Blacklist Full | Multi-Tech Systems MT5634MSV guide

MessageSaver User Guide

Terse		Verbose	Description
90		BLACKLIST FULL	Blacklist is full
100	*	CONNECT 28000	Connected at 28000 bps, 56K rate (V.90)
101	*	CONNECT 29333	Connected at 29333 bps, 56K rate (V.90)
102	*	CONNECT 30666	Connected at 30666 bps, 56K rate (V.90)
103	*	CONNECT 33333	Connected at 33333 bps, 56K rate (V.90)
104	*	CONNECT 34666	Connected at 34666 bps, 56K rate (V.90)
105	*	CONNECT 37333	Connected at 37333 bps, 56K rate (V.90)
106	*	CONNECT 38666	Connected at 38666 bps, 56K rate (V.90)
107	*	CONNECT 41333	Connected at 41333 bps, 56K rate (V.90)
108	*	CONNECT 42666	Connected at 42666 bps, 56K rate (V.90)
109	*	CONNECT 45333	Connected at 45333 bps, 56K rate (V.90)
110	*	CONNECT 46666	Connected at 46666 bps, 56K rate (V.90)
111	*	CONNECT 49333	Connected at 49333 bps, 56K rate (V.90)
112	*	CONNECT 50666	Connected at 50666 bps, 56K rate (V.90)
113	*	CONNECT 53333	Connected at 53333 bps, 56K rate (V.90)
114	*	CONNECT 54666	Connected at 54666 bps, 56K rate (V.90)

*EC is added to these result codes when the extended result codes configuration option is enabled. EC is re- placed by one of the following codes, depending on the type of error control connection:

V42bis —V.42 error control (LAP-M) and V.42bis data compression

V42 —V.42 error control (LAP-M) only

MNP5 —MNP 4 error control and MNP 5 data compression

MNP4 —MNP 4 error control only

NoEC —No error control protocol).

