Device Inputs and Outputs, Cabling | Euphonix 5B instruction

System 5-B Digital Audio Mixing System Operation Manual	eMix Application

Figure 4-9shows the lower part of the Console I/O window. The Selected: area shows the sources and destinations for the A Input and B Input cells selected above. The numbered tabs (1–48 etc.) display additional pages of patchpoints. The four buttons on the right of Figure 4-9perform the following functions:

•Patch: Makes a connection between selected patchpoints

•Unpatch: Breaks the connection between selected patchpoints

•Clear: Deselects selected patchpoints

•View Log: Shows a log of failed patches

Figure 4-9Bottom of Console I/O window

4.2.2Device Inputs and Outputs

There are up to 12 MADI device input/output ports on the console, each carrying up to 56 channels (44.1/48 kHz) or 28 channels (96 kHz).

NOTE: To clarify the use of the terms Inputs and Outputs in PatchNet, Device per- tains to equipment other than the System 5-B console. Therefore, Device In- puts refers to inputs to an external device, not the console.

4.2.3Cabling

This category handles MADI cable connections for the ML530 Mic/Line Interfaces.

Mic/Line Interface Patching

For mic inputs and analog inputs not at +4 dB, the Euphonix ML530 provides 24 preamps each with gain, phantom power, high-pass filter, and hiZ/loZ switching. The analog outputs are connected to an AM713 Analog to MADI converter which then con- nects to one of the MADI inputs on the SH612 Studio Hub.

41

Image 41

Euphonix 5B operation manual Device Inputs and Outputs, Cabling, Mic/Line Interface Patching

Contents

Digital Audio Mixing System Page Important Safety Instructions Page Table of Contents Talkback Signal Patching Meters Meters Panel Master Section Meters Control Groups and Multi Format Masters 129 Page List of Figures Fader Controls Xiii Xiv List of Tables Page Manual Structure How to Use This Manual Introduction 1 DF64 Digital Audio Frame Overview of the System ComponentsAnalog and Digital I/O Microphone Inputs GPI/O Midi I/F Control Surface Additional Hardware ComponentsChannels and Strips Channel Format System 5-B Startup Sequence Mix Bus Terminology Aux Bus ConfigurationMixer Model USB Support New Features in Version Connect and Play a CD EMix SetupAssign Channels to Console Patch the CD Player Quickstart to Common Task 2Device Outputs page in PatchNet Route to the Mix Bus Connect and Monitor a Microphone Configure PatchNetAssign a Channel to the Console Back to PatchNet 4Microphone assignment in Device Outputs Route to the Mix Bus Browse Existing Project DirectoryProjects 1Projects Window Open or Create a Project Rename, Copy, Paste, or Delete a Project Titles 3New Title dialog Create a New Title Open an Existing Title Operations on Current TitleSelect Current Edit Notes Setting the Title Defaults Title Defaults Normalled Connections Meter Presets DSP PatchNet 8Console I/O a and B inputs Window Console I/O Mic/Line Interface Patching Device Inputs and OutputsCabling Patch 12 mics into channels Patching Examples Select the Destinations 11Selecting destination channels Patch the multitrack returns into channels 13R-1 and mics patched Main Bus Send/Return Solo Bus and Utility Patching Talkback Signal PatchingMonitor Patching 15Main Bus Window with law palette Busses Law Palette Symbol Format Mixer Model ExternalsSystem 19Folddown window Folddown 20Diagnostics Window Diagnostics System 5 Logo MastersEvents EMix Application CM401 Master Section Studio Monitoring 085 Monitor Source Selection Main Section and Aux Send Format Sum or IntercancelControl Room Monitor Controls Follow Control Room Monitors 4CR Output controls and Control Room Output Panel Dim and Cut 4 SLS/Cue Monitor Outputs Communications Monitors Talkback Aux Busses Listenback Slate Oscillator/SlateOscillator 7CommsSlate/Osc Panel 8Quick Access Communication Panels Quick Access Communications Panels Solo Solo Mode Solo Level Intercancel, Momentary, and SumSolo Clear Solo Speaker Selection Backstop PFL Solo-Safe Meters Panel Meters Sto Clr Name Cnfg Peak Meter Configuration CM401 Master Section Master Section Meters CM401 Master Section CM402 Center Section CM402 Center Section 2Channel Select Panel Channel Select Panel Knobset Control Panel Knobset Panels Preset # Left Right Grp Route Bus Routing PanelMain Route Grp Section Main Busses Introduction to System 5-B BussesGroup Busses Auxiliary Sends Bus Master Knobset Bus Master Functions Bus Lock 1 Aux, Grp, and Main MastersMon Lock All Key 2Main Bus Master left and Individual Bus right Displays Individual Main Busses Configuring Aux BussesGroup and Aux Busses Toggle On/Off Toggle StereoToggle Pre/Post Set Unity Aux to Faders Copy Faders to AuxCopy Aux to Aux Bus Master Inserts Main and Group Bus Setup Strips Channels and Strips Swap Channel Meter and Status Display Individual Assignment Strip Controls Map Channels and Control Groups to Strips 3Channel Assign Panel Multiple Assignments Channel Assign Panel Shortcut Assignment for Multiple Channels Input Names or Channel Number Fader Meters Strip Utilities Strip Expand Strip Lock Fader Unity Spill SelectFader Meters Knob and Fader Text Displays Channel Name Channel Control FeaturesFunction Keys Rotary Knobs Select/Punch Keys Touch-Sensitive Fader and Controls Backstop PFL All ModeWave Key Copy and Paste Talk Inputs Channel Processing Functions Digital Controls Analog Controls 9Stereo Controls Stereo Controls Dynamics Signal Processing In/Out 105 Sidechain CompressorExpander/Gate 11EQ and Filters knobsets Equalizers and Filters Parametric EQ Aux Send Knobsets Aux SendsFilters Aux Send Knobset Pan Knobsets 5 Pan 112 Track Panner Module Pan GraphSmartPan Channel Process Order and Patch Points Trim & Phase Input Select Channel Processor Order Channel Patch Points 16Changing processor order Insert Point Route a Channel to a Group Bus Channel Mixing FunctionsGroup Bus Routing Last Route a Channel to a Main Section Main Bus Routing Mix Minus 121 Talk Control Groups Control Groups Multi Format Masters 124 Assign Control Group to Strip Create Control GroupModify Control Group Name Control Group Clear Control Group Multi Format Masters Spill Control Groups or Multi Format Masters Layouts and Snapshots Create a New Layout Layouts 131 Rename a Layout Recall a LayoutModify a Layout Create a New Snapshot SnapshotsDelete a Layout Individual Channels Recall a Snapshot Update Snapshot Delete a Snapshot Rename a Snapshot GP132 GPI/O Event System Input Types Input Type Settings Activation Values Output Types Output Type Settings Activation Values Logical Operators Event Configuration Display Input Event List Deleting Events Output Move a Fader to Turn Off the Floor Monitors GPI Examples Channel # Activation level dB Activation Type Below Move a Fader to Turn On the Floor Monitors Move a Fader to Start a Cart Machine Move a Fader to Stop a Cart Machine Input # Active State Machine GP132 One Video Switcher Turns a Specific Camera and Channel On Input # Active State Off Machine GP132 One Video Switcher Turns a Specific Camera and Channel Off Audio Follow Video 3Audio Follow video configuration 150 151 152 Index 154 155 156