Rover 51 Removing the Drive Frame Cover, Replacing the Drive Frame Cover, Drive Chain Lubrication

Page 10

ENGLISH

MAINTENANCE (Continued)

Adjusting the Drive Cable (Continued)

•Start the mower in the disengaged position.

•Push the drive bale forward until the gap between the bale and the handle bar is 55mm (refer figure 12).

•The drive should just begin to engage at this point.

•If the drive is not beginning to engage, rotate the thumb wheel on the cable support block (one click at a time) in an anti clockwise direction until it does (refer figure 13).

•If the drive engages and drives off at a gap greater than 55mm rotate the thumb wheel on the cable support block one click at a time in the clockwise direction until it does (refer figure 13).

•Test the mower at all speeds ensuring that it self disengages when the drive bale is released and that the transmission does not slip at full speed with the drive bale fully engaged.

•If you still experience problems, see your nearest authorised Rover dealer.

•Ensure the cable is not damaged or kinked which may affect the drive.

•Apply a drop of lubricant to the pivot points of the drive bale to ensure smooth and safe operation.

Removing the Drive Frame Cover

•Unscrew the front and rear phillips head screw in that order (refer figure 14).

•Lift the cover and rotate out of the mower to expose the upper transmission components.

Blow grass and dirt out of the recessed holes to expose the head of the fixings.

™

12

13Anti-clockwise

14

Replacing the Drive Frame Cover

 

• Make sure the raised ring on the brass section of the drive cable nests into the groove of the lower drive support frame and fit the

 

lid accurately on top before screwing down the cover.

CAUTION

• Do not operate the transmission bale with the cover loose or removed as you will damage the lower drive support frame.

 

•Fit the drive cable into its retaining slot in the lower drive support frame and hold it down horizontally with one hand

(refer figure 15).

•Rotate the cover into position over the cable until it seats properly and maintain pressure on the lid above the cable.

•Screw the rear fixing above the cable down firmly.

•Screw the forward fixing down firmly.

Leave the fixings in the lid when removing or replacing.

15

Drive Chain Lubrication

 

• Refer to the “Warning” and “Caution” notes at the beginning of the maintenance section.

 

• Do not apply excessive lubricant to the chain as it may flick off and onto the drive clutches during operation.

WARNING

• Keep lubricant clear of the drive clutches.

 

•Remove the drive frame cover (refer to the “Removing the Drive Frame Cover” section) to expose the drive chain.

•While rotating the outer clutch plate (clockwise) apply an even spread of suitable (non aerosol) chain lubricant along

the length of the chain (refer figure 16).

•Replace the drive frame cover (refer to the “Replacing the Drive Frame Cover” section).

Put the chain lubricant in a container with a long pointed spout to make application easier. Apply a little of the lubricant on the cams between the clutch engagement lever and the outboard output shaft bearing retainer while lubricating the chain.

16

7

Powered Walk Behind Mower - CE

Part No. 04016218 Rev G

© Copyright 12/2006

 

 

 

