Analog Controls, Digital Controls | Euphonix 5B specification

System 5-B Digital Audio Mixing System Operation Manual	Channels and Strips

Analog Controls

If an ML530 Mic/Line Interface is patched to the input, the top four knobs show the analog mic/line controls:

•The top knob display shows whether the input is high or low impedance (HiZ = line; LowZ = mic). Press the lower switch to the left of the knob to toggle between values.

•The second knob display shows whether the 48 V phantom power is on/off. Press the lower switch to the left of the knob to toggle phantom power on/off.

•The third knob display shows whether the high-pass filter is on/off. Press the lower switch to the left of the knob to toggle the HPF on/off.

•The fourth knob controls the analog input gain. Spin the knob to adjust the gain between -12 and +72 dB.

NOTE: If an ML530 Mic/Line Interface is not patched to the input, the top four knobs are blank.

Digital Controls

The bottom four knobs control the digital parameters of the A and B inputs:

•The Atrm knob adjusts the digital trim ±15 dB.

•Aphs controls the phase of the A input. Press the lower switch to the left of the knob to toggle the phase. The switch lights to indicate phase reversal. Phase re- versal is indicated on the TFT screen above the Strip.

•Dly controls the delay for both inputs. Press the lower switch to the left of the knob to enable the delay. The switch lights to indicate the delay is active. Then rotate the knob to adjust the delay in the range 0–2160 samples.

•The Inpt knob selects between A, B, and A+B. The selection is indicated on the TFT screen above the Strip.

102

Image 102

Euphonix 5B operation manual Analog Controls, Digital Controls

Contents

Digital Audio Mixing System Page Important Safety Instructions Page Table of Contents Talkback Signal Patching Meters Meters Panel Master Section Meters Control Groups and Multi Format Masters 129 Page List of Figures Fader Controls Xiii Xiv List of Tables Page How to Use This Manual Manual Structure Introduction Analog and Digital I/O Overview of the System Components1 DF64 Digital Audio Frame Microphone Inputs GPI/O Midi I/F Channels and Strips Additional Hardware ComponentsControl Surface Channel Format System 5-B Startup Sequence Mixer Model Aux Bus ConfigurationMix Bus Terminology USB Support New Features in Version Assign Channels to Console EMix SetupConnect and Play a CD Patch the CD Player Quickstart to Common Task Route to the Mix Bus 2Device Outputs page in PatchNet Assign a Channel to the Console Configure PatchNetConnect and Monitor a Microphone Back to PatchNet 4Microphone assignment in Device Outputs Route to the Mix Bus Directory ProjectsBrowse Existing Project Open or Create a Project 1Projects Window Titles Rename, Copy, Paste, or Delete a Project Create a New Title 3New Title dialog Select Current Operations on Current TitleOpen an Existing Title Edit Notes Title Defaults Setting the Title Defaults Normalled Connections Meter Presets PatchNet DSP Console I/O 8Console I/O a and B inputs Window Device Inputs and Outputs CablingMic/Line Interface Patching Patching Examples Patch 12 mics into channels Select the Destinations 11Selecting destination channels Patch the multitrack returns into channels Main Bus Send/Return 13R-1 and mics patched Talkback Signal Patching Monitor PatchingSolo Bus and Utility Patching Busses 15Main Bus Window with law palette Symbol Format Law Palette Externals SystemMixer Model Folddown 19Folddown window Diagnostics 20Diagnostics Window Masters EventsSystem 5 Logo EMix Application CM401 Master Section Monitoring Studio Monitor Source Selection 085 Control Room Monitor Controls Sum or IntercancelMain Section and Aux Send Format Follow Control Room Monitors Dim and Cut 4CR Output controls and Control Room Output Panel 4 SLS/Cue Monitor Outputs Communications Talkback Monitors Listenback Aux Busses Oscillator/Slate OscillatorSlate 7CommsSlate/Osc Panel Quick Access Communications Panels 8Quick Access Communication Panels Solo Mode Solo Solo Clear Intercancel, Momentary, and SumSolo Level Solo Speaker Selection Solo-Safe Backstop PFL Meters Meters Panel Meter Configuration Sto Clr Name Cnfg Peak CM401 Master Section Master Section Meters CM401 Master Section CM402 Center Section CM402 Center Section Channel Select Panel 2Channel Select Panel Knobset Panels Knobset Control Panel Preset # Left Right Main Route Bus Routing PanelGrp Route Grp Section Group Busses Introduction to System 5-B BussesMain Busses Auxiliary Sends Bus Master Functions Bus Master Knobset Mon Lock 1 Aux, Grp, and Main MastersBus Lock All Key 2Main Bus Master left and Individual Bus right Displays Configuring Aux Busses Group and Aux BussesIndividual Main Busses Toggle Pre/Post Toggle StereoToggle On/Off Set Unity Copy Faders to Aux Copy Aux to AuxAux to Faders Main and Group Bus Setup Bus Master Inserts Channels and Strips Strips Swap Channel Meter and Status Display Map Channels and Control Groups to Strips Individual Assignment Strip Controls Multiple Assignments Channel Assign Panel 3Channel Assign Panel Input Names or Channel Number Shortcut Assignment for Multiple Channels Strip Utilities Fader Meters Strip Lock Strip Expand Fader Meters Spill SelectFader Unity Knob and Fader Text Displays Function Keys Channel Control FeaturesChannel Name Rotary Knobs Touch-Sensitive Fader and Controls Select/Punch Keys All Mode Wave KeyBackstop PFL Talk Copy and Paste Channel Processing Functions Inputs Analog Controls Digital Controls Stereo Controls 9Stereo Controls Signal Processing In/Out Dynamics 105 Compressor Expander/GateSidechain Equalizers and Filters 11EQ and Filters knobsets Parametric EQ Aux Sends FiltersAux Send Knobsets Aux Send Knobset 5 Pan Pan Knobsets 112 Pan Graph SmartPanTrack Panner Module Trim & Phase Input Select Channel Process Order and Patch Points Channel Patch Points Channel Processor Order Insert Point 16Changing processor order Channel Mixing Functions Group Bus RoutingRoute a Channel to a Group Bus Last Main Bus Routing Route a Channel to a Main Section Mix Minus 121 Talk Control Groups Multi Format Masters Control Groups 124 Modify Control Group Create Control GroupAssign Control Group to Strip Name Control Group Multi Format Masters Clear Control Group Spill Control Groups or Multi Format Masters Layouts and Snapshots Layouts Create a New Layout 131 Recall a Layout Modify a LayoutRename a Layout Snapshots Delete a LayoutCreate a New Snapshot Individual Channels Update Snapshot Recall a Snapshot Rename a Snapshot Delete a Snapshot GPI/O Event System GP132 Input Type Settings Activation Values Input Types Output Type Settings Activation Values Output Types Event Configuration Display Logical Operators Event List Input Output Deleting Events GPI Examples Move a Fader to Turn Off the Floor Monitors Move a Fader to Turn On the Floor Monitors Channel # Activation level dB Activation Type Below Move a Fader to Start a Cart Machine Move a Fader to Stop a Cart Machine Video Switcher Turns a Specific Camera and Channel On Input # Active State Machine GP132 One Video Switcher Turns a Specific Camera and Channel Off Input # Active State Off Machine GP132 One 3Audio Follow video configuration Audio Follow Video 150 151 152 Index 154 155 156