Manuals / Lowrance electronic / Marine Equipment / Fish Finder

Lowrance electronic LMS-520C, LMS-525C DF manual Advanced Options menu, 220

Models: LMS-525C DF LMS-520C

1 252

Download 252 pages 13.62 Kb

Page 230

Advanced Options menu

The Fuel Flow sensor Advanced Options menu contains two categories: Instance and Restore Defaults.

Instance

The Instance command is intended for use only by experienced NMEA 2000 network technicians. Instance allows network technicians to re- solve certain electronic probe conflicts. This is most likely to occur if the network includes LMF-200 or LMF-400 digital gauges, which support the display of fewer electronic probes than your GPS or sonar/GPS unit. If you want to use your unit in a network including one of these digital gauges, you may need to consult customer service.

You should never need this command if you are connecting your unit to a network with similar display units and/or a series of electronic probes.

Restore Defaults

The Restore Defaults command allows you to reset an individual EP-15 Fluid Level Sensor's settings to factory defaults. If, for example, you execute the Restore Defaults command from your Gray Water Fluid Level Advanced Options menu, only the settings for the Gray Water Fluid Level will be reset to factory defaults. Other fluid levels on the network will not be affected.

To restore default settings:

1.Press MENU MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man- agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn- chronization.

2.Highlight BUS SETUP and press ENT, which will open the Bus Configu- ration menu. A list of network devices will be at the top of the page.

3.Select the desired fluid level and press ENT. The Device Configura- tion menu will appear.

4.Highlight ADVANCED OPTIONS and press ENT.

5.Select RESTORE DEFAULTS and press ENT. The following message will appear: Are you sure you wish to change this device's configuration?

6.Highlight YES and press ENT. Press EXIT repeatedly to get back to the main display.

NOTE:

The Fluid Level Device Configuration menu also contains the Cali- brate button, but we will address that later in the segment covering Calibration.

