GPI Examples | Euphonix 5B specs

System 5-B Digital Audio Mixing System Operation Manual	GPI/O Event System

11.9GPI Examples

Refer to Figure 11-1and Figure 11-2for these examples. The options available in the Input and Output Properties areas are summarized in Table 11-1and Table 11-2.

If an event consists of just one input, AND and OR deliver the same result and may be used interchangeably.

11.9.1Move a Fader to Turn Off the Floor Monitors

This example demonstrates how to turn off the floor monitors by moving any one of several faders above a selected level.

1.In the Event Configuration window, under Event List, click on the <click to add event> field.

The Add Event dialog appears.

2.Select Or as the logical operator from the dropdown menu.

3.Under Input, click on the <click to add input> field. The Add Input Event dialog appears.

4.Select Fader from the dropdown menu and click OK.

5.Configure the Input Properties to the following settings:

Channel #	1
Activation level (dB)	-50
Activation Type	Above

6.Repeat steps 3–5 for any additional channel faders and set the Channel # in step 5 to the new channel number.

7.Under Output, click on the <click to add output> field. The Add Output Event dialog appears.

8.Select Control Room from the dropdown menu and click OK.

9.Configure the Output Properties to the following settings:

Action	Monitor A
Active State	Off

143

Image 143

Euphonix 5B operation manual GPI Examples, Move a Fader to Turn Off the Floor Monitors

Contents

Digital Audio Mixing System Page Important Safety Instructions Page Table of Contents Talkback Signal Patching Meters Meters Panel Master Section Meters Control Groups and Multi Format Masters 129 Page List of Figures Fader Controls Xiii Xiv List of Tables Page Manual Structure How to Use This Manual Introduction Microphone Inputs Overview of the System Components1 DF64 Digital Audio Frame Analog and Digital I/O GPI/O Midi I/F Channel Format Additional Hardware ComponentsControl Surface Channels and Strips System 5-B Startup Sequence USB Support Aux Bus ConfigurationMix Bus Terminology Mixer Model New Features in Version Patch the CD Player EMix SetupConnect and Play a CD Assign Channels to Console Quickstart to Common Task 2Device Outputs page in PatchNet Route to the Mix Bus Back to PatchNet Configure PatchNetConnect and Monitor a Microphone Assign a Channel to the Console 4Microphone assignment in Device Outputs Route to the Mix Bus Browse Existing Project DirectoryProjects 1Projects Window Open or Create a Project Rename, Copy, Paste, or Delete a Project Titles 3New Title dialog Create a New Title Edit Notes Operations on Current TitleOpen an Existing Title Select Current Setting the Title Defaults Title Defaults Normalled Connections Meter Presets DSP PatchNet 8Console I/O a and B inputs Window Console I/O Mic/Line Interface Patching Device Inputs and OutputsCabling Patch 12 mics into channels Patching Examples Select the Destinations 11Selecting destination channels Patch the multitrack returns into channels 13R-1 and mics patched Main Bus Send/Return Solo Bus and Utility Patching Talkback Signal PatchingMonitor Patching 15Main Bus Window with law palette Busses Law Palette Symbol Format Mixer Model ExternalsSystem 19Folddown window Folddown 20Diagnostics Window Diagnostics System 5 Logo MastersEvents EMix Application CM401 Master Section Studio Monitoring 085 Monitor Source Selection Follow Control Room Monitors Sum or IntercancelMain Section and Aux Send Format Control Room Monitor Controls 4CR Output controls and Control Room Output Panel Dim and Cut 4 SLS/Cue Monitor Outputs Communications Monitors Talkback Aux Busses Listenback Slate Oscillator/SlateOscillator 7CommsSlate/Osc Panel 8Quick Access Communication Panels Quick Access Communications Panels Solo Solo Mode Solo Speaker Selection Intercancel, Momentary, and SumSolo Level Solo Clear Backstop PFL Solo-Safe Meters Panel Meters Sto Clr Name Cnfg Peak Meter Configuration CM401 Master Section Master Section Meters CM401 Master Section CM402 Center Section CM402 Center Section 2Channel Select Panel Channel Select Panel Knobset Control Panel Knobset Panels Preset # Left Right Grp Section Bus Routing PanelGrp Route Main Route Auxiliary Sends Introduction to System 5-B BussesMain Busses Group Busses Bus Master Knobset Bus Master Functions All Key 1 Aux, Grp, and Main MastersBus Lock Mon Lock 2Main Bus Master left and Individual Bus right Displays Individual Main Busses Configuring Aux BussesGroup and Aux Busses Set Unity Toggle StereoToggle On/Off Toggle Pre/Post Aux to Faders Copy Faders to AuxCopy Aux to Aux Bus Master Inserts Main and Group Bus Setup Strips Channels and Strips Swap Channel Meter and Status Display Individual Assignment Strip Controls Map Channels and Control Groups to Strips 3Channel Assign Panel Multiple Assignments Channel Assign Panel Shortcut Assignment for Multiple Channels Input Names or Channel Number Fader Meters Strip Utilities Strip Expand Strip Lock Knob and Fader Text Displays Spill SelectFader Unity Fader Meters Rotary Knobs Channel Control FeaturesChannel Name Function Keys Select/Punch Keys Touch-Sensitive Fader and Controls Backstop PFL All ModeWave Key Copy and Paste Talk Inputs Channel Processing Functions Digital Controls Analog Controls 9Stereo Controls Stereo Controls Dynamics Signal Processing In/Out 105 Sidechain CompressorExpander/Gate 11EQ and Filters knobsets Equalizers and Filters Parametric EQ Aux Send Knobsets Aux SendsFilters Aux Send Knobset Pan Knobsets 5 Pan 112 Track Panner Module Pan GraphSmartPan Channel Process Order and Patch Points Trim & Phase Input Select Channel Processor Order Channel Patch Points 16Changing processor order Insert Point Route a Channel to a Group Bus Channel Mixing FunctionsGroup Bus Routing Last Route a Channel to a Main Section Main Bus Routing Mix Minus 121 Talk Control Groups Control Groups Multi Format Masters 124 Name Control Group Create Control GroupAssign Control Group to Strip Modify Control Group Clear Control Group Multi Format Masters Spill Control Groups or Multi Format Masters Layouts and Snapshots Create a New Layout Layouts 131 Rename a Layout Recall a LayoutModify a Layout Create a New Snapshot SnapshotsDelete a Layout Individual Channels Recall a Snapshot Update Snapshot Delete a Snapshot Rename a Snapshot GP132 GPI/O Event System Input Types Input Type Settings Activation Values Output Types Output Type Settings Activation Values Logical Operators Event Configuration Display Input Event List Deleting Events Output Move a Fader to Turn Off the Floor Monitors GPI Examples Channel # Activation level dB Activation Type Below Move a Fader to Turn On the Floor Monitors Move a Fader to Start a Cart Machine Move a Fader to Stop a Cart Machine Input # Active State Machine GP132 One Video Switcher Turns a Specific Camera and Channel On Input # Active State Off Machine GP132 One Video Switcher Turns a Specific Camera and Channel Off Audio Follow Video 3Audio Follow video configuration 150 151 152 Index 154 155 156