Certificates and guidelines, EMC directive | Siemens PANEL PC 877

Appendix

A.1 Certificates and guidelines

A.1.1 Guidelines and declarations

A

Notes on the CE marking

The following applies to the SIMATIC product described in this documentation:

EMC directive

AC voltage supply

The devices with AC voltage supply fulfill the requirements of the EC directive "89/336/EEC Electromagnetic Compatibility" and are intended for the following fields of application in accordance to the CE marking.

Area of application	Requirement for
	Emitted interference	Noise immunity
Industry	EN 61000-6-4: 2001	EN 61000-6-2: 2001

The device is also compliant with EN 61000-3-2:2000, harmonic currents and EN 61000-3- 3:1995, voltage fluctuation and flicker.

DC power supply

This devices with DC power supply fulfill the requirements of the EC directive "89/336/EEC Electromagnetic Compatibility" and are intended for the following fields of application in accordance to the CE marking.

Area of application	Requirement for
	Emitted interference	Noise immunity
Industry	EN 61000-6-4: 2001	EN 61000-6-2: 2001

The device is also compliant with EN 61000-3-2:2000, harmonic currents and EN 61000-3- 3:1995, voltage fluctuation and flicker.

SIMATIC Panel PC 877	A-1
Operating instructions, Release 07/2006, A5E00877780-01

Image 261

Siemens PANEL PC 877 Certificates and guidelines, Guidelines and declarations, EMC directive, AC voltage supply

