Quick Reference Front Panel Menus | Agilent Technologies n3304a

1 - Quick Reference

Front Panel Menus - continued

Voltage

Tran

Trigger

List

	VOLT	Sets the input voltage
R	V:MODE	Sets the voltage mode (FIXED, LIST)
R	V:RANG	Sets the input voltage range
R	V:SLEW	Sets voltage slew rate
R	V:SLW:N	Sets voltage slew rate for negative transitions
R	V:SLW:P	Sets voltage slew rate for positive transitions
R	V:TLEV	Sets the transient input voltage
R	V:TRIG	Sets the triggered input voltage
	TRAN	Enables/disables the transient generator (OFF/ON)
R	T:DCYC	Sets the transient duty cycle in continuous mode
R	T:FREQ	Sets the transient frequency in continuous mode
R	T:MODE	Sets the transient mode (CONT, PULSE, TOGGLE)
R	T:TWID	Sets the transient pulse width in pulse mode
	INIT:IMMED	Initiates the trigger system
R	ABORT	Aborts the initiated trigger
	LST:STEP	Sets the method of incrementing steps (ONCE, AUTO)
R	LST:CNT	Specifies the number of times the list is cycled
R	DWEL:0 EOL	Specifies the time period of each step
R	CURR:0 EOL	Specifies the current setting for each step
R	C:RANG:0 EOL	Specifies the current range for each step
R	C:SLEW:0 EOL	Sets the current slew rate for each step
R	C:SLW:N:0 EOL	Sets the negative current slew rate for each step
R	C:SLW:P:0 EOL	Sets the positive current slew rate for each step
R	C:TLEV:0 EOL	Sets the transient input current for each step
R	FUNC:0 EOL	Sets the list regulation mode (CURR, RES, VOLT)
R	RES:0 EOL	Specifies the resistance setting for each step
R	R:RANG:0 EOL	Specifies the resistance range for each step
R	R:SLEW:0 EOL	Sets the resistance slew rate for each step
R	R:SLW:N:0 EOL	Sets the negative resistance slew rate for each step
R	R:SLW:P:0 EOL	Sets the positive resistance slew rate for each step
R	R:TLEV:0 EOL	Sets the transient input resistance for each step
R	TRAN:0 EOL	Enables/disables the transient level for each step
R	T:DCYC:0 EOL	Sets the transient duty cycle for each step
R	T:FREQ:0 EOL	Sets the transient frequency for each step
R	T:MODE:0 EOL	Sets the mode of the transient generator (CONT, PULSE)
R	T:TWID:0 EOL	Sets the transient pulse width for each step
R	VOLT:0 EOL	Specifies the voltage setting for each step
R	V:RANG:0 EOL	Specifies the voltage range for each step
R	V:SLEW:0 EOL	Sets the voltage slew rate for each step
R	V:SLW:N:0 EOL	Sets the negative voltage slew rate for each step
R	V:SLW:P:0 EOL	Sets the positive voltage slew rate for each step
R	V:TLEV:0 EOL	Sets the transient input voltage for each step

16

Image 15

Agilent Technologies n3304a, n3305a, n3301a, n3303a, n3306a, n3302a, n3300a manual Quick Reference Front Panel Menus, Voltage

