Saving and recalling the system settings (System Memory)
y
•If you select “Zone2”, “Zone3”, or “Zone4” in step 3, you can select “Memory1” to “Memory4”. You can save the parameters for the selected zone only when the zone is turned on.
•If system settings are already saved in the selected memory number, this unit overwrite to old system settings.
•If you save the system settings to “Memory1” to “Memory4”, you can load the stored settings by pressing the corresponding 7SYSTEM MEMORY buttons (see page 118).
6Press 9k / n repeatedly to select the group of parameters and then press 9ENTER to select or
clear the checkbox of the group.
This unit saves the parameters in the checked groups. Refer to “Saved parameters for the main zone” on page 117.
| ||||
|
| |||
| ✓ | |||
✓ |
| |||
| ||||
✓ | ||||
✓ | ||||
✓ | ||||
|
|
| ||
Current selected group of the parameters appears in red
Note
If the selected zone is other than “Main”, you can select “Input”, “Volume”, and “Tone Control”. See page 117 for details.
7Press 9n repeatedly to select “Save” and then
9ENTER to save the current system settings to the selected memory number.
|
| |
| ✓ | |
✓ | ||
✓ | ||
✓ | ||
✓ | ||
|
y
You can cancel the saving by pressing 9l.
8Press IMENU again to exit from the GUI menu.
Use this feature to rename the stored settings. The name of each memory number appears in the GUI menu or front panel display.
1Press IMENU on the remote control.
The top menu appears in the video monitor.
2Press 9k / n repeatedly to select “System Memory” and then press 9h.
The “System Memory” menu appears in the video monitor.
3Press 9k / n repeatedly to select the desired zone and then press 9h.
In the following example, “Main” is selected.
4Press 9k / n repeatedly to select “Main Rename” (example) and then 9h.
The list of the memory number appears in the video monitor.
5Press 9k / n repeatedly to select the desired memory number and then 9h.
The rename display appears in the video monitor.
|
|
|
|
|
|
| ||
|
|
|
|
|
| |||
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6Press 9ENTER repeatedly to select a character type
(CAPITAL/SMALL/LATIN CAPITAL/LATIN SMALL/ FIGURE/MARK).
7Press 9k / n to select the character you want to use and 9l / h to move to the next one.
•You can use up to 9 characters for each memory.
•Press 9n to change the character in the following order, or press 9k to go in the reverse order:
CAPITAL | A to Z, space | |
SMALL | a to z, space | |
LATIN CAPITAL | Ä, Ö, Ü, etc. | |
LATIN SMALL | ä, ö, ü, etc. | |
FIGURE | 0 to 9, space | |
MARK | !, #, %, &, etc. | |
• Press 9ENTER to switch between character types.
y
Press 9h repeatedly to select “RESET” and then press 9ENTER to set the name of the memory to the initial name.
Notes
•The character types you can select differ depending on the setting in “Language” (see page 114).
•If you set “Language” to “
”, you can also select Japanese characters.