Contents

Operating Instructions Edition 07/2006 SimaticPage Operating instructions Release 07/2006 Industrial PC Simatic Panel PC Qualified Personnel Safety GuidelinesPrescribed Usage Trademarks Table of contents 10-1 Table of contents 11-1 15-1 14-116-1 17-1 Glossary-1 Viii Overview Foreword Conventions Position in the information landscapeTrademarks Representation Validity Safety information Safety informationEmergencies System expansions Electrical connectionHigh frequency radiation Unintentional operating situations Repairs Handling and disposal of lithium batteries General information OverviewTransport Tools & downloads Safety-relevant applicationsProcessor and optical drive Chemical stability Sources of light Defective pixels in the displayBurn-in dffect on TFT displays Design DescriptionDesign Brief description Touch screen variants Keyboard variants General features Technical features DVD-ROM Configuration options Accessories Comment Order No AccessoriesRemote Kit order version Remote Kit, 24V DC, 30m Description Accessories Application planning IntroductionField of application Unpacking and checking the delivery Procedure Identification Number Device identification data Mounting Positions and Fastening Installation guidelines Application planning 4.4 Mounting Positions and Fastening Permitted mounting positions ApprovalPermitted mounting positions Type of fixation Principle Protection against dust and waterIP65 degree of protection and NEMA4 IP54 degree of protection Preparing the mounting cut-out Mounting cut-out S53 Preparing the mounting cut-outTolerance Steps for preparing the mounting cut-out Mounting depth of the device Panel PC with operator UnitsAdditional mounting depth with optical drive Installing the device according to EMC directive EMC directiveElectromagnetic compatibility Rack installation InstallationSwivel arm installation Switchgear cabinet installation IP 65 degree of protection Drilling holes Securing the device with screwsRisk of damage Steps for drilling holes Steps for fastening the device with screws IP 54 degree of protection Observe the panel seal when mounting Installation Securing the device with screws Connection and operator control components Connecting Reset button On / Off switchData loss Connection components of the control unit Guarantee for the IP 65 degree of protectionUse of USB devices USB connection control unit Item Name General connection information Connecting the 100 V to 240 V AC power supply Connecting the power supply Power Factor CorrectionPower consumption Country-specific connection information Power supply Connecting the 24 V DC power supplyConnecting the protective conductor Steps for connecting the device to the 24 V DC power supply Connecting the equipotential bonding circuit Connecting the equipotential bonding circuitSteps for connecting the equipotential bonding Connecting Connecting the equipotential bonding circuit Integration into an automation system EthernetAdditional information 1 MPI/PROFIBUS-DP network Device in a Simatic S7 configuration Coupling Connecting an S7 automation systemHardware requirements Risk of damage to the device Networking via Industrial Ethernet Checklist CommissioningRequirements Self Test Switch on the device Setting up the Microsoft Windows operating system Additional hardware and software components Installing applications and drivers Screen keyboard Setting the touch screen Touch screen panel, end Panel Wizard Keyboard panel, end Panel Wizard Setting the key panel Commissioning Installing applications and drivers Bios settings Microsoft Windows operating system Enables Windows 2000 Professional Service packRestrictions Automatic logon Windows XP Professional Using USB peripherals USBUSB interface Commissioning 8.7 USB Operation and configuration Switch on the deviceNormal operation Risk of data loss Operation and configuration 9.1 Normal operation Switching off the device Overview Additional Drivers and Applications Function Calibrating the touch screen, Updd Maloperation Procedure Enable/disable touch functionality No. Procedure Windows Security Center Windows XP Professional only Function Default setting Alert Settings Dialog Alarms KeyTools for key panel devices only Calling up KeyToolsMalfunctions of the user software Calling up TouchInput Screen keyboard for touch panel device only Start Setbrightness Scope CheckLanguageID Multilingual settings for the operating system Page DVD ROM/CD RW Data may be corrupted when burning CD-R or CD-RWBurner/DVD player software Information on burning CD-Rs/CD-RWs USB keyboard controller Simatic Panel PC Status displays Operation On / Off switch Description On / Off switchReset button Description General control elements Device with key panel Using the keyboard Function keysSoftkeys Control keys Toggling between lower-case and upper-case letters Alphanumeric keys Enter special characters, arithmetic signs and signs Numeric keys Cursor keys External keyboards Functionality Using the direct control key moduleSoftware control Mounting Keys Keyboard code ExampleSHIFT+F1 SHIFT+F8 SHIFT+F9 SHIFT+F12 KeyPad Changing the defaults Explanation Labelling function keys and softkeys Area of applicationLabeling 10-15 11 Integrated mouse Using the integrated mouse 12 Example of a 15 touch screen front Device with touch screen Using the touch screen Diskette types Disk drive Transferring authorizations Functions Safecard on Motherboard SOM Safecard On Motherboard with three temperature sensors Functions Temperature monitoring Temperature monitoringResponse Option Watchdog WD WD reactionsWD monitor times TWD Fan monitoring Scope of maintenance Maintenance and serviceCleaning agents Maximum dust content in the air circulating in the cabinet Chemical stability Procedure for cleaning the device Replacement part Replacement parts Separating the control unit from the computer unit Separating the control unit from the computer unit 12-5 Separating the device in an uninstalled state Position Bend dimensionMounting operator control unit on computer unit Repairs Installing and removing hardware componentsCarrying out repairs Limitation of Liability Preparation Open the device Steps for opening the device Open the device Installing and removing memory modules Memory expansionSlot Maximum expansion Displaying the memory configuration Installing a memory moduleHow to install a memory module How to remove a memory module Installing PCI / AT cards Installing / removing expansion modules Preparation Installing expansion modulesHow to install an expansion module PCI / AT format Inserting the slider How to install a module holding-down device Exchanging the RAID controller PCI card Introduction Disk drives DVD-ROM/CD-RW drive bay Pos DescriptionHard disk drive bay for one 3.5 drive Pos Description Drive bay for floppy disk drive Pos Description Drive bays for two 2.5 hard disks Pos Description Installing / removing a drive bay Preparations Remove the hard disk baySteps for removing the drive bay Steps for removing the floppy disk drive bay Removing drive bays for floppy disk drives 12-20 Installing and removing the optical drive Removing and installing an optical drive Procedure Loosen the 2 screws 1 of the drive housing 12-23 Removed hard