220

www.Busse-Yachtshop.de email: info@busse-yachtshop.de

Image 230

Lowrance electronic LMS-520C, LMS-525C DF manual Advanced Options menu, 220

Contents

LMS-520C & LMS-525C DF Copyright 2006 Lowrance Electronics, Inc All rights reserved Table of Contents Automatic Sensitivity 121 101105 Advanced GPS Operations 139153 Nmea 2000 Device Configuration 207 193231 Vii Viii Read Me First Page Sonar GeneralBack-up memory LMS-525cDF 50/200 kHzZoom bottom track Sonar soundingAutomatic ranging Surface water tempHow Lowrance Sonar Works Position updatesGraphic symbols for Waypoints or event How Lowrance GPS Works Introduction to GPS and Waas Page Page How to use this manual typographical conventions Arrow KeysInstructions = Menu Sequences Menu CommandsKeyboard Page Transducer Installation PreparationsSelecting a Transducer Location Good and poor transducer locations How low should you go? Shoot-thru-hull vs. Transom MountingTransom Transducer Assembly And Mounting Assembling the bracketAligning the transducer on the transom Insert bolt and check transducer position on transom Assembling the transducer Drilling mounting holesAttaching transducer to transom Bottom Hull Flat-bottom hullDeep-vee hull Trolling Motor Bracket Installation single-frequency only Transducer Orientation and Fish ArchesShoot-Thru-Hull Preparation Testing Determines Best Location True bottom Second bottom Manual range setting Shoot-thru-hull Installation Speed/Temperature Sensors Optional Speed Sensor InstallationGood location Power Connections Powering Your Display Unit Failure to use a 3-amp fuse will void your warrantyPower Diagram a Power Diagram B Powering a Nmea 2000 Network BusGPS Antenna/Receiver Module Connecting to a Nmea 2000 Network Nmea 0183 Wiring Data cable Page LMS-520c and LMS-525cDF cable connections Bracket Installation Mounting the Unit Bracket, In-Dash or PortableFront In-Dash Installation Template4.46MMC or SD Card Memory Card Installation Portable InstallationTo remove an MMC To add an MMC or SD CardOther Accessories Cleaning TowelFace Cover Page Basic Sonar Operation KeyboardPower/lights on and off Main MenuMain Menu Pages Satellite StatusNavigation MapSonar Page Sonar Page showing full sonar chart mode Basic Sonar Quick Reference Sonar Operations To adjust sensitivity Fish Symbols vs. Full Sonar Chart Important TipOther Free Training Aids Page ASP Advanced Signal Processing To change the ASP levelAlarms Depth AlarmsZone Alarm Fish Alarm GPS Alarms Nmea 2000 Alarms Important Alarm NotesCalibrate Speed TipChart Speed To change chart speed ColorlineCursor To adjust Colorline levelDepth Cursor Depth Range Automatic Depth Range ManualDepth Range Upper and Lower Limits To change the upper and lower limitsFasTrack To turn off upper and lower limitsFish I.D. Fish Symbols & Depths Page Frequency Change Transducer Frequency LMS-525cDF only To turn the Fish I.D. feature onFishTrack To turn on FishTrackHyperScroll To change the frequency setting to 50 kHzTo change the frequency setting to 200 kHz Log Sonar Chart Data To record or log chart dataTo overlay information on your screen Noise RejectionOverlay Data Data Viewer menu left. Sonar Data category expanded right To remove overlaid data To move overlaid dataPing Speed & HyperScroll To turn off HyperScroll Reset OptionsTo change Ping Speed Reset Water Distance Set Keel OffsetSensitivity & Auto Sensitivity To adjust sensitivity in auto mode Automatic SensitivityTo turn Auto Sensitivity back on Sonar Chart ModeTo adjust sensitivity in manual mode Full Sonar Chart Sonar Page & Sonar Chart Display OptionsTo change the chart mode color scheme+ Split Zoom Sonar Chart Split Frequency Sonar Chart LMS-525cDF onlyDigital Data/Chart Customize Page DisplaysTo change the information displayed in a data box Sonar with Custom Gauges FlasherTo customize digital gauge display To resize Sonar and Custom Gauge windows Map with Sonar Split ScreenSonar Simulator To use the simulatorPress ↓ ↑ to file nameENT↓ to Playentexit Stop Chart To adjust the Surface Clarity level Surface ClarityTo adjust Menu Transparency level TransparencyZoom Pan Upper and Lower LimitsZoom & Zoom Bar 100101 Unit wont turn onUnit freezes, locks up, or operates erratically No fish arches when the Fish I.D. feature is off 102103 104 Basic GPS Operations 105106 107 108 To set up Custom Gauge 109110 111 112 Navigation113 Background map vs. MapCreate map content 114115 116 117 Map with SonarTo resize Map with Sonar windows Map with Custom Gauges 118Radar 119To access Radar 120Basic GPS Quick Reference 121122 Find Your Current PositionMoving Around