appear to confirm the selection to delete the program. To delete the program, select "YES" with the and keys and press the OK key.

●If "NO" is selected, the previous screen will reappear.

Recalling a job program

1 Press the PROGRAM key.

●The JOB PROGRAMS screen will appear with RECALL highlighted.

JOB PROGRAMS

RECALL

STORE

DELETE

2 Press the OK key.

●The RECALL JOB PROGRAM screen will appear.

RECALL JOB PROGRAM

1		2		3
4		5		6
7		8		9

[10-key]:SELECT

3

SPECIAL FUNCTIONS

69

Image 71

Sharp AR-M208 operation manual Recalling a job program, Recall JOB Program

Contents

AR-M208 For Your Records Making Copies Outline of this Manual Contents Contents Contents Getting Started Chapter Conventions used in this manual Introduction Safety Precautions Do not install your copier in areas that are Copier Installation Copier Installation High-quality digital image Main FeaturesSubstantial copying features High-speed laser copying Environmentally friendly design Printer featuresOptional features Scan once/ Print many Exterior Part Names and Functions Interior Operation panel Special Function key Auto Image key pSided Copy key p Output key p Dehumidification heater switch DH Power Power on and OFFPower on Power off Auto power shut-off mode Initial settingsPower save modes Preheat mode Function Icons To exit the review screen, press the Back key Function ReviewPress the JOB Status key Use the and keys to select a function Auditing Accounts How to copy in the auditing modeEnter your account number using the numeric keys Please see your key operator for assistance When copying is completed, press the Audit Clear key Getting Started Making Copies Close the platen cover Copying from Platen GlassOriginal size scale Press the Start key Set the number of copies using the numeric keysEnsure that the desired paper tray is selected Acceptable originals Using the RspfCopying from the Rspf About reversing single pass feeder Rspf Set the number of copies and press the Start key Set the originals face up in the document feeder tray Two-sided copies from one-sided originals Copy ModeUsing the Rspf TWO-SIDED Copying OK key Using the platen glassBinding Change OFF Use the and keys to select one-sided to two-sided copying Copy Mode Key again Only when a Rspf is being usedTwo-sided copies from two-sided originals Document feeder tray One-sided copies from two-sided originalsUse the and keys to select two-sided to two-sided copying Press the OK key Use the and keys to select two-sided to one-sided copying 12 to Press the Exposure key Exposure AdjustmentAuto Text, text/photo, and photo Text Use the and keys to adjust the copy density as desired Paper size Reduction ENLARGEMENT/ZOOMAutomatic selection Enter the number of copies and press the Start key Press the Auto Image key Keys to select a zoom ratio Use the and keys to select a preset copy ratio or useManual selection Press the Copy Ratio key Press the OK key Use the Paper Select key to select the desired tray Rotation Copying Unfold the bypass tray Acceptable paper for copying from the bypass trayCopying from the bypass tray Press the Paper Select key to select the bypass tray Extra Image ADJSET Copy of first original Second original Select the desired available copier functions Interrupting a Copy RUNPress the Interrupt key Set an original for interrupt copying Key to resume copying When all Interrupt copies are finished, press the InterruptUsed for interrupt copying Interrupting a Copy RUN Special Functions SORT/GROUP Copying in the sort or group modeSort mode Group mode Press the Output key SortGroup Offset stack Press the Special Function key. Then press the OK key Margin ShiftSpecial Modes Erase To select the shift amount Margin Shift OFF Down Use the and keys to select Erase and press the OK key EraseErase OFF Center Use the and keys to select the desired erase mode Dual page Copy Okoff on Special Modes Margin Shift Erase 1 or 4 Use the and keys to select the desired layout pattern OkchangeBorder no Use the and keys to select 2in1/4in1 and press the OK key Use the and keys to select a type of border line Border Use the and keys to select B/W Reverse and press the OK key ReverseXY Zoom Reverse XY Zoom Press the key Use the and keys to select XY Zoom and press the OK keyDirection 81 11R Special Modes XY Zoom Reverse Transparency Load transparency film into the bypass tray Delete JOB MemoryStoring a job program Store Delete JOB Program Deleting a job programJOB Programs Store Delete Recall JOB Program Recalling a job program Select a program number from 1 to 9 using the numeric keys Copier TROUBLE? Message Remedy Status Messages Remove the misfed originals Misfeed RemovalMisfeed in the Rspf First confirm the misfeed locations Location C Location B Press the Start Key to resume copying Misfeed in the bypass tray Gently open the front cover Misfeed in the copierMisfeed in the paper feed area Open the bypass tray and the side cover Close the front cover and the side cover Misfeed in the fusing areaDirection of the arrow to assist in removing it Turn the roller rotating knob in the direction of the arrow Close the side cover Misfeed in the center trayMisfeed in the transport area Open and remove the misfed paper Misfeed in the lower paper tray Misfeed in the upper paper tray Open the upper exit area cover Misfeed in the upper exit areaRemove the misfed paper Close the lower side cover Misfeed Removal Problem Solution Troubleshooting Troubleshooting General Information Loading copy paper PaperTypes and sizes of copy paper Push the paper tray firmly back into the copier Fan the copy paper and insert it into the tray Press the Special Function key Changing the copy paper size in the traySpecial Function ORIG. Size Enter Paper Size SET Display Contrast Use the and keys to select the paper size that has been set At the green label portion Toner Cartridge Replacement Close the front cover Shaking the cartridge, remove the tapeCartridge as shown in the illustration. Discard the shutter Press and hold the Copy key during standby or warm-up About the toner indicatorToner REMAINING% Cleaning the Platen Glass and Rspf Cleaning the Bypass Tray Paper Feed Roller Use the and keys to select Display Contrast and press Display Contrast AdjustmentUse the and keys to adjust the contrast Store copy paper in the wrapper and lying flat Storage of SuppliesProper storage Store the supplies in a location that is Specifications Reversing single pass feeder Rspf specifications Printer specifications Optional Equipment 100 System Configuration Part names Finisher AR-FN5 N 102 SpecificationsSupplies Finisher functions Staple sort modeNon-sort mode 104 Staple sortOutput Staple Sort Exit Center Stapled to the upper right position Use the and keys to select Staple Sort and press the OK key 106 107 Staple cartridge replacement Open the stapler cover Staple jam removal108 Staples 110 Misfeed removal 111 112 Misfed paper 113 Confirm that the misfeed display has been cleared 114Pull out the paper tray which was in use Remove any misfed paper 115 Index Index 116 117 118 119 Regulatory Information 120 Substance PreparationX Ingredient CAS No 121 Extinguishing Media Water, CO2, foam and dry chemicals 122 123 124 Page Sharp Corporation