Honeywell MRP-2001, MRP-2001E 29

Installation of Optional Modules

Installation

2.6.2.1 4XTMF Transmitter Module Installation

The 4XTMF provides a supervised output for a local energy municipal box transmitter in addition to alarm and trouble reverse polarity. A jumper option allows the reverse polarity circuit to open with a system trouble condition if no alarm condition exists. A disable switch allows disabling of the transmitter output during testing to prevent accidental calling of the monitoring service.

Local Energy Municipal Box Service (NFPA 72 Auxiliary Fire Alarm Systems): Supervisory Current: 5.0 mA

Trip Current: 350 mA (subtracted from notification appliance power)

Coil Voltage: 3.65 VDC

Maximum Coil Resistance: 14.6 ohms

Maximum allowable wire resistance between panel and trip coil: 3 ohms Municipal Box wiring can leave the building

Remote Station Service (NFPA 72 Remote Station Fire Alarm Systems) - Intended for connection to a polarity reversal circuit or a Remote Station receiving unit having compatible ratings:

Maximum load for each circuit: 10 mA

Reverse polarity output voltage: 24 VDC

Remote Alarm and Remote Trouble wiring can leave the building

Before installing the module, place the disconnect switch to the down (disconnect) position to prevent accidental activation of the municipal box. Note that a Disconnect LED will illuminate after the module is installed in the FACP. In addition, the System Trouble indicator will turn on to indicate the Disconnect condition.

Note: 4XTMF Module is not directly suitable for transmitting reverse polarity supervisory signal. For an application using reverse polarity of a supervisory signal, refer to the Appendix titled "FACP with Keltron" on page 123.

TBL Jumper

TBL

J1

Disconnect Switch

shown in J2 disconnect position

Polarities are shown for module activation

TB1

1+

}Remote Alarm (power-limited)*

2-

3+

}Remote Trouble (power-limited)*

4-

5

No connection

6+

}Municipal Box (nonpower-limited)*

7-

*Wiring from these terminals can exit the protected premises. Dummy load terminals 6 and 7 (4.7kΩ, ¼ watt resistor) if Municipal Box is not connected.

