Liebert XDC user manual Installation data-Lee-Temp, one-circuit, four-fan model

Piping and Filling with Refrigerant: R-134a and R-407c Circuits

Figure 24 Installation data—Lee-Temp, one-circuit, four-fan model

					Field-supplied main disconnect switch in
					accordance with local codes or main unit
					switch ordered as optional equipment
					factory-installed in condenser control box.
					* Liquid line from
					condenser (Circuit 1)
4
6				See
See
				Note 14
Note 12	* Hot Gas Line
	From Unit
	(Circuit 1)
						Electrical service
	Lee-Temp heater					by others
	pad electric box
Mounting Instructions	this end (See Page 3)					Hot Gas Line (Circuit 1)
					See Note 14	Liquid Line (Circuit 1) See Note 14
1. Uncrate carton and inspect for damage to* Hot Gas Line to					Liquid Return	Ensure piping stays below electrical
condenser and condenser control panel. Condenser (Circuit 1)			A			box and does not protrude
				D	Line to Unit
2. Assemble legs per instructions as shown.						Metal
		Position elbow to direct			(Circuit 1)
3. Double risers are required when hot gas		relief valve downward				Clamp
vertical rise is 15 feet (4.6m) or more						Isolator
						Note 14
(see 2.6 Install Double Discharge Risers).
4. Wire according to electrical diagram on inside			MATERIALS SUPPLIED
of condenser control box and in accordance with
			BY EMERSON NETWORK POWER
all local codes.			1 Built-in condenser control box. See electrical drawing￿
5. All condenser locations more than 200ft. (61m) of
				for details and field wiring.
equivalent piping length away from Liebert XDC
must consult factory for special piping considerations.			2	Air-cooled condenser.
6. Field to size refrigerant lines so as not to exceed			3	Piping access cover to be reinstalled when piping is completed.
2°F (1.1°C) saturation loss for total equivalent length			4 Bolts - (4 per leg) 3/8" (9. 5mm) - (16) sixteen 5/8" (15.9mm)
(do not use connection sizes to determine line sizes).
			5	Terminal block for two-wire, 24V interlock connection between￿
7. Condenser installation is limited to a maximum of￿
15ft. (4.6m) location below Liebert XDC unit.				Liebert XDC and Liebert condenser.
8. Do not run piping or wiring in the path of air flow			6	Condenser legs - (8) eight legs for (4) four-fan models.
because this will reduce system performance.			7	Lee-temp:
9. Install field-supplied inverted traps on hot
				a. Insulated storage receiver - storage
gas lines between condenser and field piping.
10. All other piping field-supplied and field-connected.				receiver (1) per circuit. 5-foot-long receiver
11. Inverted traps must be installed to allow proper				is standard.
clearance to fully open condenser control box door				b. Dual head pressure control valve assembly
and in accordance with local electric codes.
				with integral check valve(s) - (1) one per circuit (See Note 13)
12. Secure Lee-Temp receiver assembly and each leg to
condenser frame using hardware provided. Receiver				c. Rotalock valve - (1) one per circuit
can be mounted on either side of the condenser.				d. Pressure relief valve - (1) one per circuit, field-installed.
13. Lee-Temp Item B is shipped as a pre-piped				e. Liquid level indicator - (1) per circuit, factory-installed
assembly shipped loose for field installation.
				on receiver
Item C is shipped loose for field installation.
14. Fasten liquid and hot gas lines using flat surface			8	Bolts - Lee-Temp 3/8" (9. 5mm)
clamps with isolators (field-provided). Support
field piping separately to avoid coil damage and						DPN000937
loss of charge
15. Relieve pressure at access port. Replace access port						Pg. 01, Rev. 09
					For CSL616 condenser piping
fitting with relief valve before charging system.
					connections, see Figures 28 and 29.

24