Shaking the cartridge, remove the tape | Sharp AR-M208 specs

TONER CARTRIDGE REPLACEMENT

3	Remove the new toner cartridge from the bag. Grasp the cartridge on
	both sides and shake it horizontally approximately 20 times. After

shaking the cartridge, remove the tape.

NOTE:

Grasp the grip when holding the cartridge. Do not hold the cartridge by the shutter. Be sure to only shake the cartridge before the tape is removed.

Approx. 20 times

Shutter

Tape

4 Gently insert the toner cartridge along the guides until it clicks in place while pushing the lock release lever.

NOTE:

If dirt or dust is adhered to the toner cartridge, remove it before installing the cartridge.

5	Remove the tape from the shutter. Pull the shutter out of the toner
	cartridge as shown in the illustration. Discard the shutter.

5

6 Close the front cover.

GENERAL INFORMATION

91

Image 93

Sharp AR-M208 Shaking the cartridge, remove the tape, Cartridge as shown in the illustration. Discard the shutter

Contents

AR-M208 For Your Records Making Copies Outline of this Manual Contents Contents Contents Getting Started Chapter Conventions used in this manual Introduction Safety Precautions Do not install your copier in areas that are Copier Installation Copier Installation Substantial copying features Main FeaturesHigh-speed laser copying High-quality digital image Optional features Printer featuresScan once/ Print many Environmentally friendly design Exterior Part Names and Functions Interior Operation panel Sided Copy key p Auto Image key pOutput key p Special Function key Power on Power on and OFFPower off Dehumidification heater switch DH Power Power save modes Initial settingsPreheat mode Auto power shut-off mode Function Icons Press the JOB Status key Function ReviewUse the and keys to select a function To exit the review screen, press the Back key How to copy in the auditing mode Enter your account number using the numeric keysAuditing Accounts Please see your key operator for assistance When copying is completed, press the Audit Clear key Getting Started Making Copies Copying from Platen Glass Original size scaleClose the platen cover Set the number of copies using the numeric keys Ensure that the desired paper tray is selectedPress the Start key Copying from the Rspf Using the RspfAbout reversing single pass feeder Rspf Acceptable originals Set the number of copies and press the Start key Set the originals face up in the document feeder tray Using the Rspf Copy ModeTWO-SIDED Copying Two-sided copies from one-sided originals Binding Change OFF Using the platen glassUse the and keys to select one-sided to two-sided copying OK key Copy Mode Only when a Rspf is being used Two-sided copies from two-sided originalsKey again Use the and keys to select two-sided to two-sided copying One-sided copies from two-sided originalsPress the OK key Document feeder tray Use the and keys to select two-sided to one-sided copying 12 to Auto Exposure AdjustmentText, text/photo, and photo Press the Exposure key Text Use the and keys to adjust the copy density as desired Reduction ENLARGEMENT/ZOOM Automatic selectionPaper size Enter the number of copies and press the Start key Press the Auto Image key Manual selection Use the and keys to select a preset copy ratio or usePress the Copy Ratio key Keys to select a zoom ratio Press the OK key Use the Paper Select key to select the desired tray Rotation Copying Acceptable paper for copying from the bypass tray Copying from the bypass trayUnfold the bypass tray Extra Image ADJ SETPress the Paper Select key to select the bypass tray Copy of first original Second original Press the Interrupt key Interrupting a Copy RUNSet an original for interrupt copying Select the desired available copier functions When all Interrupt copies are finished, press the Interrupt Used for interrupt copyingKey to resume copying Interrupting a Copy RUN Special Functions Sort mode Copying in the sort or group modeGroup mode SORT/GROUP Sort GroupPress the Output key Offset stack Special Modes Margin ShiftErase Press the Special Function key. Then press the OK key To select the shift amount Margin Shift OFF Down Erase OFF EraseCenter Use the and keys to select Erase and press the OK key Use the and keys to select the desired erase mode Dual page Copy Okoff on Special Modes Margin Shift Erase 1 or 4 Border no OkchangeUse the and keys to select 2in1/4in1 and press the OK key Use the and keys to select the desired layout pattern Use the and keys to select a type of border line Border Reverse XY ZoomUse the and keys to select B/W Reverse and press the OK key Reverse XY Zoom Use the and keys to select XY Zoom and press the OK key DirectionPress the key 81 11R Special Modes XY Zoom Reverse Transparency Load transparency film into the bypass tray Storing a job program JOB MemoryStore Delete JOB Programs Deleting a job programStore Delete Delete JOB Program Recall JOB Program Recalling a job program Select a program number from 1 to 9 using the numeric keys Copier TROUBLE? Message Remedy Status Messages Misfeed in the Rspf Misfeed RemovalFirst confirm the misfeed locations Remove the misfed originals Location C Location B Press the Start Key to resume copying Misfeed in the bypass tray Misfeed in the paper feed area Misfeed in the copierOpen the bypass tray and the side cover Gently open the front cover Misfeed in the fusing area Direction of the arrow to assist in removing itClose the front cover and the side cover Turn the roller rotating knob in the direction of the arrow Misfeed in the transport area Misfeed in the center trayOpen and remove the misfed paper Close the side cover Misfeed in the lower paper tray Misfeed in the upper paper tray Remove the misfed paper Misfeed in the upper exit areaClose the lower side cover Open the upper exit area cover Misfeed Removal Problem Solution Troubleshooting Troubleshooting General Information Paper Types and sizes of copy paperLoading copy paper Push the paper tray firmly back into the copier Fan the copy paper and insert it into the tray Special Function Changing the copy paper size in the trayORIG. Size Enter Paper Size SET Display Contrast Press the Special Function key Use the and keys to select the paper size that has been set At the green label portion Toner Cartridge Replacement Shaking the cartridge, remove the tape Cartridge as shown in the illustration. Discard the shutterClose the front cover About the toner indicator Toner REMAINING%Press and hold the Copy key during standby or warm-up Cleaning the Platen Glass and Rspf Cleaning the Bypass Tray Paper Feed Roller Display Contrast Adjustment Use the and keys to adjust the contrastUse the and keys to select Display Contrast and press Proper storage Storage of SuppliesStore the supplies in a location that is Store copy paper in the wrapper and lying flat Specifications Reversing single pass feeder Rspf specifications Printer specifications Optional Equipment 100 System Configuration Part names Finisher AR-FN5 N Specifications Supplies102 Staple sort mode Non-sort modeFinisher functions Output Staple sortStaple Sort Exit Center 104 Stapled to the upper right position Use the and keys to select Staple Sort and press the OK key 106 107 Staple cartridge replacement Staple jam removal 108Open the stapler cover Staples 110 Misfeed removal 111 112 Misfed paper 113 Pull out the paper tray which was in use 114Remove any misfed paper Confirm that the misfeed display has been cleared 115 Index Index 116 117 118 119 Regulatory Information 120 Substance PreparationX Ingredient CAS No 121 Extinguishing Media Water, CO2, foam and dry chemicals 122 123 124 Page Sharp Corporation