4xtmf.cdr

Disconnect LED

Connect to FACP Connectors J4 & J5

Figure 2.14 4XTMF Transmitter Module

MRP-2001 & MRP-2001E PN 53040:A 4/16/2007

29

Contents

Deluge • Preaction Control Installation, Operation and Programming Manual Page Page Page Page Page Page Page Page Page SECTION Product Description 1.1Product Features Page 1.2 Specifications 1.3 Controls and Indicators 1.4Components 1.5 Optional Modules and Accessories Installation 2.1 Backbox Mounting Page Page 2.2 Operating Power 2.3 Input Circuits Page 2.4Output Circuits 2.4.2 Special Application DC Power Output Connections 2.4.3 Relays - Programmable 2.5 Power-limitedWiring Requirements 2.6 Installation of Optional Modules Page 2.6.2 4XTMF Municipal Box Transmitter Option Module Page 2.7 ANN-BUSDevices Page Page 2.7.2 ANN-BUSDevice Addressing 2.7.3 ANN-80Remote LCD Annunciator 2.7.4 Specifications 2.7.5 Installation Page Page 2.7.6 ANN-S/PGSerial/Parallel Printer Interface Installation Page 2.7.7 ANN-I/OLED Driver Module Page 2.7.8 ANN-LEDAnnunciator Module Page Page 2.7.9 ANN-RLYRelay Module Page Programming 3.1 User Programming 3.2Initial Power-up 3.3 Programming Screens Description 3.4 Programming and Passwords 3.5 Master Programming Level 3.5.1 FACP CONFIG (Application Templates) FACP CONFIG 1=N/A 2=N/A 3=N/A 1=ENABLED YES 2=TYPE PULL STATION 3=OUTPUT CIRCUIT MAP INPUT ZONE 1 1=NOUN/ADJECTIVE 2=DESCRIPTION ZONE 1 TYPE 1=PULL STATION 2=N/A 3=MANUAL RELEASE Page 1=ALARM NAC 2=WATERFLOW NAC 3=RELEASE 4=SUPV BELL NAC 1=STANDARD ADJECTIVE 2=STANDARD NOUN 1=NORTH 1=3RD 2=SOUTH 2=4TH 3=EAST 1=BASEMENT 1=HVAC RM 2=BOILER RM 2=ISLAND 3=CLASSROOM Page 3.5.3 Output Circuits OUTPUT CIRCUITS 1=OUTPUT 1 2=OUTPUT 2 3=OUTPUT OUTPUT CIRCUITS 1=OUTPUT 1=ENABLED 2=TYPE EDIT OUTPUT # TYPE 1=RELEASE CIRCUIT 1 2=RELEASE CIRCUIT 2 3=ALARM NAC EDIT RELEASE CIR # 1=UNSUPV SHORTS 2=SUPV SHORTS RELEASE STAGES 1=RELEASE 1 ONLY 2=RELEASE 2 ONLY SILENCEABLE 1=SILENCEABLE 2=NON SILENCEABLE 3=SYNC MUTE AUTO SILENCE 1=NO 2=5 MINUTES 3=10 MINUTES AUTO SILENCE 1=15 MINUTES 2=20 MINUTES 3=25 MINUTES AUTO SILENCE 1=30 MINUTES CODING 1=STEADY 2=MARCH TIME 3=CALIFORNIA 1=TEMPORAL 2=FUTURE USE 3=FUTURE USE Page 3.5.4 Cross Input Zones CROSS INPUT ZONES 1=RELEASE 1 GROUPS 2=RELEASE 2 GROUPS REL 1 CROSS GROUPS REL CROSS GROUP 3.5.5 On-BoardRelays ON-BOARDRELAYS 1=RELAY ALARM 2=RELAY SYSTEM SETUP 1=FUTURE USE 2=TIMERS 3=BANNER SYSTEM SETUP 1=TIME-DATE2=TROUBLE REMIND NO 3=CHARGR DISABLE NO TIMERS 1=SOAK 2=SOAK SOAK # TIME 1=ALWAYS ON 2=ENTER MINUTES RANGE 10-30MINUTES WATERFLOW DELAY RANGE 00-90SECONDS AC LOSS DELAY RANGE 00-24HOURS SELECT BANNER 1=FACTORY BANNER 2=USER BANNER FACTORY BANNER PRESS ENTER IF OK USER BANNER-LINE1 TIME AND DATE 1=TIME 2=DATE ENTER TIME AS 12HRS 10:00 1=AM2=PM ENTER DATE MONTH DAY YEAR DAYLIGHT SAVINGS 2=START MONTH MAR 3=START WEEK 1=END MONTH 3.5.7 ANN-BUS 1=BUS ENABLED NO 2=BUS MODULES 3=AUTO CONFIGURE 1=ANN-S/PGOPTIONS 2=ANN-I/OOPTIONS 3=ANN-80OPTIONS 1=ANN-RLYOPTIONS 2=ANN-LEDOPTIONS ANN-BUSMODULES 1=ADDR 2=ADDR 3=ADDR ANN-BUSMODULE TYPE 1=NONE AUTO-CONGFIGURE IN PROGRESS PLEASE WAIT ANN-S/PGOPTIONS 1=PORT Page Page ANN-80OPTIONS 1=PIEZO ENABLE 2=LOCK ENABLE 3=ACK BTN ENABLE ANN-80OPTIONS 1=SIL BTN ENABLE 2=RST BTN ENABLE 3=DRL BTN ENABLE ANN-RLYOPTIONS IN ZONE ZONE 3.5.8 History HISTORY 1=VIEW EVENTS 2=ERASE HISTORY HISTORY 1=VIEW ALL 2=VIEW ALARMS 3=VIEW OTHER EVENTS ERASE HISTORY 3.5.9 Walktest WALKTEST 1=SILENT 2=AUDIBLE 3=VIEW EVENTS 3.5.10 Clear Program WARNING SYSTEM CHANGE PROCEED 3.5.11 Password Change 3.6 Maintenance Programming Level 3.6.1 Input Zones - Enable/Disable POINT PROGRAM 1=ZONE 1 2=ZONE 2 3=ZONE INPUT TYPE PULL STATION 3.6.3 Walktest 3.6.4 Time-Date 1=TIME01:00A 2=DATE 01012006 3=CLOCK FORMAT 12HRS 01:00 Operating Instructions 4.1 Panel Control Buttons 4.2 Indicators 4.3 Normal Operation 4.4 Trouble Operation 4.5 Alarm Operation 4.6Supervisory Operation 4.7 Disable/Enable Operation 4.8 Waterflow Circuits Operation 4.9 2nd-ShotWater Switch 4.10 Detector Functions 4.11 Time Functions: Real-TimeClock 4.12 Coded NAC Operation 4.13 Release Stages 4.14Special System Timers 4.15 Walktest 4.16 Read Status Normal 4.16.3 Output Circuits READ OUTPUTS 1=OUTPUT 1 2=OUTPUT 2 3=OUTPUT READ OUTPUTS 1=OUTPUT 4.16.4 Cross Input Zones CROSS INPUT ZONES 4.16.5 On-BoardRelays ON-BOARD RELAYS RELAY 4.16.6 System Settings 4.16.7 Timers SOAK 0 S 4.16.8 Daylight Savings ENABLED 4.16.9 History 4.16.10 PRINT PRINT 1=HISTORY 2=WALKTEST LOG 3=EXIT PRINTING 4.16.11 ANN-BUS BUS ENABLED NO 1=BUS MODULES 2=ANN-S/PGOPTIONS 1=ANN-80OPTION 2=ANN-RLYOPTIONS 5.1 Overview Power Supply Calculations 5.2Calculating the AC Branch Circuit 5.3Calculating the System Current Draw Page 5.4Calculating the Battery Size APPENDIX A A.1 Input-to-OutputCircuit Mapping and Cross-ZoneOperation A.1.1 Mapping Input Zones to Output Circuits for Direct Activation A.1.2 Mapping Input Zones to Release Circuits for Cross Zone Activation Page A.1.3 Complex Examples of Cross Zoning and I/O Mapping for Release Circuits APPENDIX B B.1 Template 7: Single Hazard - 3 Zone B.2 Template 8: Single Hazard - Cross-ZoneWith Manual Release B.3 Template 9: Dual Hazard - Combined Release B.4 Template 10: Dual Hazard - Split Release B.5 Template 11: Single Hazard - 3 Zones and Low Pressure B.6 Template 12: Single Hazard - 2 Zones Cross-ZonedWith All Active B.7 Template 13: Single Hazard - Dual Zone APPENDIX C Page Page C.1 NFPA 72 Auxiliary Fire Alarm System Page Page C.2 Central Station/Remote Station Transmitter: Connection to FACP Dry Contacts APPENDIX D FACP with Keltron APPENDIX E E.1 Testing E.2 Maintenance Page Page Page Page Page Page Page Page Page Limited Warranty