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Powered Walk Behind Mower CE Part No Rev G Macchina List of symbols and their meanings are shown belowAttenzione Motore On or start switch, lever or position Engine chokeTable of Contents PrefaceTraining Safety InstructionsMaintenance and Storage PreparationSetting UP SpecificationsComponents Setting UP OperationOperation Mulch Plug Grass Deflector Adjusting the CUT HeightEngine Using the Self Propelled Transmission MaintenanceGrass Cutting and Catching Cleaning the Underside of the Mower MaintenanceGeneral Cleaning Adjusting the Drive CableReplacing the Drive Frame Cover Removing the Drive Frame CoverDrive Chain Lubrication Screw refer figure Discard the beltAdjusting the Drive Clutches Lubricating the Drive Pawls Above procedureMower cleaning using optional washport Replace the wheel plugs and the hubcapsEngine general Inspect and clean Visually inspect and cleanInspect and clean Have the engine serviced by an authorisedGeneral TroubleshootingProblem Possible CausesEngine cranks slowly Engine won’t crank Transmission doesn’t driveVorwort SymboleInhaltsverzeichnis Vorbereitung SicherheitshinweiseAnleitung BetriebTechnische Daten KomponentenVorbereitungen Betrieb Einstellen DER Schnitthöhe MulchauslassGrasabweiser MotorBedienung des Getriebes WartungMähen UND Auffangen DES Grases Den Motor starten und auf eine hohe Drehzahl einstellenAuswechseln DER Messer Allgemeine ReinigungReinigung der Mäherunterseite Einstellung des KupplungszugsAufsetzen der Antriebsabdeckung Einstellung des Kupplungszugs FortsetzungAbnehmen der Antriebsabdeckung Schmierung der AntriebsketteSiehe Abbildung Einstellung der AntriebsketteFreizulegen Oben 5 mm beträgt siehe AbbildungAb siehe Abbildung Austausch des Antriebsriemens FortsetzungEinstellung der Antriebskupplungen Durch die Abtriebswelle geht weist siehe AbbildungDie Radstopfen und die Nabenkappen wieder anbringen Schmierung der AntriebsklinkenFalls nicht, muss der Vorgang wiederholt werden Reinigung des Mähers mit Waschanschluss ZubehörMaßnahme KomponentenWeiterhin Allgemeines ProblembehandlungBehebung des Problems Mögliche UrsacheProblem Mögliche Ursache Préface SymbolesTable DES Matières Préparation Directives DE SécuritéInstructions UtilisationÉléments InstallationSpécifications Installation suite UtilisationDéflecteur D’HERBE Utilisation suiteObturateur DE Paillis Réglage DE LA Hauteur DE CoupeUtilisation de la transmission autotractée EntretienCoupe ET Ramassage DE L’HERBE Faites démarrer le moteur et réglez la vitesse sur rapideNettoyage du dessous de la tondeuse Entretien suiteNettoyage Général Pour Changer LES Lames DE CoupePour replacer le carter du châssis d’entraînement Réglage du câble d’entraînement suitePour enlever le carter du châssis d’entraînement Lubrification de la chaîne d’entraînementExposer la vis de réglage de la courroie voir figure Réglage de la chaîne d’entraînementRéglage de la courroie d’entraînement Dévissez la vis de réglage de deux 2 tours completsPour remplacer la courroie d’entraînement suite Réglage des embrayages d’entraînementLubrification des cliquets d’entraînement Lames de coupe Éléments du filtreHuile du moteur Batterie Selon modèleProblème Conseils EN CAS DE PanneGénéral Mesures correctivesProblème Causes possibles DémarrerSímbolos PrólogoContenido Preparativos Instrucciones DE SeguridadAdiestramiento FuncionamientoDatos Técnicos PartesInstalación Instalación Continuación FuncionamientoDeflector DE Grama Funcionamiento ContinuaciónAjuste DE LA Altura DEL Corte Cómo usar la transmisión de autopropulsado MantenimientoCorte E Intercepción DE LA Grama Arranque el motor y seleccione la velocidad rápidaCambio DE Cuchillas Maintenimiento ContinuaciónLimpieza General Opción DE AutopropulsadoCómo quitar la cubierta de la armazón Mantenimiento ContinuaciónAjuste del cable de tracción Continuación Cómo colocar la cubierta de la armazónTornillo de ajuste de la correa figura Ajuste de la cadena de tracciónAjuste de la correa de tracción Cómo cambiar la correa de tracciónMismo. Esto provocará desgaste a la larga Cómo cambiar la correa de tracción ContinuaciónAjuste de los embragues Chaveta de enganche figuraPonga de nuevo los tapacubos y bloqueos de las ruedas Opción DE Bateria Recargable PowerstartCómo lubricar los trinquetes de tracción Limpieza de la máquina usando el puerto de lavado opcionalTrinquetes Cuando los haya Aceite del motorCuchillas Batería Cuando la hayaPosible causa Problemas Y Posibles SolucionesProblema Medida correctivaMedidas correctivas Opción DE Batería Recargable PowerstartPosibles causas Inhoudsopgave SymbolenInleiding Reserveonderdelen voor de body van de maaierVoorbereidingen VeiligheidsinstructiesOpleiding BedieningSpecificaties ComponentenGebruiksklaar Maken Gebruikslaar Maken vervolg Werking StellenGrasafbuigplaat Werking Stellen vervolgMulch Plug Regeling VAN DE MaaihoogteHoe de zelfvoortdrijvende Transmissie te gebruiken OnderhoudGras Maaien EN Opvangen Start de motor en zet de snelheid van de motor op snelHet reinigen van de onderkant van de maaimachine Onderhoud vervolgReiniging in HET Algemeen HET Vervangen VAN DE SnijmessenHet verstellen van de Aandrijfkabel vervolg Het smeren van de aandrijfkettingDe versnellingsbak riemschijf en gooi de riem weg Het vervangen van de aandrijfriem vervolg Het afstellen van de koppelingenHet smeren van de aandrijfpallen Breng de wielpluggen en de wieldoppen weer aanControleer en reinig Reinig boven-en onderkantMotorolie Controleer het nivo Gashendel kabel Controleer en smeerProbleem HET Oplossen VAN ProblemenAlgemeen HerstelwerkzaamheidMogelijke oorzaken Simboli PrefazioneIndice Preparazione AvvertenzeIstruzione FunzionamentoSpecificazioni ComponentiPreparazione Preparazione continua FunzionamentoDeflettore DELL’ERBA Funzionamento continuaCommutatore DEL Pacciame Regolare L’ALTEZZA DI TaglioUtilizzare la trasmissione a propulsione autonoma ManutenzioneTaglio E Raccolta DELL’ERBA Accendere il motore ed impostare il motore ad alta velocitàPulire la parte inferiore della falciatrice Manutenzione continuaPulizia Generale Sostituire LE LameRimettere il coperchio della struttura di trasmissione Regolare il cavo di trasmissione continuaRimuovere il coperchio della struttura di trasmissione Lubrificazione della catena di trasmissioneRegolazione della cinghia di trasmissione Regolazione della catena di trasmissionePer rendere visibile la catena Svitare il regolatore per due 2 giri completiAttraverso l’albero motore figura Rimettere della cinghia di trasmissione continuaRegolare la frizione Libero dal perno del cilindro figuraLubrificare i denti di trasmissione Ogni Il motore non parte Ricerca E Riparazione DI UN GuastoGenerale Possibili CauseProblema Possibili Cause Spare Parts Views Base Spare PartsHandle BAR Spare Parts Self Propelled Spare Parts Ancillary Spare Parts Brake lever assembly- 20 & 22 s/prop Throttle control assembly/ChokeBrake lever assembly- 20 push Upper Handlebar- Anti VibrationPour votre information personnelle GB For your recordFür lhre Aufzeichnung SP Para su referencia

