Kyocera FS-1010 service manual Continue due to complex data

Models: FS-1010

1 172
Download 172 pages 36.88 Kb
Page 121
Image 121

 

Indicator

Remote Operation Panel display

Description

 

 

 

 

 

 

 

 

 

 

 

 

Print overrun

Current print processing cannot

 

 

 

 

 

Press GO

continue due to complex data.

 

 

 

 

 

 

The data transferred to the printer was

 

 

 

 

 

 

too complex to print on a page. Press

 

 

 

 

 

 

 

 

 

 

 

 

the Go key to print data as far as it was

 

 

 

 

 

 

 

 

 

 

 

 

stored. You can abandon printing by the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cancel key.

 

 

 

 

 

 

Note: To release the page protect mode,

 

 

 

 

 

 

send the following command to the

 

 

 

 

 

 

printer from the Remote Operation

 

 

 

 

 

 

Panel utility after this error occurs:

 

 

 

 

 

 

!R! FRPO R5, 1; EXIT;

 

 

 

 

 

 

 

 

 

 

 

 

MemoryCard err##

Check the error code displayed in ##

 

 

 

 

 

Press GO

and refer to the appropriate description

 

 

 

 

 

 

below.

 

 

 

 

 

 

01: Abnormal format. Try turning the

 

 

 

 

 

 

power off and on again.

 

 

 

 

 

 

02: RAM disk mode is Off. Turn RAM

 

 

 

 

 

 

disk mode On.

 

 

 

 

 

 

04: No disk space. Clean up files.

 

 

 

 

 

 

05: Specified file is not on disk.

 

 

 

 

 

 

06: No memory for use by disk system.

 

 

 

 

 

 

Expand printer memory.

 

 

 

 

 

 

(Continued on next page)

 

 

 

 

 

 

 

 

 

 

 

 

MemoryCard err20

The printer has halted because you

 

 

 

 

 

 

attempted to insert/remove a memory

 

 

 

 

 

 

card into/from the printer slot while the

 

 

 

 

 

 

printer power is on.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Turn the power switch off and then on

 

 

 

 

 

 

 

 

 

 

 

 

to restart the printer.

 

 

 

 

 

 

 

 

 

 

 

 

Note: Make sure to turn the printer

 

 

 

 

 

 

power off before inserting/removing a

 

 

 

 

 

 

memory card.

 

 

 

 

 

 

(No indication patterns available)

 

 

 

(No

Format error

This message appears when the printer

indication

MemoryCard

is in the ready state and the memory

patterns

 

card is not formatted, and therefore

available)

 

cannot be read or written.

 

 

 

 

 

 

Format the memory card.

 

 

 

 

 

 

 

FS-1010

6-9

Page 121
Image 121
Kyocera FS-1010 service manual Continue due to complex data