Mocomtech CRS-300 operation manual No Error

CRS-300 1:10 Redundancy Switch	Revision 16
Front Panel Operation	MN/CRS300.IOM

The three-letter instruction code is indicated also to assist decoding the following problem parameters:

►For the CDM-600L modem, the code is the hex value of the position of the problem parameter within the MGC configuration code.

00		NO ERROR
09	TDR	Tx Data Rate
13	TRS	Tx Reed Solomon type
15	TMD	Tx Modulation
17	TSC	Tx Scrambler state
1C	AUP	AUPC enable
23	TCK	Tx Clock source
25	TIT	Tx Interface Type
27	TFM	Tx Framing Mode
29	RFQ	Rx Frequency
3A	RFT	Rx FEC Type
3C	RCR	Rx FEC Code Rate
3E	RSI	Rx Spectrum Inversion
40	RSW	Rx Sweep Width
43	EBA	EbNo Alarm point
4C	RIT	Rx Interface Type
4E	RFM	Rx Framing Mode
50	EFM	Unit EDMAC Mode
55	TST	Unit Test Mode
5C	EFR	External Freq Ref
5E	RTE	Rx Terrestrial Alarm Enable
60	ODU	ODU comms Enable
65	RBA	Rx Backward Alarms
6D	RVL	Rx audio Volume
72	ITY	Insert Type
74	RET	Rx ESC Type - 64k or 2 audio
76	IRD	Invert Rx Data

01	TFQ	Tx Frequency
12	TFT	Tx FEC Type
14	TCR	Tx FEC Code Rate
16	TSI	Tx Spectrum Inversion
18	TPL	Tx Power Level
1D	APP	AUPC parameters
24	TXO	Tx Carrier state
26	TTC	Tx Ternary Code
28	TIP	Tx IF Impedance
31	RDR	Rx Data Rate
3B	RRS	Rx Reed Solomon type
3D	RMD	Rx Modulation
3F	RDS	Rx DeScrambler state
42	RCK	Rx Clock source
47	RBS	Rx Buffer Size
4D	RTC	Rx Ternary Code
4F	RIP	Rx IF Impedance
51	ESA	EDMAC Slave Address
56	MSK	Unit Alarm Mask
5D	SSI	Statistics Sampling Interval
5F	TTA	Tx Terrestrial Alarm Mask
61	TBA	Tx Backward Alarms
69	TVL	Tx audio Volume
71	DTY	Drop Type
73	TET	Tx ESC Type - 64k or 2 audio
75	ITD	Invert Tx Data

►For the CDM-570L modem, the code is the decimal number indicating the problem parameter within its MGC configuration code:

00		NO ERROR	01	ITF	Interface
02	LBO	T1 Line Build-Out	03	FRM	Framing mode
04	TFQ	Tx Frequency	05	TFT	Tx FEC Type
06	TMD	Tx Modulation	07	TCR	Tx FEC Code Rate
08	TDR	Tx Data Rate	09	TSI	Tx Spectrum Invert
10	TSC	Tx Scrambler state	11	TPL	Tx Power Level
12	TCK	Tx Clock	13	TDI	Tx Data Invert
14	TXO	Tx Carrier State	15	AUP	AUPC enable
16	APP	AUPC parameters	17	WUD	Warm-Up Delay
18	RFQ	Rx Frequency	19	RFT	Rx FEC Type
20	RMD	Rx Modulation	21	RCR	Rx FEC Code Rate
22	RDR	Rx Data Rate	23	RSI	Rx Spectrum Invert
24	RDS	Rx DeScrambler state	25	RDI	Rx Data Invert
26	RSW	Rx Sweep Width	27	EBA	Eb/No Alarm point
28	RBS	Rx Buffer Size/enable	29	ERF	External Reference setting
30	EFM	EDMAC Framing mode	31	ESA	EDMAC Slave Address range
32	TST	Test mode	33	MSK	Alarm Masks
34	RTS	Request-To-Send control	35	SSI	Statistics Sample Interval

7–16