80, 51 specifications

Rover 51,80 is a full-size luxury SUV that has garnered attention for its blend of performance, comfort, and advanced technology. This model showcases Rover's ability to merge traditional craftsmanship with modern amenities, providing a driving experience that appeals to a wide range of consumers.

One of the standout features of the Rover 51,80 is its robust powertrain. It typically comes with a variety of engine options, ranging from efficient diesel variants to powerful petrol engines. The engines are mated to a sophisticated automatic transmission system, offering smooth gear transitions that enhance driving comfort. The AWD system ensures optimal traction and stability, making it suitable for various road conditions, whether urban landscapes or rugged terrains.

Inside the Rover 51,80, luxury takes center stage. High-quality materials like premium leather and polished wood accents create an upscale atmosphere, while seats are ergonomically designed for maximum comfort during long journeys. The spacious cabin provides ample legroom and cargo space, catering to families and adventure seekers alike.

Technology is a focal point of the Rover 51,80. It features an advanced infotainment system equipped with a large touchscreen interface, which allows seamless access to navigation, media, and vehicle settings. The sound system is often designed in collaboration with top audio brands, providing an immersive listening experience. Additionally, connectivity options such as Apple CarPlay and Android Auto ensure that drivers can integrate their devices effortlessly.

Safety is paramount for Rover, and the 51,80 comes with a suite of advanced safety features designed to protect both occupants and pedestrians. These may include adaptive cruise control, lane-keeping assistance, and a comprehensive airbag system. The vehicle's robust framework also contributes to its high safety ratings.

Another characteristic that sets Rover 51,80 apart is its off-road capability. With adjustable air suspension and various terrain response settings, this SUV is adept at handling challenging landscapes while maintaining ride comfort. Whether tackling rocky trails or navigating snowy streets, the 51,80 proves itself as a versatile vehicle.

In summary, Rover 51,80 encapsulates a harmonious blend of luxury, performance, and technology. Its powerful engine options, luxurious interior, advanced safety features, and off-road prowess make it a compelling choice for those seeking a premium SUV that delivers on multiple fronts.
Top Page Image Contents