Yamaha S30 109

QED’Level)

Pan RevSend

■Point

When the Mode (see earlier) has been set to “split,” this sets the split point. The actual note of the split point will be assigned to the upper section.

You can also select the split point by pressing the note while holding down the [SHIFT] key.

❏Settings: C-2 ~ G8

Master keyboard setting list (on split/layer)

		Split				Layer

Prameter Name	Zone1	Zone2	Zone3	Zone4	Zone1	Zone2	Zone3	Zone4
TrnsCh	ch	ch+1	ch	ch	ch	ch+1	ch	ch
TG	on	on	off	off	on	on	off	off
MIDI	on	on	off	off	on	on	off	off
Octave	+0	+0	+0	+0	+0	+0	+0	+0
Transpose	+0	+0	+0	+0	+0	+0	+0	+0
Note Limit Low	C-2	p	C-2	C-2	C-2	C-2	C-2	C-2
Note Limit High	p	G8	G8	G8	G8	G8	G8	G8
Transmit Switch PB	on	on	on	on	on	on	on	on
Transmit Switch MW	on	on	on	on	on	on	on	on
Transmit Switch KnobA-C	on	on	on	on	on	on	on	on
Transmit Switch Knob1/2	on	on	on	on	on	on	on	on
Transmit Switch FC	on	on	on	on	on	on	on	on
Transmit Switch AT	on	on	on	on	on	on	on	on
Transmit Switch FS	on	on	on	on	on	on	on	on
Transmit Switch Vol	on	on	on	on	on	on	on	on
Transmit Switch Pan	on	on	on	on	on	on	on	on
Transmit Switch Bank Select	off	off	off	off	off	off	off	off
Transmit Switch Program Change	off	off	off	off	off	off	off	off
Transmit Preset Volume	100	100	100	100	100	100	100	100
Transmit Preset Pan	C	C	C	C	C	C	C	C
Transmit Preset Bank MSB	0	0	0	0	0	0	0	0
Transmit Preset Bank LSB	0	0	0	0	0	0	0	0
Transmit Preset PC	0	0	0	0	0	0	0	0
CS Control Number Assign	7	7	7	7	7	7	7	7

ch: Keyboard transmit channel

p:split point

Details about each parameter are given on page 121

For more information about the master keyboard mode, refer to page 52 in Basics Section.

Common Quick Edit

You can set various parameters governing the sonic properties of the Layer Part, The following four screens are only available when the Layer switch (Page 117) for each Part is set to on.

QED Level (Quick Edit Level)

QED EF (Quick Edit Effect)

QED Filter (Quick Edit Filter)

QED EG (Quick Edit Envelope Generator)

QED Level (Quick Edit Level)

You can set output level and pan parameters for each Layer Part. The settings are also available in the Part Edit screens.

■Vol (Volume)

Set the output level of the Layer Part.

❏Settings: 0 ~ 127

■Pan

Set the stereo pan position of the Layer Part.

❏Settings: L63 (Left) ~ C (Center) ~ R63(Right)

■RevSend (Reverb Send)

Set the Send level of the signal sent from Insertion Effect 1/2 (or the by-passed signal) to the Reverb effect.

❏Settings: 0 ~ 127

■ChoSend (Chorus Send)

Set the Send level of the signal sent from Insertion Effect 1/2 (or the by-passed signal) to the Chorus effect.

❏Settings: 0 ~ 127

QED EF (Quick Edit Effect)

You can set the amount of Chorus applied to the Layer Part, as well as Portamento settings.


QED’EF)	Chorus	Portamento-Time
Common	-63	off	127

■Chorus

Set the Return level of the Chorus effect as an offset value.

❏Settings: -64 ~ 0 ~ +63

■Portamento

Switch Portamento on or off.

❏Settings: off, on

■Time

Set the pitch transition time. Higher values mean longer transition times.

❏Settings: -64 ~ 0 ~ +63

Performance Mode

109