Honeywell DCP552 Mark II user manual Ramp-E

DCP552 Parameter Work Sheet

No.	Item code	Item	Factory default	User			Settings and descriptions
			settings	settings
61	C 61	Programming system	0		0	: RAMP-X and RAMP-T (θ) combined
					1	: RAMP-X and RAMP-E (∆SP) combined
62	C 62	Program time unit	0		0	: Hours, min (SPU/hour for RAMP-T)
					1	: Min, sec (SPU/min for RAMP-T)
					2	:	0.1 sec (SPU/sec for RAMP-T)
63	C 63	Time display (display panel 1	0		0	: Remaining segment time
		and 2)			1	: total operation time (after READY → RUN start)
65	C 65	SP decimal point position (CH1)	1		0 to 4
66	C 66	SP limit lower limit	PV1 range		–19999 to +20000 SPU
			lower limit
67	C 67	SP limit upper limit	PV1 range		–19999 to +20000 SPU
			upper limit
68	C 68	SP decimal point position (CH2)	1 or 3		0 to 4 on a model without CP compensation.
					0 to 3 on a model with CP compensation.
69	C 69	SP limit lower limit (CH2)	PV2 range		-19999 to +20000 SPU (CH2) on a model without CP
			lower limit		compensation.
					0 to 2000 SPU(CH2) on a model with CP compensation.
70	C 70	SP limit upper limit (CH2)	PV2 range
			upper limit
71	C 71	External switch input RSW5	0		0		: NOP (does not function)
					1		: RAMP-E
					2		: FAST
72	C 72	External switch input RSW6	0		3		: G.SOAK is cleared using OR
					4		: G.SOAK is cleared using AND
					5		: MANUAL/AUTO
73	C 73	External switch input RSW7	0		6		: AT start/terminate
					7		: NOP (does not function)
					8		: Auto load
74	C 74	External switch input RSW8	0		9		: NOP (does not function)
					10		: NOP (does not function)
					11		: O2 sensor check
75	C 75	External switch input RSW9 to 14	0		0	: BCD4 bit + BCD2 bit
		(program selection)			1	: Binary 6 bits
76	C 76	Communication address	0		0 to 127
77	C 77	Transmission rate	0		0	: 9600bps
					1	: 4800bps
					2	: 2400bps
					3	: 1200bps
78	C 78	Transmission code	0		0	:	8 bits, even parity, 1 stop bit
					1	:	8 bits, no parity, 2 stop bits
79	C 79	Communication protocol	0		0	: CPL
					1	: ST221 (no PV trend)
					2	: ST221 (PV trend)
80	C 80	Communication method	0		0	: RS-485
					1	: RS-232C
81	C 81	ROM ID	—		< Description >
82	C 82	ROM ITEM	—		Can only be referenced for mechanical service use.
83	C 83	ROM revision	—
84	C 84	Data version	—
85	C 85	CPU board ID	—
86	C 86	I/O board ID	—
90	C 90	PID type	1		0	: Improved
					1	: Compatible with Mark I
91	C 91	PV1 burnout	0		0	: Provided
					1	: Not provided
92	C 92	PV2 burnout	0		0	: Provided
					1	: Not provided
93	C 93	Time proportional output system	0		0	: Does not go on a second time in time proportional cycle.
		(CH1)			1	: Goes on a second time in time proportional cycle.
94	C 94	Time proportional output	0		0	: Does not go on a second time in time proportional cycle
		system (CH2)			1	: Goes on a second time in time proportional cycle

17