Individual key lockout, Key error | Honeywell UDC3200 specification

Table 4-1 Procedure to Enter a Security Code

Step

Operation

Press

Result

1	Enter Set Up	Setup
	Mode	Setup
	Mode
2	Select any Set	Function
	Up Group	Function
	Up Group
3	Security Code	or
	Entry

Upper Display = SET UP

Lower Display = TUNING

Upper Display = 0

Lower Display = SECUR

To enter a four digit number in the upper display (0001 to 9999)

This will be your security code.

4.3 Individual key lockout

There are three keys that can be disabled to prevent unauthorized changes to the parameters associated with these keys. First set the “Lock” prompt to NONE.

These keys are:

Run

Hold

Key	- you can disable the Run/Hold key for Set Point
	Programming at configuration Set Up group prompt
	“Tuning,” function prompt “RN HLD.”

Man

Auto

Key	- you can disable the Auto/Manual key at configuration
	Set Up, group prompt “Tuning”, function prompt
	“AUTOMA”

SP

Select

Key	- you can disable the Set Point Select function key at
	configuration Set Up group prompt “Tuning,” function
	prompt “SP SEL.”

See Subsection 3.3 - Tuning Parameters Set Up Group prompts to enable or disable these keys.

Key error

When a key is pressed and the prompt “Key Error” appears in the lower display, it will be for one of the following reasons:

•Parameter not available or locked out

•Not in setup mode, press SET UP key first

•Individual key locked out.

66

UDC3200 Universal Digital Controller Operator Manual

04/08

Image 72

Honeywell UDC3200 manual Individual key lockout, Procedure to Enter a Security Code, Key error

Contents

UDC3200 Universal Digital Controller Operator Manual WARRANTY/REMEDY ContactsWorld Wide Web Telephone Symbol Definitions Symbol Definition Contents TROUBLESHOOTING/SERVICE Page Operator Interface Function of Displays and KeysFunction of Displays and Keys CE Conformity Europe Keys and Functions UDC3200 Universal Digital Controller Operator Manual Page Pre-installation Information Model Number Interpretation Control and Alarm Relay Contact Information Alarm RelaysAlarm Relay Contact Information Control Relays Overall Dimensions MountingPhysical Considerations Mounting Method Step Action Wiring Wiring Diagrams Permissible Wiring BundlingBundle No Wire Functions Universal Output Functionality and Restrictions INU Wiring the Controller CalloutDetails Earth Ground Hot AC/DCLine Neutral Voltage L2/N Input #1 RTD Input #2 Input 2 Connections Time Simplex Time Duplex L2/N Power Supply PowerPower Load Relay Load Relay Load 10 Open Collector Output Time Duplex with a Dual Relay Board L2/N Relay Load UDC3200 Universal Digital Controller Operator Manual 04/08 15 RS-422/485 Communications Option Connections 17 Auxiliary Output and Digital Inputs Option Connections Digital Inputs 26 + 12 + Configuration Configuration Prompt Hierarchy Configuration Procedure ProcedureConfiguration Procedure Introduction Tuning Set Up Group Configuration is Complete RSET2MIN02 to RSET2RPM CYC SEC CYC SX3 CYC2 SEC CYC2 SX3 Security Lockout Auto MAN Disable Enable RUN Hold Disable EnableSP SEL SP Ramp Set Up Group Keyreset EU/HR DNSP Prog Strt SEG END SEG SEG2TIME SEG3RATESEG4 SP SEG4TIME SEG5RATE SEG6 SP SEG6TIME Accutune Set Up Group Fuzzy Disable Enable Accutune TuneAT Error Algorithm Set Up Group ALG ON-OFF Timer ALG PD+MR Start KEY Alarm LOW Disp TI REM Time Period000 to INP ALG1 Summer with Ratio and BIAS-The following formula Input High Select with Ratio and BIAS-This selectionInput LOW Select with Ratio and BIAS- This selection Multiplier Divider with Square Root -The following FCC Math KCalc HI Calc LO ALG1 INB ALG1 INCPCT CO ALG1 Bias Output Set Up Group OUT ALGOUT RNG Rlystate RLY Type Motor TI CUR OUTLOW VAL High VAL Input 1 Set Up Group IN1 Type Xmitter IN1 LOWRatio Bias IN1 Burnout None EMISSIV101 to Input 2 Set Up Group IN2 TypeXMITTER2 IN2 High IN2 LOWBias IN2 Burnout Burnout Protection Sensor Break EMISSIV2 Control Set Up Group PV Source Input ALG1 PID SetsInput Input Algorithm PID Sets 2PV SW PWR Mode RSP SRC None Input ALG1 AutobiasSP Track PWR OUT Action OUT RatePCT/M UP PCT/M DN Failsafe Mode DeadbandFailmode MAN OUT RPM Minutes Options Group AUX OUTAuxiliary Output Selection No Auxiliary Output DIG INP1 No Digital Input SelectionsWas not previously started via To RUN DIG 1COMB DIG INP2DIG2COMB Digital Input 2 Selections Digital Input 2 Combinations Communications Group Shed SP UnitsCSP Rato CSP Bias Alarms Set Up Group High Alarm LOW AlarmA1S1 EV Beginning of Segment A1S2 EV A2S1TYPEA2S1 EV A2S2TYPE ALARM12 Diagnost Display Set Up Group Page Entering a Security Code Operator Interface Procedure to Enter a Security Code Key errorIndividual key lockout Monitoring Your Controller 4.4.1 Annunciators AnnunciatorsALM 1 OUT 1 DI 1 Or MAN None, F or C Viewing the operating parameters Lower Display Key Parameter Prompts Diagnostic Messages Diagnostic MessagesDescription Functional Overview Block Diagram of the UDC3200 Controller Configuration check Tuning indicatorsAccutune Procedure for Starting Tune Tune for Simplex OutputsOperation Step Operation Press Result Configuration Check for Duplex Tune for Duplex Heat/Cool Using Automatic Tune at start-up for Duplex Heat/Cool Using Blended Tune at start-up for Duplex Heat/Cool Using Manual Tune at start-up for Duplex Heat/Cool Step Operation Press Result Error Codes 10 Procedure for Accessing Accutune Error Codes11 Accutune Error Codes Aborting Accutune Configuration Fuzzy Overshoot SuppressionHow it works Background Tests Background TestsEE Fail INP1 RNG RV Limit SegerrCAL MTR Curfail Controller Failure Symptoms Other symptoms Sales and Service Page Http//hpsweb.honeywell.com