Mode Utility
MIDI (System MIDI)
You can set overall MIDI parameters for the system. The following five screens are available.
MIDI Ch (MIDI Channel)
MIDI Arp (MIDI Arpeggio)
MIDI Sw (MIDI Receive Switch)
MIDI Other
MIDI GM/XG Receive
MIDI Ch (MIDI Channel)
Set the MIDI Channel parameters.
|
|
|
|
|
|
|
| MIDI Ch) | Recv | Trans | Local | DevNo | |
| Sys | omni | 1 | on | all |
|
|
|
|
|
|
|
|
■Recv (Basic Receive Channel)
Set the MIDI Receive channel for using the synthesizer with an external sequencer, computer and so on, and for using it as a MIDI tone generator.
❏Settings: 1 ~ 16, omni (all channels), off
■Trans (Keyboard Transmit Channel)
Set the MIDI Transmit channel for transmitting MIDI from the keyboard, controllers and so on.
❏Settings: Ch1 ~ Ch16, off
■Local (Local On/Off)
If you set Local to “off,” the keyboard and controllers are internally disconnected from the synthesizer’s tone generator section so that no sound is output when you play the keyboard or use the controllers. However, the data will be transmitted through the MIDI OUT. Also, the tone generator section will respond to messages received at the MIDI IN.
❏Settings: off on,
■DevNo (Device Number)
Set the MIDI Device Number. This number must match the Device Number of the external MIDI device when transmitting/receiving bulk data, parameter changes or other system exclusive messages to/from it.
❏Settings: 1 ~ 16, all, off
MIDI Arp (MIDI Arpeggio)
Set the arpeggiator’s MIDI parameters.
|
|
|
|
|
|
|
|
| MIDI | Arp) | Switch | Hold | Out(Vce)Ch(Vce) | ||
| Sys[ |
| ] 67 | 68 | off | 16 |
|
|
|
|
|
|
|
|
|
■Switch
Select the Control Change Number used to control the ARPEGGIO [ON/OFF] key.
❏Settings: 000 ~ 095 (000, 032 = off)
■Hold
Select the Control Change Number used to control the ARPEGGIO [HOLD] key.
❏Settings: 000 ~ 095 (000/032 = off)
■Out (Vce)
Enable/disable the output or Arpeggiator data to external MIDI devices through the MIDI Out.
❏Settings: off (disabled), on (enabled)
■Ch (Vce) (Arpeggio Transmit Channel) Select the MIDI channel through which Arpeggio data will be sent.
❏Settings: 1 ~ 16
MIDI Sw (MIDI Receive Switch)
Set the MIDI Receive parameters.
|
|
|
|
|
|
|
| MIDI Sw)RcvBulk | BankSel | PgmChng | Control | ||
| Sys | on | perform | off | mode1 |
|
|
|
|
|
|
|
|
■RcvBulk (Receive Bulk)
Select whether or not Bulk Dump data can be received.
❏Settings: protect (off), on
■BankSel (Bank Select)
Set to enable or disable transmission and reception of Bank Select messages between the instrument and an external MIDI device. With any setting other than “off,” the instrument can receive a Bank Select massage coming in, and it can also send a Bank Select massage out to an external MIDI device when you select a Bank using a MEMORY key or the like on its front panel.
❏Settings: off, all, part, perform off:
Ignores (does not receive) a Bank Select message. The instrument does not send this message, either.
all:
Receives all Bank Select messages coming in. When the instrument receives only a Program Change message in Performance Mode, that message selects a Part’s Voice.
part:
Receives only Bank Select messages for selecting a Voice Bank, whichever mode you are working in.
perform:
Receives only Bank Select messages for selecting a Performance Bank when you are working in Performance Mode. When you are working in Voice Mode, the instrument only receives Bank Select messages for selecting a Voice Bank.
130