Emerson Process Management OXYMITTER 4000 - page 84

Instruction Manual

IB-106-340C Rev. 4.1

July 2004

6-6 Startup and Operation with LOI Rosemount Analytical Inc. A Division of Emerson Process Management

Hazardous Area Oxymitter 4000

d. SYSTEM/Status

1. Alarm s – Diagnostic alarms. See

Section 8, TROUBLESHOOTING.

2. PID Parameter – Displays the line volt-

age, powering the Oxymitter, and infers

the temperature control algorithm being

used to control heater temperature.

3. Reset Device – Device can be reset

here as opposed to re-powering. Cali-

bration parameters will be lost.

e. SYSTEM/Software

This is data regarding the Oxymitter 4000

software version, and errors that may have

occurred.

f. SENSOR DATA

Displays information about the O2 cell and

thermocouple.

1. Temperatures

(a) O2 Temp – Indicates the thermo-

couple temperature at the sensing

cell; this should always be 736°C.

(b) O2 Temp Max. – Maximum tem-

perature the cell has seen. (Some

process temperatures can exceed

the 736°C setpoint temperature,

and this will indicate this condition.)

(c) Board Temp – The tem perature

inside the Oxymitter electronics

housing (85°C is the max.).

(d) Board Temp Max. – This is the

maximum temperature that the

electronics has experienced over

time.

6-7 LOI INSTALLATION

The LOI connects to the top of the electronic

assembly in the electronics housing. There are

four matching connectors on the back of the LOI

module, Figure 6-5, that allow the LOI to be ori-

ented as desired by the user.

