Projector WUX10 MarkII User Commands
Item | Code | TYPE | Error character strings | Error | Remedy | |
|
|
|
|
|
| |
| F001 | e | SYSTEM (UNKNOWN) | An internal error has occurred. | Resend the command. | |
|
|
|
|
|
| |
| F002 | e | SYSTEM (AF) | An error occurred at |
| |
| AUTOSETEXE=FOCUS. |
| ||||
|
|
|
|
| ||
11 |
|
|
|
| Eliminate the cause of the error, and | |
F004 | e | SYSTEM (AK) | An error occurred at | |||
| AUTOSETEXE=VKS. | resend the command. | ||||
|
|
|
| |||
|
|
|
|
|
| |
| F005 | e | SYSTEM (ASC) | An error occurred at |
| |
| AUTOSETEXE=SCRN. |
| ||||
|
|
|
|
| ||
|
|
|
|
|
| |
12 | E0XX | e | COMMUNICATION_ERROR | A communication protocol violation | Resend the command. | |
has occurred in the projector. | ||||||
|
|
|
|
|
| |
| 1008 | e |
| Cannot execute command under | Change the screen aspect ratio | |
| INVALID_SCREEN_ASPECT | current screen aspect ratio setting. | setting. | |||
|
|
| ||||
|
|
|
|
|
| |
|
|
|
| Cannot execute command with |
| |
14 | 200X | e | INVALID_SOURCE (****) | current input source. | Change the input source. | |
| ||||||
Current input source is indicated in | ||||||
|
|
|
|
| ||
|
|
|
| parentheses. |
| |
| 2010 | e | NO_SIGNAL | No input signal. | Supply the input signal. | |
|
|
|
|
|
| |
15 |
|
|
| Cannot execute command with |
| |
201X | e | INVALID_SIGNAL (****) | current input signal. | Change the input signal. | ||
| Current input signal is indicated in | |||||
|
|
|
|
| ||
|
|
|
| parentheses. |
| |
16 | 2020 | e | INVALID_IMAGE_MODE | Cannot execute command with | Change the image mode. | |
current image mode. | ||||||
|
|
|
|
| ||
17 | 0801 | e | INVALID_VALUE | Numerical parameters are invalid | Set the parameters in the correct | |
or outside the specified range. | range. | |||||
|
|
|
| |||
|
|
|
|
|
| |
| 1003 | e | IP_NOT_AVAILABLE | IP conversion is not possible. | Switch to the correct input signal. | |
| 1004 | e | POWER_MANAGEMENT_O | DPON=ON cannot be set when | Use a setting other than PMM=OFF. | |
| PMM=OFF. | |||||
|
|
| ||||
|
|
| FF |
|
| |
| 1005 | e | DIRECT_POWER_ON | PMM=OFF cannot be set when | Use the DPON=OFF setting. | |
| DPON=ON. | |||||
|
|
|
|
| ||
|
|
|
|
|
| |
|
|
|
| Invalid input signal resolution. |
| |
|
|
| INVALID_RESOLUTION | Additional information is indicated | Switch to an input signal with the | |
| 203X | e | in parentheses. | |||
| (***) | ■OVER_PANEL_RES: input | correct resolution. | |||
|
|
| ||||
|
|
|
|
| ||
|
|
|
| signal resolution exceeds panel |
| |
|
|
|
| resolution. |
| |
19 | - | i | INPUT_NOT_FOUND | Input was not switched since there | Notification of status only; no | |
is no input signal at | particular measures needed. | |||||
|
|
|
| AUTOSETEXE=INPUT. | ||
|
|
|
|
|
*Error codes are
*Items with lower numbers have a higher priority. (Even when multiple errors have occurred, the error with the highest rank is returned. However, errors of the same item number are ranked with the same priority.)
Revision History / Date
Changes
Revised by
Approved by
- 82 -