Contents

USER’S Guide Certification Warranty Information General Safety Summary Safety Symbols Declaration of Conformity Declaration Printing History Acoustic Noise Information Table of Contents TURN-ON Checkout 101 Front Panel -At a Glance Quick Reference Instrument Configuration Rear Panel At a GlanceQuick Reference Use the Function keys and Entry keys to enter a new value Front Panel Number Entry Immediate Action Keys Front Panel Annunciators Front Panel Menus At a Glance Voltage Quick Reference Front Panel Menus Complete description of all programming commands Scpi Programming Commands At a Glance Quick Reference Scpi Commands Task Where to find information Document OrientationGetting Started Map Safety Considerations Options and AccessoriesDescription Features and Capabilities Front Panel ControlsRemote Programming Constant Current CC Mode Operating ModesImmediate Current Level Software Current Limit Constant Resistance CR ModeGeneral Information Triggered Current Level Transient Current Level Constant Voltage CV Mode Triggered Resistance LevelTransient Resistance Level Transient Voltage Level Triggered Voltage Level Toggled Transient Operation Transient OperationContinuous Transient Operation Pulsed Transient Operation Triggering a transient pulse Triggering a preset levelList Operation Triggered Operation Risetime Transition Limitation Slew Rate and Minimum Transition Time Transition Time Slew Rate Examples Short On/Off Protection FeaturesResetting Latched Protection Input Control Overcurrent OverpowerOvertemperature General Information Overvoltage Reading Remote Programming Errors Reverse VoltageStatus Reporting Monitor Outputs Saving and Recalling SettingsExternal Control Signals Remote Sensing Fault Input MeasurementsPort On/Off Minimum and Maximum Measurements Power MeasurementsDC Measurements RMS Measurements Items Supplied CleaningInspection Damage Packaging Material Installing the Modules ProcedureInstallation Channel Number Location 3A. N3300A Outline Diagram Bench Operation Rack MountingDo not block the fan exhaust at the rear of the unit Power Cord Manually-Tightened ConnectorsInput Connections 6a. Manual Connector 8mm Screw Terminal Connector option UJ1 Wire Considerations Stranded Copper Wire Ampere Capacity Wire Size AmpacityMaximum Wire Lengths to Limit Voltage Drops +S and -S Control ConnectorA1-A3 A11 and A10 Trigger and Digital Connections Sense Switch Computer Connections Gpib InterfaceRS-232 Interface Parallel Connections Application ConnectionsLocal Sense Connections Remote Sense Connections 11. Remote Sensing 13. Zero Volt Loading Low Voltage Operation Checkout Procedure IntroductionCheckout Programming Values Case of Trouble Error MessagesSelftest Errors Selftest Error Codes Front Panel, Overall View Front Panel Description Front Panel Operation System Keys Display Command Function Immediate Action Keys Function keys Scrolling Keys Metering KeysDisplay Measurement Inpshor Input Control Keys Transient Control Keys Trigger Control KeysList Control Keys Entry Keys Entry Keys Programming Constant Current, Voltage and Resistance Modes Using the Front Panel DisplaySet the constant current mode input Examples of Front Panel Programming Set the constant voltage mode input Set the constant resistance mode input Programming Transient Operation Set transient operation for Continuous mode Set transient operation for Toggled mode Set transient operation for Pulse mode Tmode Togg Programming Lists List Sequence Use the Meter menu for making front panel measurements Querying and Clearing Output Protection and ErrorsQuery and Clear Errors as follows Making Basic Front Panel Measurements Save an instrument state in location 0 as follows Setting the Gpib AddressStoring and Recalling Instrument States Set the Gpib address as follows Specifications Specifications Table A-2. Supplemental Characteristics Specifications a N3302A N3303A N3304A N3305A N3306A Specifications Equipment Required Performance Test and Calibration Procedures Performance Test and Calibration CC Mode TestsPerformance Tests Imon Zero Verification Voltage Programming and Measurement Accuracy Test CV Mode TestsCC Mode Regulation Test Performance Test and Calibration B CV Mode Regulation Test CR Mode Tests Resistance Range 1 Programming AccuracyResistance Range 2 Programming Accuracy Resistance Range 4 Programming Accuracy Resistance Range 3 Programming Accuracy Frequency and Duty Cycle Accuracy Transient Generator Mode Tests Output 705TRAN on Output 705TRIGIMM Performance Test and Calibration Pulse Width Accuracy Agilent N3302A Verification Test Record Agilent N3303A Verification Test Record Agilent N3304A Verification Test Record Agilent N3305A Verification Test Record Agilent N3306A Verification Test Record Calibration Figure B-3. Voltage Calibration Table B-2 Variables and Power Source Settings CalibrationParameters Calibrated IMON, Iprog and Current Calibration Program Performance Test and Calibration Wait Performance Test and Calibration Print TABXY9,15CALIBRATING High Voltage Range Voltage Calibration Program Performance Test and Calibration Resistance Calibration Program Calibrating Range Performance Test and Calibration B 100 101 Index 102 Index 103 Japan United States Latin AmericaCanada Australia/New Zealand Europe Asia Pacific Manual Updates