Panasonic CQ-VD7001U warranty Front, Center, Sub W, VTR Level, AUX Level

Settings (continued)

English

43

(AUDIO continued)

SP SETUP (Speaker set up)

Setting the absence/presence and size of each speaker

FRONT (Front speaker setting)

LARGE : for large speakers, when bass playback is possible (at least 100 Hz or lower)

SMALL : for small speakers, or when bass playback is not possible

	default:	LARGE
CENTER	(Center speaker setting)

LARGE : for large speakers, when bass playback is possible (at least 100 Hz or lower)

SMALL : for small speakers, or when bass playback is not possible

NONE : when not using a center speaker

default: NONE

*A center speaker (option, EAB-CF2 recommended) is required.

SURROUND (Surround speaker setting)

LARGE	: for large speakers, when bass playback is
	possible (at least 100 Hz or lower)
	: for small speakers, or when bass playback is
SMALL
	not possible
NONE	: when not using a surround speaker
		default:
			LARGE
SUB - W		(Subwoofer speaker setting)
	: when using a subwoofer
YES
	: when not using a subwoofer
NO
		default:
				NO

*A subwoofer (option, CJ-HD302 recommended) is required. A power amplifier (option) is also required for connecting a subwoofer.

Note:

¡While the private mode is active, only FRONT can be

adjusted.

SP LEVEL (Speaker level)

Adjusting the output balance of each speaker

FRONT L		(Left front speaker output bal-
		ance)
] : down,	[ : up
CENTER		(Center speaker output balance)
] : down,	[ : up
		(Right front speaker output bal-
FRONT R
		ance)
] : down,	[ : up
		(Right surround speaker output
R¡SURROUND
		balance)
] : down,	[ : up
		(Left surround speaker output
L¡SURROUND
		balance)
] : down,	[ : up
		(Subwoofer speaker output bal-
SUB - W
		ance)
] : down,	[ : up

Setting range: –10 dB to +10 dB (1 dB steps) Default: ± 0 dB for all speakers

A test signal (a continuous tone) is output from each speaker for approximately 2 seconds.

Adjust the output balance so that the tone appears to have the same volume from each speaker.

Adjusting the output balance:

Adjust the volume of all of the other speakers to the volume level of the speaker from which the test signal appears to be the quietest.

¡If the speaker setting is NONE (none) or NO (no) for a speaker, the test signal is not output and that speaker cannot be selected.

¡Turn rotary volume controller or press [}] or [{] (VOL) to adjust the volume of the test signal.

Note:

¡While the private mode is active, only

FRONT L and

FRONT R can be

adjusted.

SP DELAY (Speaker delay)

Adjusting the timing with which the audio from each speak- er reaches the listener’s position

(Center speaker delay time set-

CENTER ting)

] : down, [ : up

Setting range: 0 ms to 5 ms (1 ms steps) 1 ms = 0.001 seconds default: 0 ms

(Surround speaker delay time

SURROUND setting)

] : down, [ : up

Setting range: 0 ms to 15 ms (1 ms steps)

1 ms = 0.001 seconds default: 0 ms

¡Make this adjustment while listening to sound.

¡If the speaker setting is NONE (none) for a speaker, that

speaker cannot be selected.

¡When “PRO LOGIC” is displayed, 15 ms are automatically added to the delay time setting for the surround speakers.

MODE LEVEL

Setting the VTR/AUX input level

Make this setting if it is not possible to adjust the volume through the connected device (on the output side).

VTR LEVEL		(Setting for VTR)
	: sets the level low/sound volume increases
LOW
	: sets the level high/sound volume decreases
HIGH
		default:
			HIGH
AUX LEVEL		(Setting for AUX)
	: sets the level low/sound volume increases
LOW
	: sets the level high/sound volume decreases
HIGH

Note:

¡If the input level from VTR/AUX is too high, the audio will not be output normally.

¡After setting the input level

The volume can be adjusted by pressing [}] or [{] (VOL) on the remote control or turning rotary volume controller on the unit.

LPF/HPF (Low Pass Filter/High Pass Filter) Cut off frequency

LPF CUT OFF

(Sub-woofer Low Pass Filter)

: down,

: up

]

[

Setting range:

-

(in 5

Hz step)

60 Hz

160

Hz

default:

100 Hz

HPF CUT OFF

(High Pass Filter)

: down,

: up

]

[

Setting range: OFF ,

-

(in 5

Hz step)

90 Hz

225

Hz

default:

OFF

Note:

¡This setting is not available if CS Auto (SRS setting) is set to ON (on).

¡HPF CUT OFF (High pass filter) is enabled only on the front speakers (R/L) and rear speakers (L/R).

English

44

default: HIGH

: Previous menu	: Quit	: Select/adjust
[MENU] : Previous menu	[MODE] : Quit	[]] [[] [}] [{] : Select/adjust	[ENTER] : Determine

: Previous menu	: Quit	: Select/adjust
[MENU] : Previous menu	[MODE] : Quit	[]] [[] [}] [{] : Select/adjust	[ENTER] : Determine

44

CQ-VD7001U CQ-VD7001U

45