Motor TI, Cur Out, Low Val, High VAL, CO Range | Honeywell UDC3200

Function	Selections or
Prompt	Range of Setting
Lower Display	Upper Display
MOTOR TI	5 to 1800 seconds

CUR OUT

	DISABLE
	INPUT 1
	INPUT 2
	PV
	DEV
	OUTPUT
	SP
	LSP
	RSP
	IN ALG 1
LOW VAL	Low Scale Value
	within the range of
	the selected
	variable to
	represent the
	minimun output (0
	or 4 mA)

HIGH VAL	High Scale Value
	within the range of
	the selected
	variable to
	represent the
	maximum output
	(20 mA)

CO RANGE	4-20mA
	0-20mA

Parameter Definition

MOTOR TIME – Appears only when “POSITON” is selected as the Output algorithm. This is the time it takes the motor to travel from 0 to 100% (fully closed to fully open). This time can usually be found on the nameplate of the motor.

CURRENT OUTPUT – If Current Output #1 is not used to perform one of the above output algorithms, it may be used to perform an Auxiliary Output function.

DISABLE

INPUT 1

INPUT 2

PV (Process Variable)

DEVIATION

OUTPUT

SETPOINT

LOCAL SETPOINT

REMOTE

INPUT ALGORITHM 1

CURRENT OUTPUT LOW SCALING FACTOR—Used only when CUR OUT is any selection other than DISABLE. This is a value in engineering units used to represent all CUR OUT parameters except Output.

For Output, this is a value in percent and can be any value between –5 % and +105 %. However, keep in mind that relay output types can only be scaled 0 % to 100 %.

CURRENT OUTPUT HIGH SCALING FACTOR—Used only when CUR OUT is any selection other than DISABLE. This is a value in engineering units used to represent all CUR OUT parameters except Output.

For Output, this is a value in percent and can be any value between –5 % and +105 %. However, keep in mind that relay output types can only be scaled 0 % to 100 %.

CURRENT OUTPUT RANGE allows the user to easily select 4-20 mA output or 0-20 mA output operation without the need for recalibration of the instrument.

ATTENTION Changing the Current Output Range will result in the loss of Field Calibration values and will restore Factory Calibration values.

04/08

UDC3200 Universal Digital Controller Operator Manual

41

Image 47

Honeywell UDC3200 manual Motor TI, Cur Out, Low Val, High VAL, CO Range

Contents

UDC3200 Universal Digital Controller Operator Manual Telephone WARRANTY/REMEDYContacts World Wide Web Symbol Definition Symbol Definitions Contents TROUBLESHOOTING/SERVICE Page Function of Displays and Keys Operator InterfaceFunction of Displays and Keys Keys and Functions CE Conformity Europe UDC3200 Universal Digital Controller Operator Manual Page Model Number Interpretation Pre-installation Information Control Relays Control and Alarm Relay Contact InformationAlarm Relays Alarm Relay Contact Information Physical Considerations Overall DimensionsMounting Step Action Mounting Method Wiring Universal Output Functionality and Restrictions Wiring DiagramsPermissible Wiring Bundling Bundle No Wire Functions INU Details Wiring the ControllerCallout Line Neutral Voltage L2/N Earth Ground HotAC/DC RTD Input #1 Input 2 Connections Input #2 Time Duplex Time Simplex Relay Load L2/N PowerSupply Power Power Load Relay Load 10 Open Collector Output L2/N Relay Load Time Duplex with a Dual Relay Board UDC3200 Universal Digital Controller Operator Manual 04/08 15 RS-422/485 Communications Option Connections Digital Inputs 17 Auxiliary Output and Digital Inputs Option Connections 12 + 26 + Configuration Prompt Hierarchy Configuration Introduction Configuration ProcedureProcedure Configuration Procedure Tuning Set Up Group RSET2RPM CYC SEC CYC SX3 CYC2 SEC CYC2 SX3 Security Lockout Configuration is CompleteRSET2MIN 02 to SP SEL Auto MAN Disable Enable RUN HoldDisable Enable SP Ramp Set Up Group Strt SEG END SEG KeyresetEU/HR DN SP Prog SEG5RATE SEG6 SP SEG6TIME SEG2TIMESEG3RATE SEG4 SP SEG4TIME AT Error Accutune Set Up GroupFuzzy Disable Enable Accutune Tune ALG ON-OFF Algorithm Set Up Group ALG PD+MR Timer INP ALG1 Start KEY Alarm LOW Disp TI REM TimePeriod 000 to Multiplier Divider with Square Root -The following Summer with Ratio and BIAS-The following formulaInput High Select with Ratio and BIAS-This selection Input LOW Select with Ratio and BIAS- This selection Calc LO FCCMath K Calc HI ALG1 Bias ALG1 INBALG1 INC PCT CO OUT RNG Output Set Up GroupOUT ALG RLY Type Rlystate High VAL Motor TICUR OUT LOW VAL IN1 Type Input 1 Set Up Group Bias IN1 XmitterIN1 LOW Ratio 01 to Burnout NoneEMISSIV1 XMITTER2 Input 2 Set Up GroupIN2 Type Burnout Burnout Protection Sensor Break IN2 HighIN2 LOW Bias IN2 EMISSIV2 PID Sets 2PV SW Control Set Up GroupPV Source Input ALG1 PID Sets Input Input Algorithm PWR OUT PWR ModeRSP SRC None Input ALG1 Autobias SP Track PCT/M DN ActionOUT Rate PCT/M UP MAN OUT Failsafe ModeDeadband Failmode Minutes RPM No Auxiliary Output Options GroupAUX OUT Auxiliary Output Selection Was not previously started via DIG INP1No Digital Input Selections To RUN Digital Input 2 Selections Digital Input 2 Combinations DIG 1COMBDIG INP2 DIG2COMB Communications Group CSP Bias Shed SPUnits CSP Rato Alarms Set Up Group Beginning of Segment High AlarmLOW Alarm A1S1 EV A2S2TYPE A1S2 EVA2S1TYPE A2S1 EV Diagnost ALARM12 Display Set Up Group Page Operator Interface Entering a Security Code Individual key lockout Procedure to Enter a Security CodeKey error ALM 1 OUT 1 DI 1 Or MAN None, F or C Monitoring Your Controller 4.4.1 AnnunciatorsAnnunciators Lower Display Key Parameter Prompts Viewing the operating parameters Description Diagnostic MessagesDiagnostic Messages Functional Overview Block Diagram of the UDC3200 Controller Accutune Configuration checkTuning indicators Step Operation Press Result Procedure for Starting TuneTune for Simplex Outputs Operation Tune for Duplex Heat/Cool Configuration Check for Duplex Using Automatic Tune at start-up for Duplex Heat/Cool Using Manual Tune at start-up for Duplex Heat/Cool Using Blended Tune at start-up for Duplex Heat/Cool Step Operation Press Result Aborting Accutune Error Codes10 Procedure for Accessing Accutune Error Codes 11 Accutune Error Codes How it works ConfigurationFuzzy Overshoot Suppression INP1 RNG Background TestsBackground Tests EE Fail Curfail RV LimitSegerr CAL MTR Other symptoms Controller Failure Symptoms Sales and Service Page Http//hpsweb.honeywell.com