Rpm, Minutes | Honeywell UDC3200 specs

Function	Selections or
Prompt	Range of Setting
Lower Display	Upper Display
MINUTESorRP
M
	RPM
	MINUTES

Parameter Definition

RESET UNITS—Selects units of minutes per repeat or repeats per minute for the I term of the PID algorithm.

20 Repeats per Minute = 0.05 Minutes per Repeat.

REPEATS PER MINUTE—The number of times per minute that the proportional action is repeated by reset.

MINUTES PER REPEAT—The time between each repeat of the proportional action by reset.

NOTE 1: Does not apply to Three Position Step Control.

NOTE 2: If controller is in Manual mode when a failure occurs, then the output will maintain its value. NOTE 3:These selections appear when:

A)Control Algorithm is selected for 3PSTEP.

B)Control Algorithm is selected for PD+MR and Output Algorithm is selected for Position Proportional.

NOTE 4: The local setpoint will automatically adjust itself to be within the setpoint limit range. For example, if SP = 1500 and the SP HiLIM is changed to 1200, the new local setpoint will be 1200.

NOTE 5: Reset limits and Dropoff are not displayed when Three Position Step Control is configured.

52

UDC3200 Universal Digital Controller Operator Manual

04/08

Image 58

Honeywell UDC3200 manual Rpm, Minutes

Contents

UDC3200 Universal Digital Controller Operator Manual World Wide Web WARRANTY/REMEDYContacts Telephone Symbol Definitions Symbol Definition Contents TROUBLESHOOTING/SERVICE Page Function of Displays and Keys Operator InterfaceFunction of Displays and Keys CE Conformity Europe Keys and Functions UDC3200 Universal Digital Controller Operator Manual Page Pre-installation Information Model Number Interpretation Alarm Relay Contact Information Control and Alarm Relay Contact InformationAlarm Relays Control Relays Mounting Overall DimensionsPhysical Considerations Mounting Method Step Action Wiring Bundle No Wire Functions Wiring DiagramsPermissible Wiring Bundling Universal Output Functionality and Restrictions INU Callout Wiring the ControllerDetails AC/DC Earth Ground HotLine Neutral Voltage L2/N Input #1 RTD Input #2 Input 2 Connections Time Simplex Time Duplex Power Load Relay Load L2/N PowerSupply Power Relay Load 10 Open Collector Output Time Duplex with a Dual Relay Board L2/N Relay Load UDC3200 Universal Digital Controller Operator Manual 04/08 15 RS-422/485 Communications Option Connections 17 Auxiliary Output and Digital Inputs Option Connections Digital Inputs 26 + 12 + Configuration Configuration Prompt Hierarchy Configuration Procedure Configuration ProcedureProcedure Introduction Tuning Set Up Group 02 to Configuration is CompleteRSET2MIN RSET2RPM CYC SEC CYC SX3 CYC2 SEC CYC2 SX3 Security Lockout Disable Enable Auto MAN Disable Enable RUN HoldSP SEL SP Ramp Set Up Group SP Prog KeyresetEU/HR DN Strt SEG END SEG SEG4 SP SEG4TIME SEG2TIMESEG3RATE SEG5RATE SEG6 SP SEG6TIME Fuzzy Disable Enable Accutune Tune Accutune Set Up GroupAT Error Algorithm Set Up Group ALG ON-OFF Timer ALG PD+MR 000 to Start KEY Alarm LOW Disp TI REM TimePeriod INP ALG1 Input LOW Select with Ratio and BIAS- This selection Summer with Ratio and BIAS-The following formulaInput High Select with Ratio and BIAS-This selection Multiplier Divider with Square Root -The following Calc HI FCCMath K Calc LO PCT CO ALG1 INBALG1 INC ALG1 Bias OUT ALG Output Set Up GroupOUT RNG Rlystate RLY Type LOW VAL Motor TICUR OUT High VAL Input 1 Set Up Group IN1 Type Ratio XmitterIN1 LOW Bias IN1 EMISSIV1 Burnout None01 to IN2 Type Input 2 Set Up GroupXMITTER2 Bias IN2 IN2 HighIN2 LOW Burnout Burnout Protection Sensor Break EMISSIV2 Input Input Algorithm Control Set Up GroupPV Source Input ALG1 PID Sets PID Sets 2PV SW SP Track PWR ModeRSP SRC None Input ALG1 Autobias PWR OUT PCT/M UP ActionOUT Rate PCT/M DN Failmode Failsafe ModeDeadband MAN OUT RPM Minutes Auxiliary Output Selection Options GroupAUX OUT No Auxiliary Output No Digital Input Selections DIG INP1Was not previously started via To RUN DIG2COMB DIG 1COMBDIG INP2 Digital Input 2 Selections Digital Input 2 Combinations Communications Group CSP Rato Shed SPUnits CSP Bias Alarms Set Up Group A1S1 EV High AlarmLOW Alarm Beginning of Segment A2S1 EV A1S2 EVA2S1TYPE A2S2TYPE ALARM12 Diagnost Display Set Up Group Page Entering a Security Code Operator Interface Key error Procedure to Enter a Security CodeIndividual key lockout Annunciators Monitoring Your Controller 4.4.1 AnnunciatorsALM 1 OUT 1 DI 1 Or MAN None, F or C Viewing the operating parameters Lower Display Key Parameter Prompts Diagnostic Messages Diagnostic MessagesDescription Functional Overview Block Diagram of the UDC3200 Controller Tuning indicators Configuration checkAccutune Operation Procedure for Starting TuneTune for Simplex Outputs Step Operation Press Result Configuration Check for Duplex Tune for Duplex Heat/Cool Using Automatic Tune at start-up for Duplex Heat/Cool Using Blended Tune at start-up for Duplex Heat/Cool Using Manual Tune at start-up for Duplex Heat/Cool Step Operation Press Result 11 Accutune Error Codes Error Codes10 Procedure for Accessing Accutune Error Codes Aborting Accutune Fuzzy Overshoot Suppression ConfigurationHow it works EE Fail Background TestsBackground Tests INP1 RNG CAL MTR RV LimitSegerr Curfail Controller Failure Symptoms Other symptoms Sales and Service Page Http//hpsweb.honeywell.com