37260055

CONNECTOR

RECEPTACLES

LOI MODULE

REAR VIEW

Figure 6-5. LOI Module Connectors

Contents

Main ESSENTIAL INSTRUCTIONS READ THIS PAGE BEFORE PROCEEDING! HIGHLIGHTS OF CHANGES HIGHLIGHTS OF CHANGES (Continued) TABLE OF CONTENTS Page LIST OF ILLUSTRATIONS LIST OF TABLES PREFACE DEFINITIONS NOTE TO USERS IMPORTANT SAFETY INSTRUCTIONS FOR THE WIRING AND INSTALLATION OF THIS APPARATUS BELANGRIJK VIGTIGT BELANGRIJK TRKE IMPORTANT Wichtig Sicherheitshinweise fr den Anschlu und die Installation dieser Gerte. Page VIKTIG Page Page VIKTIGT Page SECTION I. IDENTIFICATION SECTION II. PHYSICAL DATA SECTION III. HAZARDOUS INGREDIENTS SECTION IV. FIRE AND EXPLOSION DATA SECTION V. HEALTH HAZARD DATA THRESHOLD LIMIT VALUE EFFECTS OF OVER EXPOSURE EXPOSURE TO USED CERAMIC FIBER PRODUCT SPECIAL TOXIC EFFECTS SECTION VI. REACTIVITY DATA STABILITY/CONDITIONS TO AVOID HAZARDOUS POLYMERIZATION/CONDITIONS TO AVOID INCOMPATIBILITY/MATERIALS TO AVOID HAZARDOUS DECOMPOSITION PRODUCTS SECTION VII. SPILL OR LEAK PROCEDURES SECTION VIII. SPECIAL PROTECTION INFORMATION SECTION IX. SPECIAL PRECAUTIONS PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING CONCENTRATION Page GENERAL PRECAUTIONS FOR HANDLING AND STORING HIGH PRESSURE GAS CYLINDERS SECTION 1 DESCRIPTION AND SPECIFICATIONS Figure 1-1. Typical System Package HAZARDOUS AREA OXYMITTER 4000 IMPS 4000 REMOTE MOUNTED SPS 4000 Page Page Page STANDARD IMPS 4000* MULTIPROBE AUTOCALIBRATION OPTION REMOTE MOUNTED SPS 4000* SINGLE PROBE AUTOCALIBRATION OPTION (WITH REFERENCE AIR OPTION) Figure 1-6. Typical System Installation O xymitter 4000 with Integral Electronics STANDARD IMPS 4000* MULTIPROBE AUTOCALIBRATION OPTION Figure 1-7. Typical System Installation O xymitter 4000 with Remote Electronics REMOTE MOUNTED SPS 4000* SINGLE PROBE AUTOCALIBRATION OPTION (WITH REFERENCE AIR OPTION) Page Hazardous Area Oxymitter 4000 VIEW A VIEW B A A B B Page Page Table 1-1. Product Matrix Table 1-1. Product Matrix (Continued) Page SECTION 2 INSTALLATION 2-2 Installation Rosemount Analytical Inc. A Division of Emerson Process Management AMBIENT WEATHER CONDITIONS Figure 2-1. Hazardous Area Oxymitter 4000 Probe Installation INSULATE IF EXPOSEDTO PROCESS FLOW MUST BE IN THIS DIRECTIONWITH RESPECT TO DEFLECTOR 3534B48G01 Rosemount Analytical Inc. A Division of Emerson Process Management Installation 2-3 PIPE MOUNT CONFIGURATION REMOTE ELECTRONICS WITH LOI AND WINDOW COVER REMOTE ELECTRONICS WITH MEMBRANE KEYPAD AND BLIND COVER WALL MOUNT CONFIGURATION Figure 2-2. Hazardous Area Oxymitter 4000 Remote Electronics Installation Figure 2-3. Hazardous Area Oxymitter 4000 Probe with Abrasive Shield 2-4 Installation Rosemount Analytical Inc. A Division of Emerson Process Management Rosemount Analytical Inc. A Division of Emerson Process Management Installation 2-5 MOUNTING PLATE OUTLINE Figure 2-4. Hazardous Area Oxymitter 4000 Mounting Plate Dimensions 2-6 Installation Rosemount Analytical Inc. A Division of Emerson Process Management INSTALLATION FOR MASONRY WALL STACK CONSTRUCTION INSTALLATION FOR METAL WALL STACK OR DUCT CONSTRUCTION Figure 2-5. Hazardous Area Oxymitter 4000 Mounting Plate Installation PROBE MOUNTING ABRASIVE SHIELD MOUNTING Page Page Page 2-10 Installation Rosemount Analytical Inc. A Division of Emerson Process Management WITHOUT SPS 4000 WITH REMOTE SPS 4000 Figure 2-9. Electrical Installation Hazardous Area Oxymitter 4000 with Integral Electronics WITH REOMTE IMPS 4000 Page 2-12 Installation Rosemount Analytical Inc. A Division of Emerson Process Management WIRING DIAGRAM Rosemount Analytical Inc. A Division of Emerson Process Management Installation 2-13 WIRING DIAGRAM Page Page ! SECTION 3 CONFIGURATION OF HAZARDOUS AREA OXYMITTER 4000 WITH MEMBRANE KEYPAD Page Page Page Page Page SECTION 4 CONFIGURATION OF HAZARDOUS AREA OXYMITTER 4000 WITH LOI Page Page Page Page Page SECTION 5 START UP AND OPERATION OF HAZARDOUS AREA OXYMITTER 4000 WITH MEMBRANE KEYPAD Page Page Page SECTION 6 START UP AND OPERATION OF HAZARDOUS AREA OXYMITTER 4000 WITH LOI O2: 0.00% LK warm up 367dgC O2: 2.59% LK normal Page Figure 6-4. Local Operator Interface M enu Tree (Sheet 1 of 2) Page Page Page Page Page SECTION 7 HART/AMS Page Page Page Rosemount Analytical Inc. A Division of Emerson Process Management HART/AMS 7-5 Figure 7-3. HART/AMS Menu Tree (Sheet 1 o f 3) Figure 7-3. HART/AMS Menu Tree (Sheet 2 o f 3) 7-6 HART/AMS Rosemount Analytical Inc. A Division of Emerson Process Management Rosemount Analytical Inc. A Division of Emerson Process Management HART/AMS 7-7 Figure 7-3. HART/AMS Menu Tree (Sheet 3 o f 3) Page Page Page SECTION 8 TROUBLESHOOTING 150 EMF (mV) 100 50 Page Page Page Alarms O2 T/C Open KEYPAD LOI Alarms O2 T/C Shorted KEYPAD LOI Alarms O2 T/C Reversed LOI KEYPAD Alarms ADC Error LOI KEYPAD LOI KEYPAD Alarms O2 Heater Open LOI KEYPAD Alarms Very Hi O2 Temp LOI KEYPAD Alarms Board Temp Hi LOI KEYPAD Alarms O2 Temp Low Alarms O2 Temp Hi KEYPAD LOI Alarms O2 Cell Open KEYPAD LOI Alarms O2 Cell Bad KEYPAD LOI Alarms O2 Cell Bad KEYPAD LOI Alarms O2 Cell Bad LOI KEYPAD Alarms O2 Cell Bad LOI KEYPAD Alarms Calib Failed LOI KEYPAD Page Page Calibration Record For Rosemount Analytical In Situ O2 Probe SECTION 9 MAINTENANCE AND SERVICE Page Page ALARMS MANUAL CALIBRATION * * Page Page Page Figure 9-3. Hazardous Area Oxymitter 4000 with Integral Electronics Exploded View 9-8 Maintenance and Service Rosemount Analytical Inc. A Division of Emerson Process Management Rosemount Analytical Inc. A Division of Emerson Process Management Maintenance and Service 9-9 REMOTE ELECTRONICS PROBE HEAD PROBE INTERCONNECTING CABLE Figure 9-4. Hazardous Area Oxymitter 4000 with Remote Electronics Exploded View Page Page Page Page Page Page Page Page Page SECTION 10 RETURN OF MATERIAL Page SECTION 11 REPLACEMENT PARTS Page Page Page SECTION 12 OPTIONAL ACCESSORIES ASSET MANAGEMENT SOLUTIONS Page Page Page SECTION 13 INDEX A B C D Page WARRANTY Hazardous Area Oxymitter 4000 Part no. Serial no. Order no.