46

Image 54

Multi-Tech Systems MT5634MSV manual Blacklist Full

Contents

User Guide FCC Part User Guide Record of Revisions Introduction Quick StartMessageSaver Operation Solving Problems AT Commands, S-Registers & Result CodesRemote Configuration PhoneTools Appendix a Regulatory Compliance Appendix C Loopback Tests Appendix D Warranty, Service, and Technical Support Appendix E Upgrade Procedures Introduction Introduction Product Description What Is in Your Modem Package? How to Get a Copy of Your User Guide Related Manuals MessageSaver User Guide Quick Start What You Will Need Safety WarningsIntroduction We supply Mount the Feet Select Stereo or Mono SpeakerOpening the Modem Changing the Speaker Jumper Location of speaker jumper Connect the Modem to Your System RS232 ConnectionLine Connection Phone Connection Power ConnectionPower-On Test Microphone Connection Install the Modem in Windows Adding the Modem to WindowsRemoving Your Old Modem from Windows Install and Configure Your Software Call the Multi-Tech BBS Windows HyperTerminal Windows Terminal Send a Fax Microsoft Fax Select Start Programs Accessories Fax Compose new fax References MessageSaver User Guide MessageSaver Operation PhoneTools Features Independent Mode Functions Recording and Downloading an Announcement MessageSaver Operation Independent Mode Operation in PhoneTools Independent Mode Configuration Dialog Box Independent Mode Control Dialog Box Independent Mode Control dialog box Independent Mode Operation Using the Front Panel Control Buttons Indicator Lights Playing Voice Messages Adjusting Speaker VolumeAnswering a Call with the Speakerphone Stopping the Play of Voice Messages Remote Control Using the MessageSaver in Speakerphone ModeControlling the MessageSaver Remotely Activating Independent Mode Remotely Remote Control Keys AT Commands Registers Result Codes AT Commands AT Command Summary Echo Online Data Characters Echo Command Mode CharactersDS=y Dial Stored Telephone Number Hook Control Return Online to Data Mode Monitor Speaker VolumeMonitor Speaker Mode Modulation Handshake Sr? Read Register Value Result Codes Enable/DisableSet Register Value Tone Dialing Auto Retrain Modem ResetLong Space Disconnect Data Carrier Detect DCD Control Asynchronous Communications Mode Load Factory SettingsCommunications Mode 22bis Guard Tone Control Store Current Configuration Test CommandsDisplay Current Settings Select Stored Configuration for Hard Reset \Gn Modem Port Flow Control \An\Bn Transmit Break \Jn Data Buffer Control \Nn Error Correction Mode Selection \Tn Inactivity Timer\Qn Flow Control Selection \Xn XON/XOFF Pass-Through DCn AT Command Control\Vn Protocol Result Code Data Calling Tone #S=x Store Setup Password Command +ES=n Enable Synchronous Buffered Mode#Sx Enter Setup Password Command +++ATCR Escape Sequence Register Unit Range Default Description Registers Register Unit Range Default Description S37 Register Unit Range Default Description S42 Result Codes Terse Verbose Description Blacklist Full Remote Configuration Basic Procedure SetupChanging the Setup Password Changing the Remote Escape Character MessageSaver User Guide Solving Problems None of the Indicators Light Modem Does Not Respond to Commands Modem Dials But Cannot Connect Modem4Disconnects While Online Modem4Cannot Connect When Answering File Transfer4Is Slower Than It Should BeData Is Being Lost There Are Garbage4 Characters on the Monitor Modem4Doesn’t Work with Caller IDFax and Data4Software Can’t Run at the Same Time MessageSaver User Guide PhoneTools Installing PhoneTools Using PhoneTools’ Status Bar Phone ModuleMaking a Phone Call Using the Speakerphone Making Quick Dial Entries Setting up Answerphone Voice ModuleActivating and Deactivating Answerphone Setting Up the Answer Only Mode Setting Up the Answer/Record Mode Listening to Received Messages from a Remote Phone Listening to Received Messages in PhoneTools Recording an Announcement Changing Recording Parameters Independent Mode Configuring and Controlling Independent Mode OperationHow Does It Work? Activating and Configuring Independent Mode Selecting an Announcement Independent Mode Managing Stored Documents Inbox Fax Module Faxing a Document from a Windows Application Faxing a File Directly from PhoneTools Sending a Cover Adding a Logo to the Cover Viewing and Printing Faxes Inbox and Outbox Management Inbox Management Outbox Management Importing Existing Records Phone BookCreating New Records Selecting Records Using the Phone Book for Dialing Terminal Emulation Module Starting a Modem Connection Uploading Files to a Remote System Capturing Information to Disk Data File Transfer Sending a Data File Automatically Receiving a Data File Automatically Appendixes Appendix a Regulatory Compliance FCC Part 68 Telecom Fax Branding Statement Regulatory Compliance Canadian Limitations Notice International Modem RestrictionsCommission Decision CTR21 EMC and Safety Compliance New Zealand Telecom Warning Notice MessageSaver User Guide Appendix B Technical Specifications Carrier Frequencies Frequency Stability MessageSaver User Guide Test procedure Local Analog Loopback Test V.54 Loop Remote Digital Loopback Test V.54 Loop Figure C-2. Remote digital loopback test Local Digital Loopback Test V.54 Loop Figure C-3. Local digital loopback test MessageSaver User Guide Limited Warranty Service Online Warranty Registration Technical SupportMulti-Tech BBS About the Internet Modem Accessories About the Multi-Tech Fax-Back ServiceSupplyNet Online Ordering Instructions Upgrade Overview Identify the Modem Firmware Identify the Current Firmware Version Multi-Tech Web SiteMulti-Tech BBS Download the Upgrade File Extract the Upgrade FilesClear Your Stored Paramenters Upgrade the Modem’s Firmware Restore Your Parameters Index Symbols Index 106