Crane Merchandising Systems 480 - page 96

Refreshment Center Operators’ Guide Programming Procedures

December 2004 91 4800006

VIEW DIAGNOSTIC MESSAGES1. Press . the display shows any of the following diagnostic messages, depending upon any fault(s) present:

ERROR MESSAGES

None of the following erro rs are detected:

This appears if the SureVend™ anti-jackpot timer is active, showing

the time remaining on the timer. This timer is cleared u pon closure of

the main service door.

This shows the total number of times the S ureVend™ anti-jackpot

feature occurred plus the date and tim e of the last occurrence. Press

to reset this count.

Incomplete card reader communications. Check cables or replace

unit.

Incomplete card reader communications - check cables. The card

reader is not operational.

Card reader is indicating it has a proble m .

Card reader has an error and in dicates code XX. The code is d efined

by the card reader manufacturer. To correct, contact card reader

manufacturer. The unit is still operational.

Card reader is indicating it has failed . Rep lace unit.

Card reader has failed and indicate s co de XX. The code is defined

by the card reader manufacturer. To correct, contact card reader

manufacturer.

Card reader has failed because card is ja m m ed in the unit. Remove

the jammed card.

Card reader requires service. The unit is still o perational.

Price error detected and ch anged to maximum - check prices.

A PRODUCT CONFIG value was out of bounds and set to nominal -

check all PRODUCT CONFIGs.

The vending machine is telling t he bill validator not to accept any bill s.

Check the enabled channels of the bi ll validator.

Incomplete bill validator communications -- check harness.

A bill is jammed in the acceptance path. The un it will disable itself

until the error is corrected. Remove bill stuck in the acceptance p ath.

Cycle machine power OFF and the n ON .

One of the motors has failed. The unit wi ll disable itself until the error

is corrected. Check for bill stuck in the ac c ep tance path. If no bill is

present, replace the validator. Cycle machine power OFF and then

ON.

Contents

Main Refreshment Center Operators Guide Table of Contents TABLE OF CONTENTS Table of Contents Refreshment Center Op erators Page Page Page Page Refreshment Center Operators Guide Introduction Power Requirements Unpack the Machine Introduction Refreshment Center Operators Gu ide Controls and Indicators Refreshment Center Operators Guide Introduction Introduction Refreshment Center Operators Gu ide Turn the Merchandiser ON and OFF Refreshment Center Operators Guide Initial Set-Up Section 2: Initial Set-Up Moving the Merchandiser Through a Narrow Doorway Page Refreshment Center Operators Guide Initial Set-Up Open the Rear Outlet Diffuser Position the Merchandiser Configure Machine for Dual Zone Page Page Page Page Page Page Section 3: Tray Set-Up Place a Tray in the Loading Position Set up Trays to Vend Products Set Up A Tray To Vend Wide Products Remove a Snack or Candy Tray Page Remove a Bottle Tray Remove and Install Column Dividers Operate a Tray Outside of the Machine Replace a Motor with a Spiral Bearing Connect and Disconnect a Motor Harness Remove and Install Spirals All spirals are the same diameter There are two kinds of spirals NOTE Bottle trays use a 3.25 diameter spiral. Remove a Spiral Coupler Remove and Install a Spiral Motor Install a Gear ORIENTATION 1 ORIENTATION 2 Install a Spiral Coupler Move a Tray Up or Down Install a Tray in the Merchandiser Install and Remove a Product Spacer Section 4: Load the Merchandiser General Tray Loading: Special Considerations: Spiral Wall Retainer Usage Product Pusher Usage Configure the Merchandiser to vend Lunch Buckets Configure the Merchandiser for Vending "Top Shelf" Return the Trays to the Vending Position Install and Set Price Labels Page Page Refreshment Center Operators Guide SureVend Section 5: SureVend Health Control Refreshment Center Operators Guide Section 6: Health Control Refreshment Center Op erators Guide Health Control Section 7: Final Installation Level the Merchandiser Install the Base Plate Install the Lock Cylinder Install the Optional Cash Box Lock Set Up the Coin Mechanism Load the Coin Mechanism Operational Readiness Check Spiral Indexing Procedure (One Spiral, One Motor) Spiral Indexing Procedure (Two Spirals, One Or Two Motors) Test the Bill Validator Section 8: Programming Intro The Displays Refreshment Center Op erators Guide Programming Intro The Function Keys The keys on the control panel can have up to three functions: Other Keys One Last Thing: Control Panel Switches Explained Refreshment Center Op erators Guide Programming Intro December 2004 53 4800006 Programming Flow Charts Machine Configuration Functions Product Configuration Functions Tes ts Free Vend Supervisor Functions Diagnostics Pricing Payout Coins 4800006 54 December 2004 Data Recall Misc. Time of Day DEX/Printer Page # Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Index Refreshment Center Operators Guide Refreshment Center Operators Guide Index Terms and Conditions of Sale