LG Electronics C Series manual Frequency low Limit H14 Skip

Chapter 7. Function list

Function group 2

LED	Parameter	Min/Max		Description	Factory	Adjustable		Page
display	name	range			defaults	during run
H 0	[Jump code]	1/95		This parameter sets the code number to	1	O	5-5
				jump.
H 1	[Fault history	-		ƒ This parameter stores information on the	nOn	-	11-4
	1]			types of faults, the frequency, the current
H 2	[Fault history	-		and the Accel/Decel condition at the time of	nOn	-
	2]			fault.
H 3	[Fault history	-		ƒ The last fault is automatically stored in	nOn	-
	3]			the H 1- [Fault history 1].
H 4	[Fault history	-			nOn	-
	4]
H 5	[Fault history	-			nOn	-
	5]
H 6	[Reset fault	0/1		ƒ This parameter clears the fault history	0	O
	history]			saved in H 1-5.
H 7	[Dwell	F23/400		ƒ When run frequency is issued, motor	5.0	X	10-5
	frequency]	[Hz]		starts to accelerate after dwell frequency is
				applied to the motor during H8- [Dwell time].
				ƒ [Dwell frequency] can be set within the
				range of F21- [Max frequency] and F23-
				[Start frequency].
H 8	[Dwell time]	0/10 [sec]		ƒ This parameter sets the time for dwell	0.0	X
				operation.
H10	[Skip	0/1		ƒ This parameter sets the frequency range	0	X	9-20
	frequency			to skip to prevent undesirable resonance
	select]			and vibration on the structure of the
				machine.
H11	[Skip	0/400		ƒ Run frequency cannot be set within the	10.0	X
1)	frequency low	[Hz]		range of H11 thru H16.
	limit 1]			ƒ The frequency values of the low
H12	[Skip			numbered parameters cannot be set above	15.0	X
	frequency high			those of the high numbered ones.
	limit 1]
H13	[Skip				20.0	X
	frequency low
	limit 2]
H14	[Skip				25.0	X
	frequency high
	limit 2]
H15	[Skip				30.0	X
	frequency low
	limit 3]
H16	[Skip				35.0	X
	frequency high
	limit 3]
H17	S-Curve	1/100 [%]	Set the speed reference value to form a curve		40	X	9-13
	accel/decel			at the start during accel/decel. If it is set
	start side			higher, linear zone gets smaller.
H18	S-Curve	1/100 [%]	Set the speed reference value to form a curve		40	X
	accel/decel			at the end during accel/decel. If it is set
	end side			higher, linear zone gets smaller.
H19	[Output phase	0/1		ƒ Inverter turns off the output when the	0	O	12-5
	loss protection			phase of the inverter output (U, V, W) is not
	select]			properly connected.
H20	[Power On	0/1		ƒ This parameter is activated when drv is	0	O	9-9
	Start select]			set to 1 or 2 (Run/Stop via Control terminal).
				ƒ Motor starts acceleration after AC power
				is applied while FX or RX terminal is ON.
H21	[Restart after	0/1		ƒ This parameter is active when drv is set	0	O
	fault reset]			to 1 or 2 (Run/Stop via Control terminal).
				ƒ Motor accelerates after the fault condition
				is reset while the FX or RX terminal is ON.

47