Step Operation Press Result | Honeywell UDC3200 specification

Step	Operation		Press		Result
4	Show Tuning				Until “TUNE OFF” is shown on
4	Show Tuning		Lower		Until “TUNE OFF” is shown on
	Prompt		Display		lower display.
			Display
5	Initiate Tuning				Select “DO SLOW” or “DO FAST”
					in lower display.
6	Tuning in operation				Upper display will show a “T” as
6	Tuning in operation		Lower		Upper display will show a “T” as
			Display		long as ACCUTUNE process is
					operating. When process
					completes, tuning parameters are
					calculated and lower display will
					show “NO TUNE” prompt.

Table 4-9 Procedure for Using MANUAL TUNE for Cool side of Duplex Control

Step	Operation		Press		Result
1	Configure LSP2				Until 2SP (Local Setpoint 2) shows
1	Configure LSP2		Lower		Until 2SP (Local Setpoint 2) shows
			Display		in the lower display.
			Display
2			or		Until LSP2 is a value within the
					Cool Zone (output below 50%).
3	Switch to				Until the “A” indicator is lighted (on
3	Switch to		Man		Until the “A” indicator is lighted (on
	“Automatic” Mode		Auto		controllers with Manual option).
			Auto
4	Show Tuning				Until “TUNE OFF” is shown on
4	Show Tuning		Lower		Until “TUNE OFF” is shown on
	Prompt		Display		lower display.
			Display
5	Initiate Tuning				Select “DO SLOW” or “DO FAST”
					in lower display.
6	Tuning in operation				Upper display will show a “T” as
6	Tuning in operation		Lower		Upper display will show a “T” as
			Display		long as ACCUTUNE process is
					operating. When process
					completes, tuning parameters are
					calculated and lower display will
					show “NO TUNE” prompt.

76

UDC3200 Universal Digital Controller Operator Manual

04/08

Image 82

Honeywell UDC3200 manual Step Operation Press Result

Contents

UDC3200 Universal Digital Controller Operator Manual World Wide Web WARRANTY/REMEDYContacts Telephone Symbol Definitions Symbol Definition Contents TROUBLESHOOTING/SERVICE Page Function of Displays and Keys Operator InterfaceFunction of Displays and Keys CE Conformity Europe Keys and Functions UDC3200 Universal Digital Controller Operator Manual Page Pre-installation Information Model Number Interpretation Alarm Relay Contact Information Control and Alarm Relay Contact InformationAlarm Relays Control Relays Mounting Overall DimensionsPhysical Considerations Mounting Method Step Action Wiring Bundle No Wire Functions Wiring DiagramsPermissible Wiring Bundling Universal Output Functionality and Restrictions INU Callout Wiring the ControllerDetails AC/DC Earth Ground HotLine Neutral Voltage L2/N Input #1 RTD Input #2 Input 2 Connections Time Simplex Time Duplex Power Load Relay Load L2/N PowerSupply Power Relay Load 10 Open Collector Output Time Duplex with a Dual Relay Board L2/N Relay Load UDC3200 Universal Digital Controller Operator Manual 04/08 15 RS-422/485 Communications Option Connections 17 Auxiliary Output and Digital Inputs Option Connections Digital Inputs 26 + 12 + Configuration Configuration Prompt Hierarchy Configuration Procedure Configuration ProcedureProcedure Introduction Tuning Set Up Group 02 to Configuration is CompleteRSET2MIN RSET2RPM CYC SEC CYC SX3 CYC2 SEC CYC2 SX3 Security Lockout Disable Enable Auto MAN Disable Enable RUN HoldSP SEL SP Ramp Set Up Group SP Prog KeyresetEU/HR DN Strt SEG END SEG SEG4 SP SEG4TIME SEG2TIMESEG3RATE SEG5RATE SEG6 SP SEG6TIME Fuzzy Disable Enable Accutune Tune Accutune Set Up GroupAT Error Algorithm Set Up Group ALG ON-OFF Timer ALG PD+MR 000 to Start KEY Alarm LOW Disp TI REM TimePeriod INP ALG1 Input LOW Select with Ratio and BIAS- This selection Summer with Ratio and BIAS-The following formulaInput High Select with Ratio and BIAS-This selection Multiplier Divider with Square Root -The following Calc HI FCCMath K Calc LO PCT CO ALG1 INBALG1 INC ALG1 Bias OUT ALG Output Set Up GroupOUT RNG Rlystate RLY Type LOW VAL Motor TICUR OUT High VAL Input 1 Set Up Group IN1 Type Ratio XmitterIN1 LOW Bias IN1 EMISSIV1 Burnout None01 to IN2 Type Input 2 Set Up GroupXMITTER2 Bias IN2 IN2 HighIN2 LOW Burnout Burnout Protection Sensor Break EMISSIV2 Input Input Algorithm Control Set Up GroupPV Source Input ALG1 PID Sets PID Sets 2PV SW SP Track PWR ModeRSP SRC None Input ALG1 Autobias PWR OUT PCT/M UP ActionOUT Rate PCT/M DN Failmode Failsafe ModeDeadband MAN OUT RPM Minutes Auxiliary Output Selection Options GroupAUX OUT No Auxiliary Output No Digital Input Selections DIG INP1Was not previously started via To RUN DIG2COMB DIG 1COMBDIG INP2 Digital Input 2 Selections Digital Input 2 Combinations Communications Group CSP Rato Shed SPUnits CSP Bias Alarms Set Up Group A1S1 EV High AlarmLOW Alarm Beginning of Segment A2S1 EV A1S2 EVA2S1TYPE A2S2TYPE ALARM12 Diagnost Display Set Up Group Page Entering a Security Code Operator Interface Key error Procedure to Enter a Security CodeIndividual key lockout Annunciators Monitoring Your Controller 4.4.1 AnnunciatorsALM 1 OUT 1 DI 1 Or MAN None, F or C Viewing the operating parameters Lower Display Key Parameter Prompts Diagnostic Messages Diagnostic MessagesDescription Functional Overview Block Diagram of the UDC3200 Controller Tuning indicators Configuration checkAccutune Operation Procedure for Starting TuneTune for Simplex Outputs Step Operation Press Result Configuration Check for Duplex Tune for Duplex Heat/Cool Using Automatic Tune at start-up for Duplex Heat/Cool Using Blended Tune at start-up for Duplex Heat/Cool Using Manual Tune at start-up for Duplex Heat/Cool Step Operation Press Result 11 Accutune Error Codes Error Codes10 Procedure for Accessing Accutune Error Codes Aborting Accutune Fuzzy Overshoot Suppression ConfigurationHow it works EE Fail Background TestsBackground Tests INP1 RNG CAL MTR RV LimitSegerr Curfail Controller Failure Symptoms Other symptoms Sales and Service Page Http//hpsweb.honeywell.com