Basics Section
1Press the [UTILITY] key to enter Utility Mode.
MODE
VOICE 
PERFORM STORE
UTILITY CARD SEQ
PLAY
EDIT | JOB | PLAY/ | |
STOP | |||
|
| ||
COMPARE |
|
| |
|
|
| |
|
|
|
2Use the [PAGE] knob to switch to the CTRL Other (System Control Other) screen.
|
| CTRL Other) | FS |
|
|
|
| |
|
| Sys |
| 088[ |
|
|
| |
SHIFT | PAGE | A | B |
| C | 1 | 2 | DATA |
PART/ELEMENT
3Use Knob [B] to select “099:PC Inc” (Program Change Increment).
|
| CTRL Other) | FS |
|
|
| |
|
| Sys |
| 099[PC Inc | ] |
|
|
SHIFT | PAGE | A | B | C | 1 | 2 | DATA |
PART/ELEMENT
In Voice/Performance Mode, the Foot Switch can now be used to switch between programs.
Alternatively, you can assign other functions such as Arpeggio Switch (On/Off), Sequencer (Play/Stop) and so on (Page 129).
Using Knob [1]/[2] To Control the Arpeggio
You can assign Arpeggiator ON/OFF and Hold functions to Knob [1]/[2] (Performance Mode). The following is an explanation of how to do this. In the example, we use Internal Performance 075 (E11), and assign Arpeggio Hold to Knob [1] and Arpeggio ON/OFF to Knob [2].
1Press the [UTILITY] key to enter Utility Mode.
2Use the [PAGE] knob to switch to the MIDI Arp screen.
44
3Use Knob [B] to assign the Control Change Number for Arpeggio ON/OFF, which is 90 here. Similarly, use Knob [C] and set the Control Change Number to 89 to assign Arpeggio Hold to Knob [1].
|
| MIDI Arp) | Switch | Hold Out(Vce)Ch(Vce) |
| ||
|
| Sys[ | ] 90 | 89 | off | 16 |
|
SHIFT | PAGE | A | B | C | 1 | 2 | DATA |
PART/ELEMENT
4Press the [PERFORM] key to enter Performance Mode.
5Select Internal Performance 075 (E11), then enter Performance Edit Mode by pressing the [EDIT] key.
6Turn Knob [A] until “Common” is displayed at the bottom left of the screen.
7Use the [PAGE] knob to switch to the CTL Assign1 screen.
8Turn Knobs [1]/[2] to set their parameters to the same values as the Control Change Numbers set in Step 3. That is, assign a value of 89 to Knob [1] and a value of 90 to Knob [2].
|
| CTL’Assign1) |
| BC | Knob1 | Knob2 |
| |
|
| Common [FootCtrl] |
| 02 | 89 | 90 |
| |
SHIFT | PAGE | A | B | C |
| 1 | 2 | DATA |
PART/ELEMENT
9Store the edited Performance (Page 124).
Now, for Internal Performance 075 (E11), Arpeggio Hold is assigned to Knob [1] and Arpeggio ON/OFF to Knob [2]. If you select this Performance in Performance Play Mode, turning each knob left or right will switch its respective parameter off or on, respectively. (The Arpeggiator responds to notes below C3 on the keyboard.)
If you do not wish to control the Destination parameter of the Voice, enter Performance Edit Mode, switch to the RCV Sw2 screen of Performance Part Edit, then set the parameters for Knobs [1] and [2] to “off.”
In Performance Mode, to use the Arpeggiator for Parts which have their Layer parameter (Layer Switch) set to “on,” their Arp parameter (Arpeggio Switch) also has to be set to “on.” (Page 117)