the Map Zoom & Cursor Arrow Keys 123 Selecting Any Map Item with the CursorSearching After the unit has acquired a position 124125 Set a WaypointTo create and save a Waypoint 126 127 Navigate To a WaypointSet Man Overboard MOB Waypoint 128 Navigate Back to MOB WaypointNavigate to Cursor Position on Map 129 130 Navigate to a Point of InterestCreating and Saving a Trail To Save a Trail 131132 Displaying a Saved TrailTo turn off trail display Visual Trailing Navigating TrailsTo turn on trail display Navigate a TrailSure press ←ENT.Figure 134Navigate a Back Trail backtrack 135GPS Data files Transfer Custom Maps and GPS Data FilesCustom Maps 136137 Cancel Navigation 138139 Find Distance from different LocationsFind Distance from Point to Point Create Icon at Current Position IconsCreate Icon on Map Delete an Icon141 RoutesNavigate to an Icon Create and Save a Route 142143 Delete a Route 144145 Edit a Route NameEdit Route Waypoints 146 Navigate a RouteNavigate a Route in Reverse 147 TrailsDelete a Trail Edit a Trail Pattern Edit a Trail NameEdit a Trail Color 148Utilities WaypointsTo delete all waypoints at one time To edit waypoint symbolTo delete a waypoint from the map Edit a Waypoint To edit waypoint name151 152 Set a Waypoint by Average PositionSet a Waypoint by Projecting a Position To change alarm settings 153Auto Satellite Search 154155 Communications Port ConfigurationCheck MMC Files and Storage Space To get to Coordinate System Selection Configure NmeaCoordinate System Selection 156To set up Loran TD 157158 To configure a map fixMap Fix 159 Customize Page DisplaysTo change data box information 160 GPS SimulatorTo turn on the GPS Simulator Steer with Arrows 161Initialize GPS Hide GPS FeatureTo Hide GPS Features Simulating Trail or Route NavigationTo Initialize GPS Map Auto ZoomMap Data To turn on Auto ZoomTo turn on/off Pop-up Map Information To access Map Data menuTo show Map Data To turn on/off Draw Map BoundariesTo turn on/off range rings Map Datum SelectionMap Overlays Range Rings Lat/Long Grid To turn on/off Lat/Long Grid lines166 Map Detail Category SelectionMap Orientation 167 168 NauticPath USA Marine ChartsNautical Chart Notes Port Information To view Chart Note informationTo view Port Services information 169Tidal Current Information 170To view Tidal Current information 171172 To select another dateTide Information 173 Navionics→ ChartsTo view tide information To display a Navionics chart 174175 176 177 178 To set up Popup HelpPop-up Help 179 Screen Contrast and Brightness 180Set Local Time To adjust the screens display modeSet Language To set the MonthTo set the Year Show Waas AlarmTo Configure DST To select Time FormatSoftware Version Information To turn on/off the Waas AlarmTo access Software Information To Require WaasTo set Volume Sounds and Alarm Sound StylesTo set Alarm Sounds To set Alarm Style185 Track SmoothingTrail Options To Delete all Trails Update Trail OptionTo create a New Trail 186187 188 To delete a TrailTrail Visible/Invisible and Other Trail Options To change Units of Measure To set Speed/Distance To adjust Transparency levelUnits of Measure 189To set Depth units To set Temperature unitsTo set Pressure units 190191 To set Volume unitsTo set Heading units 192 Searching 193Find Streets 194195 Find Any Item Selected by Map CursorFind Interstate Highway Exits 196 197 Find Map Places or Points of Interest POI 198199 200 Find Streets or IntersectionsFind a Street Find an Intersection 201202 Find Waypoints 203204 205 206 207 Bus SetupNmea 2000 Menu Engine & Tank Configuration 208Setting Engine-Tank Configuration 209210 Device Configuration MenuDevice Information and Device Data Fuel Management Menu 211If you did not fill up the tank Adding Fuel to TankIf you filled up the tank Engine Operations213 214 Waypoint SharingBacklight Synchronization 215 Configuring EP SensorsEP-35 Temperature Configuration 216 EP-10 Fuel Flow ConfigurationAdvanced Options menu 217 EP-15 Fluid Level Configuration 218219 220 Suzuki Engine Interface Configuration 221222 223 Calibrating EP SensorsEP-10 Fuel Flow Calibration EP-15 Fluid Level Calibration 224225 226 Fuel Flow Calibration in a Suzuki Engine Interface 227228 Engine connected to your engine interfaceEngine Trim Calibration 229 Reset Trim CalibrationBennett Trim Tabs Calibration 230 Supplemental Material Datums Used by This Unit 231232 233 Conus234 FCC Compliance 235236 Lowrance Databases License Agreement 237Databases Limited Warranty 238Lowrance Electronics Full ONE-YEAR Warranty 239Not toll-free 240Accessory Ordering Information for all countries Visit our web site