disk Removing and installing a 3.5 hard disk Procedure Replacing the backup battery To be noted before you replace the batteryDisposal Replacing the battery Reconfiguring the Bios SetupSteps for replacing the battery Removing/Installing the Power Supply Removing the power supply moduleHow to remove the power supply module 12-28 General installation procedure Installing SoftwareRecovery CD Restore DVD Setting up partitions Setting up the partitions for Windows operating systems Parameter overview Format primary partition Compatibility of the Restore DVD Restoring the factory state wih the installed drive Restoring the factory state with an external USB CD/DVD ROM USB Legacy Keyboard/Mouse enabled Operating system not installed Installing Microsoft Windows operating systems Booting from the Recovery CD 12-37 Maintenance and service 12.5 Installing Software Installing individual drivers Operation of two hard disks Booting from the slave hard disk12.5.7.1 2 HDD system Hard disk Controller designation RAID 1 system Functions for RAID system management Comments about faults Configuring a RAID 1 system PrerequisitesInput delay Bios messages during startup Installing the RAID Controller software Installing burner and DVD software Backing up the hard disk Date errors writing to CD-RW Boot error messages Alarm, error and system messagesOn-screen error messages On-screen error message Meaning / suggestions Alarm, error and system messages 13.1 Boot error messages Beep tones Hex code Introduction to the Bios beep codesBBB Bbbb BBB Special code Meaning Special codes Bios beep codes Hex Meaning Description Remedy CodeCodes Special codes Troubleshooting/FAQs General problemsProblem Possible causes To correct or avoid error Problems when Using Modules of Third-party Manufacturers Temperature limits CauseRemedy 14-4 Technical data General technical dataGeneral technical data General technical data Electromagnetic compatibility EMC Climatic conditionsMechanical environmental conditions General technical data Motherboard Disk drivesInterfaces Display Status displays on the device Weight Power losses Approvals General technical data SafetyConformity Bad pixels Permissible number Panel PC Standard system Power requirements of the components Power Good Signal of the AC power supply Technical dataDevice with AC voltage supply Output voltages Power Good Signal of the DC power supply Device with DC voltage supplyVoltage Max. current Keyboard table Key codesCode Hex Check-box Display/function Name Code Hex Check-box Display/function 15-13 15-14 15-15 15-16 15-17 15-18 Panel PC 877 dimensional drawing Dimension drawings Control unit Touch screen front12 TFT 15 TFT 19 TFT AT module 16-4 Detailed descriptions MotherboardStructure and functions of the motherboard Component Description Characteristics Interface Technical features of the motherboard 17-3 Interfaces Position of the ports on the motherboard Interface Positio External interfacesProfibus MPI Serial interface COM 1 Serial interface COM 2 has the following pinout COM 2 serial interface V24/Mouse LPT1 parallel interface PS/2 mouse interface PS/2 keyboard interfaceUSB interfaces PROFIBUS/MPI interface TD+ Ethernet RJ45 connectionRD+ Symr DVI interface PinNo Abbreviation Meaning Input/Output DVI interface Interface Position Connector Description Front interfacesDisplay interfaces Pin No Abbreviation Meaning Input/Output Display interface 1st Lvds channel Display interface 2nd Lvds channel Front interface for operator panels Display type Assignment of the display to the display select pins Pin assignment of the internal interfaces Internal interfaces Interface Position Connector Connection for optical drive Pin No Abbreviation Meaning Interface to floppy disk drive Pinout of the main fan power supply Pinout of the CPU fan power supplyConnector for back-up battery Connection for On / Off switch connector Pinout of the USB 2.0 interface Pinout of the internal USB interface connectorUSB3 USB3M USB5 USB5M USB3P USB5P GND USB5 USB5M USB5P GND Layout and principle of operation Bus board Assignment of the PCI IRQ channels to the PCI slots Assignment of the PCI IRQ channels to the PCI slotsBox PC 840 PCI modules interrupt assignment PCI IRQ INT a A6 Channel Setting up a reserved interrupt on the device Assigning a reserved interrupt in the Bios SetupExclusive PCI hardware interrupt Pin No Abbreviation Type ISA slot pin assignment DACK0 Memr DRQ Sbhe MEMCS16Memw DACK5 Operating system licenses Simatic S7 cable for MPI/DP Cables Currently allocated system resources System resources 17.5.2.1 I/O address allocation System resources used by the BIOS/DOS ECP LPT SOM0CFB 0CFC 0CFF Interrupt Assignments Interrupt Description CommentPCI devices interrupt assignment PCI IRQ Memory address assignments Bios setup Bios Setup programChanging the device configuration Starting Bios Setup Starting Bios Setup 3RZHU RRW 9HUVLRQ Bios setup menus Menu Menu layout $GYDQFHG 6HFXULW\ 3RZHU RRW 9HUVLRQ Main menu System time and date Settings in the main menuFloppy disk a Floppy disk drive Array 17-42 Array Meaning Bios setup Memory Cache field Memory cache field Boot options field Example of a summary screen Keyboard features field Hardware Options submenu Example Hardware options field Entry Meaning PC is switched off and on againPCI-MPI/DP CRT / LCD 17-50 6HFXULW\ 3RZHU RRW 9HUVLRQ Advanced menu Settings in the Advanced menu DOSOther PCI AGP Device configuration submenu Configurable mode PropertiesInternal printer port LPT1 12 PCI configuration submenu example PCI configuration submenu Or its application requires it PCI Devices field 545HVRXUFHFOXVLRQ IRQ resource exclusion submenu Box PC PCI modules interrupt assignment PCI IRQ PCI IRQ channels field 16 Security menu Security menu 17-60 17 Power menu Example Power menu 18 Boot Menu Boot menu 17-63 20 Version menu Example Version menu Exit menu Documenting your device configuration Bios setup default settingsBios Setup default settings System parameters Defaults Custom entries Main Device Configuration Keyboard FeaturesPCI Configuration PCI Device Slot Hardware Options Boot SATA/PATA ConfigurationSecurity Version Certificates and guidelines DC power supplyGuidelines and declarations EMC directive Low-voltage directive Connecting peripheralsDeclaration of conformity Design guidelines Certificates and approvals SafetyDIN ISO 9001 certificate Software License Agreement EMC Electrostatic charging of individuals Additional support Service & Support on the InternetTraining center Technical Support What does ESD mean? ESD guideline Handling ESD modules Precautions against electrostatic dischargeMeasuring and modifying ESD components Shipping ESD modules Abbreviations PPIPLC TCP/IP USB VGA List of abbreviations / acronyms C.1 Abbreviations Glossary Configuration software Configuration filesCache Chipset Disc-at-once Device configurationDrivers Energy management Hard disks Gender changerHot swapping Hub License key Legacy USB supportLicense key diskette LPT interface Packet writing Operating systemPC card PC/104 / PC/104-Plus Pixel ResetPlug&Play PXE server Troubleshooting Setup Bios SetupScsi interface Session at once Wlan Windows Glossary-10 CD-R / CD-RW Index Index Index Index Index Index Index-7 Siemens AG