CM402 Center Section | Euphonix 5B manual

System 5-B Digital Audio Mixing System Operation Manual

Chapter 6: CM402 Center Section

The CM402 Center Section module (Figure 6-1)is located to the left of the CM401 Master Section (which contains the Center Strip). The purpose of the CM402 is to ex- pand access to Center Strip channel’s functions so they are more readily available. It includes the following functional sections, from top to bottom:

•Bus Routing Panel

Bus routing for the Center Strip’s channel. See Bus Routing Panel on page 80.

•Aux, Input, and Filters knobsets with select panel

The Select Panel determines which functions of the Center Strip’s channel are displayed on the knobsets.

•Dynamics and EQ knobsets

The Center Strip channel’s dynamics and EQ are always displayed on these knobsets.

•Channel Select Panel

Assigns a channel to the Center Strip.

•Eight assignable Strip faders

Although traditionally used for Control Groups, any channel can be assigned to them using the same techniques to assign a channel to a Strip on the CM408.

Any channel on the console can be displayed on the Center Strip by pressing its Wave key. The Channel Select Panel can also assign channels to the Center Strip.

Once a channel has been assigned to the Center Strip,

•reassigning the Swap or Main channels on the original Strip is not reflected in the Center Strip.

•reassigning the Swap or Main channels on the Center Strip is not reflected in the original Strip.

•the original Strip can still control all of its functions.

75

Image 75

Euphonix 5B operation manual CM402 Center Section

Contents

Digital Audio Mixing System Page Important Safety Instructions Page Table of Contents Talkback Signal Patching Meters Meters Panel Master Section Meters Control Groups and Multi Format Masters 129 Page List of Figures Fader Controls Xiii Xiv List of Tables Page Manual Structure How to Use This Manual Introduction Microphone Inputs Overview of the System Components1 DF64 Digital Audio Frame Analog and Digital I/O GPI/O Midi I/F Channel Format Additional Hardware ComponentsControl Surface Channels and Strips System 5-B Startup Sequence USB Support Aux Bus ConfigurationMix Bus Terminology Mixer Model New Features in Version Patch the CD Player EMix SetupConnect and Play a CD Assign Channels to Console Quickstart to Common Task 2Device Outputs page in PatchNet Route to the Mix Bus Back to PatchNet Configure PatchNetConnect and Monitor a Microphone Assign a Channel to the Console 4Microphone assignment in Device Outputs Route to the Mix Bus Directory ProjectsBrowse Existing Project 1Projects Window Open or Create a Project Rename, Copy, Paste, or Delete a Project Titles 3New Title dialog Create a New Title Edit Notes Operations on Current TitleOpen an Existing Title Select Current Setting the Title Defaults Title Defaults Normalled Connections Meter Presets DSP PatchNet 8Console I/O a and B inputs Window Console I/O Device Inputs and Outputs CablingMic/Line Interface Patching Patch 12 mics into channels Patching Examples Select the Destinations 11Selecting destination channels Patch the multitrack returns into channels 13R-1 and mics patched Main Bus Send/Return Talkback Signal Patching Monitor PatchingSolo Bus and Utility Patching 15Main Bus Window with law palette Busses Law Palette Symbol Format Externals SystemMixer Model 19Folddown window Folddown 20Diagnostics Window Diagnostics Masters EventsSystem 5 Logo EMix Application CM401 Master Section Studio Monitoring 085 Monitor Source Selection Follow Control Room Monitors Sum or IntercancelMain Section and Aux Send Format Control Room Monitor Controls 4CR Output controls and Control Room Output Panel Dim and Cut 4 SLS/Cue Monitor Outputs Communications Monitors Talkback Aux Busses Listenback Oscillator/Slate OscillatorSlate 7CommsSlate/Osc Panel 8Quick Access Communication Panels Quick Access Communications Panels Solo Solo Mode Solo Speaker Selection Intercancel, Momentary, and SumSolo Level Solo Clear Backstop PFL Solo-Safe Meters Panel Meters Sto Clr Name Cnfg Peak Meter Configuration CM401 Master Section Master Section Meters CM401 Master Section CM402 Center Section CM402 Center Section 2Channel Select Panel Channel Select Panel Knobset Control Panel Knobset Panels Preset # Left Right Grp Section Bus Routing PanelGrp Route Main Route Auxiliary Sends Introduction to System 5-B BussesMain Busses Group Busses Bus Master Knobset Bus Master Functions All Key 1 Aux, Grp, and Main MastersBus Lock Mon Lock 2Main Bus Master left and Individual Bus right Displays Configuring Aux Busses Group and Aux BussesIndividual Main Busses Set Unity Toggle StereoToggle On/Off Toggle Pre/Post Copy Faders to Aux Copy Aux to AuxAux to Faders Bus Master Inserts Main and Group Bus Setup Strips Channels and Strips Swap Channel Meter and Status Display Individual Assignment Strip Controls Map Channels and Control Groups to Strips 3Channel Assign Panel Multiple Assignments Channel Assign Panel Shortcut Assignment for Multiple Channels Input Names or Channel Number Fader Meters Strip Utilities Strip Expand Strip Lock Knob and Fader Text Displays Spill SelectFader Unity Fader Meters Rotary Knobs Channel Control FeaturesChannel Name Function Keys Select/Punch Keys Touch-Sensitive Fader and Controls All Mode Wave KeyBackstop PFL Copy and Paste Talk Inputs Channel Processing Functions Digital Controls Analog Controls 9Stereo Controls Stereo Controls Dynamics Signal Processing In/Out 105 Compressor Expander/GateSidechain 11EQ and Filters knobsets Equalizers and Filters Parametric EQ Aux Sends FiltersAux Send Knobsets Aux Send Knobset Pan Knobsets 5 Pan 112 Pan Graph SmartPanTrack Panner Module Channel Process Order and Patch Points Trim & Phase Input Select Channel Processor Order Channel Patch Points 16Changing processor order Insert Point Channel Mixing Functions Group Bus RoutingRoute a Channel to a Group Bus Last Route a Channel to a Main Section Main Bus Routing Mix Minus 121 Talk Control Groups Control Groups Multi Format Masters 124 Name Control Group Create Control GroupAssign Control Group to Strip Modify Control Group Clear Control Group Multi Format Masters Spill Control Groups or Multi Format Masters Layouts and Snapshots Create a New Layout Layouts 131 Recall a Layout Modify a LayoutRename a Layout Snapshots Delete a LayoutCreate a New Snapshot Individual Channels Recall a Snapshot Update Snapshot Delete a Snapshot Rename a Snapshot GP132 GPI/O Event System Input Types Input Type Settings Activation Values Output Types Output Type Settings Activation Values Logical Operators Event Configuration Display Input Event List Deleting Events Output Move a Fader to Turn Off the Floor Monitors GPI Examples Channel # Activation level dB Activation Type Below Move a Fader to Turn On the Floor Monitors Move a Fader to Start a Cart Machine Move a Fader to Stop a Cart Machine Input # Active State Machine GP132 One Video Switcher Turns a Specific Camera and Channel On Input # Active State Off Machine GP132 One Video Switcher Turns a Specific Camera and Channel Off Audio Follow Video 3Audio Follow video configuration 150 151 152 Index 154 155 156