Zoom MRS-1266 TYPE, TYPE, US-DRV, FLANGER, to edit, that key lights up, 3. Press the [EDIT] key, effect module that you want to edit

Reference [Effects]

1. Press the [EFFECT] key in the display section sothat key lights up.

The currently selected patch appears on the display.

2. Use the ALGORITHM keys to select an algorithm,

and turn the dial to select the patch that you want

to edit.

It is not possible to change the algorithm of a patch. For this reason, you must first begin by selecting a patch that uses the desired algorithm, even when you want to create a patch from scratch.

HINT

The indication “EMPTY” appears instead of the patch name if the patch is empty. To create a patch from scratch, select an empty patch in the desired algorithm.

3. Press the [EDIT] key.

The first line of the display will indicate “EDIT”. This means

that the patch can now be edited.

TYPE

US-DRV4. From the [MODULE] keys, press the key for theeffect module that you want to edit.

HINT

•The lit/out condition of the [COMPRESSOR], [PRE AMP/ DRIVE], [EQUALIZER], and [MODULATION/DELAY] keys indicates the on/off status of the corresponding module. Each time you press one of these keys, the setting will be toggled. (If you select an effect module that is off, the display will indicate “-OFF-”.)

•To edit a patch of the DUAL algorithm, set the channel to on/off with the [PRE AMP/DRIVE] and [EQUALIZER] keys, and then use the cursor up/down keys to select the module.

•To edit the ZNR or VOL PDL modules, press the [TOTAL] key, and then use the cursor up/down keys to display either “ZNR” or “VOL PDL”. Then turn the dial to edit the parameter.

5. If you want to switch the effect type for the selected module, press the cursor up key to make the display show “TYPE”, and then turn the dial to select the desired effect type.

If you select an effect module other than [TOTAL], use the cursor up/down keys to call up the effect parameter setting screen for that effect type.

TYPE

FLANGER

When editing a patch, use the [MODULE] keys to select the				HINT
module for editing. The	table below	shows how the		If the contents of a patch have been edited, the “EDIT” indi-
				cator in the upper part of the display will change to “EDIT-
[MODULE] keys correspond to the various effect modules.
				ED”.
Key
Algorithm
Mic & Mic	DUAL TYPE	L ch	R ch	__	ZNR	VOL PDL	PAT LVL
		ON/OFF	ON/OFF
	DUAL TYPE	L ch	R ch	__	ZNR	VOL PDL	PAT LVL
		ON/OFF	ON/OFF
G/B & Mic
		L ch	R ch
DUAL	DUAL TYPE			__	ZNR	VOL PDL	PAT LVL
		ON/OFF	ON/OFF
	DUAL TYPE	L ch	R ch	__	ZNR	VOL PDL	PAT LVL
		ON/OFF	ON/OFF
Gtr & Bass
		L ch	R ch
	DUAL TYPE			__	ZNR	VOL PDL	PAT LVL
		ON/OFF	ON/OFF
GUITAR/BASS	COMP	PRE AMP/	EQ	MODULATION/	ZNR	VOL PDL	PAT LVL
		DRIVE		DELAY
MIC	COMP/LIM	MIC PRE +	EQ	MODULATION/	ZNR	VOL PDL	PAT LVL
		DE-ESSER		DELAY
LINE	COMP/LIM	ISOLATOR	EQ	MODULATION/	ZNR	VOL PDL	PAT LVL
MASTERING	3BAND COMP/	NORMALIZE	EQ	DIMENSION/	ZNR	VOL PDL	PAT LVL
	LO-FI			RESONANCE

ZOOM MRS-1266

122