Crane Merchandising Systems 480

Tray Set-Up Refreshment Center Operators’ Guide

4800006 20 December 2004

4. Unplug the tray wiring harness from the

PC board mounted on the tray guide rail

IMMEDIATELY ABOVE the tray you are

removing.

5. Lift up on the tray and slide it toward the

back. No more than an inch should be needed

6. The tab near the back of the tray should

align with the cut-out in the top of the guide rail

as shown.

7. Lift the tray clear of the guide rail and out of the

merchandiser.

CAUTION

When the cabinet door is not fully open, use extra

care in removing the bottom tray. Failure to do

so may result in damage to the tray or to

the delivery pan a ssembly.

PC BOARD

ATTACHED TO

TRAY GUIDE

TRAY GUIDE RAIL

TRAY

ROLLER

TRAY

GUIDE

RAIL

REAR OF TRAY

157P0026

CUT-OUT

TAB

(ON TRAY)

REAR OF

TRAY

TRAY GUID

RAIL

Contents

Main Refreshment Center Operators Guide Table of Contents TABLE OF CONTENTS Table of Contents Refreshment Center Op erators Page Page Page Page Refreshment Center Operators Guide Introduction Power Requirements Unpack the Machine Introduction Refreshment Center Operators Gu ide Controls and Indicators Refreshment Center Operators Guide Introduction Introduction Refreshment Center Operators Gu ide Turn the Merchandiser ON and OFF Refreshment Center Operators Guide Initial Set-Up Section 2: Initial Set-Up Moving the Merchandiser Through a Narrow Doorway Page Refreshment Center Operators Guide Initial Set-Up Open the Rear Outlet Diffuser Position the Merchandiser Configure Machine for Dual Zone Page Page Page Page Page Page Section 3: Tray Set-Up Place a Tray in the Loading Position Set up Trays to Vend Products Set Up A Tray To Vend Wide Products Remove a Snack or Candy Tray Page Remove a Bottle Tray Remove and Install Column Dividers Operate a Tray Outside of the Machine Replace a Motor with a Spiral Bearing Connect and Disconnect a Motor Harness Remove and Install Spirals All spirals are the same diameter There are two kinds of spirals NOTE Bottle trays use a 3.25 diameter spiral. Remove a Spiral Coupler Remove and Install a Spiral Motor Install a Gear ORIENTATION 1 ORIENTATION 2 Install a Spiral Coupler Move a Tray Up or Down Install a Tray in the Merchandiser Install and Remove a Product Spacer Section 4: Load the Merchandiser General Tray Loading: Special Considerations: Spiral Wall Retainer Usage Product Pusher Usage Configure the Merchandiser to vend Lunch Buckets Configure the Merchandiser for Vending "Top Shelf" Return the Trays to the Vending Position Install and Set Price Labels Page Page Refreshment Center Operators Guide SureVend Section 5: SureVend Health Control Refreshment Center Operators Guide Section 6: Health Control Refreshment Center Op erators Guide Health Control Section 7: Final Installation Level the Merchandiser Install the Base Plate Install the Lock Cylinder Install the Optional Cash Box Lock Set Up the Coin Mechanism Load the Coin Mechanism Operational Readiness Check Spiral Indexing Procedure (One Spiral, One Motor) Spiral Indexing Procedure (Two Spirals, One Or Two Motors) Test the Bill Validator Section 8: Programming Intro The Displays Refreshment Center Op erators Guide Programming Intro The Function Keys The keys on the control panel can have up to three functions: Other Keys One Last Thing: Control Panel Switches Explained Refreshment Center Op erators Guide Programming Intro December 2004 53 4800006 Programming Flow Charts Machine Configuration Functions Product Configuration Functions Tes ts Free Vend Supervisor Functions Diagnostics Pricing Payout Coins 4800006 54 December 2004 Data Recall Misc. Time of Day DEX/Printer Page # Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Index Refreshment Center Operators Guide Refreshment Center Operators Guide Index Terms and Conditions of Sale