offset (Velocity Offset)

As illustrated below, the velocity will be increased by the specified amount.

Changes to velocity curve according to VelDepth (with offset set to 64)

Velocity at

tone generator Depth=64

■ Mode

Select whether each Part is played back

monophonically (single notes only) or

polyphonically (multiple simultaneous notes).

This parameter is only available for Normal Voice Parts

1 to 16 and Plug-in Part.

❏ Settings: mono, poly

Offset=96

Depth=64

Offset=127

Offset=64

■ Arp (Arpeggio switch)

Switch the Arpeggiator for the currently selected

Part on or off.

Offset=96

 

Depends on

Depth=64

 

 

offset

Offset=32

 

 

Offset=64

 

Depends on

 

 

 

 

 

Velocity=1

 

offset

Received

 

 

 

 

 

 

Velocity

 

 

 

 

Offset=-32

Part Layer

You can set various MIDI parameters for each Part, including MIDI Receive Channel, Arpeggiator switch, note limit and velocity. These parameters are largely used when layering multiple Parts. The following four screens are available.

LYR Mode (Layer Mode)

LYR Limit (Layer Limit)

LYR Tune (Layer Tune)

LYR Out (Layer Out)

This parameter is not available for Multi Plug-in Parts.

❏ Settings: off, on

■ Layer (Layer switch)

When switched on, you can layer up to four Parts.

This parameter in not available for Multi Plug-in Parts.

❏ Settings: off, on

You can also set the overall output level and stereo pan position of the Layer when this is switched on (Page 104).

Layers may be slow to sound, depending on their component Parts.

If you turn five or more Layer Switches “on”, only four Parts are enabled for the layer. These four Parts are determined in the priority of Part01 to Part16, PartPL. For disabled Parts, their Layer switch values will be shown in brackets like “(on).”

■RcvCh (MIDI Receive Channel)

Set the MIDI Receive Channel for each Part. Select “off” for Parts that you do not want to respond to MIDI.

❏ Settings: 1 ~ 16, off

Performance Mode

LYR Mode (Layer Mode)

You can set the method by which each Part is output. The parameters will vary according to the Part selected.

Part 1 to 16

Plug-in Part

 

 

 

 

 

 

 

 

LYR’Mode)

Mode

Arp

Layer

RcvCh￿

 

 

Part01

poly

on

off

1

 

 

 

 

 

 

 

 

Drum Voice Part

 

 

 

 

 

 

 

 

 

LYR’Mode)

Arp

Layer

RcvCh

￿

 

 

Part01

on

off

1

 

 

 

 

 

 

 

 

Multi Plug-in Part

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LYR’Mode)

 

 

RcvCh

￿

 

 

Part17

 

 

1

 

 

 

 

 

 

 

 

LYR Limit (Layer Limit)

You can set note ranges and velocity limits for each Part.

 

 

 

 

 

 

LYR’Limit)

Note Limit

Vel Limit

￿

 

Part01

C-2 - G 8

1 - 127

 

 

 

 

 

 

■Note Limit

Set the lowest and highest notes of the keyboard range for each Part. Each Part will only sound for notes played within its specified range.

❏ Settings: C-2 ~ G8 (for the lowest and highest notes)

If you specify the highest note first and the lowest note second, for example “C5 to C4,” then the note range covered will be “C-2 to C4” and “C5 to G8.”

You can set the lowest and highest notes in the range by pressing notes on the keyboard while holding down the [SHIFT] key.

117