Kit Name Kit Type Available for | NCR 7870 specs

2-14 Chapter 2: Features, Functions, and Kits

Kit Name	Kit Type	Available for

RS-232 Interface (Board,	Hardware,	All
Firmware)	Firmware
7870-K452-V003

Requirements: V001 supports units with S/Ns 50-28901727 or lower. V002 supports units with S/Ns 50-00000000 and higher. V003 enhances the old digital board firmware.

Datachecker, 2170, ICL MDL,	Hardware,	All
ICL 9518/9535, SASI Interface	Firmware
7870-K455-V001, -V002, -V003

Requirements: Kit is for interfacing with these host terminals: NCR 2170 (RS-232, Weightronix Emulation), Avery Emulation (RS-232), Datachecker (RS-422), ICL MDL, ICL 9518, ICL 9535 (ICL Team POS 5000), SASI.

V001 supports only ICL T2001, V002 supports units with S/Ns 50- 28901727 or lower. V003 supports units with S/Ns 50-00000000 and higher.

Non NCR OCIA	Hardware,	All
7870-K457-V002	Firmware

Requirements: V001 supports units with S/Ns 50-28901727 or lower.

V002 supports units with S/Ns 50-00000000 and higher.

Casio and TEC Scale Interface	Hardware,	7870-2000
7870-K458-V003	Firmware

Requirements: V001 supports units with S/Ns 50-28901727 or lower. V002 supports units with S/Ns 50-00000000 and higher. V003 supports the same as V002 plus TEC.

Image 38

NCR 7870 manual Kit Name Kit Type Available for

Contents

Users Guide Page Table of Contents Site Preparation Users Guide Installation Calibration Operation Programming Users Guide Viii Users Guide Troubleshooting Appendix a Programming Worksheets Revision Record Canadian Department of Communications Radio Frequency Interference StatementsFederal Communications Commission FCC Voluntary Control Council For Interference Vcci Mark Applicability Scale Regulatory Declaration of Conformity This Directive is not applicable to NCR 7870-1000 or NCR Scale Identification Label NCR Corporation Laser Safety Laser Safety Label Country Language Specific IEC Class 1 Laser Labels Laser Power Laser Module Label Microwatts Milliwatts Introduction About the NCR 7870 Scanner/Scale Models Common Features Reading the Product Number 7870-3000-9090 7870-1000-90907870-2000-9090 7870-4000-9090 General Features and Functions Bar Code Recognition Bi-Optic Scanning Decode FeaturesMode 1 Inquiry Mode Pacesetter Plus Displays Mode 2 Real-Time ModeMode 3 Operations Mode NCR 7825 Remote Display Integrated Display Laser Scanner Power SupplyInterface Types No Display Programming Sizes section in Site Preparation Scale Certifications Scan Zone Scanner Power RequirementsSoft Power Down Slot Scanner Window Top Plates and Scan WindowsTop Plates Side Scanner Window Reset / Scale Zero Scale Features and FunctionsScale Functions and Features Load Cell Kits Kit Name Kit Type Available for Kit Name Kit Type Available for Kit Name Kit Type Available for Chapter Kit Name Kit Type Available for Kit Name Kit Type Available for Features, Functions, and Kits Site Preparation Getting Started Site Preparation About Site Preparation Site Preparation Customer Responsibilities Extreme Operating Range Environmental RequirementsOperating Range Storage Range Transit Range Power Applications Checkstand Power and Wiring ConsiderationsPower Considerations Power Transients Protection Wiring Considerations Canadian, and Japanese Checkstand Wiring European Checkstand Wiring 220Vac Store International Checkstand Wiring Circuit a Wiring InstructionsRunning Feeder Lines from Main Service Panel Circuit B Circuit C Checkstand Considerations Ventilation Requirements Service Clearance Display Clearance Item Diverter Checkstand Hole Checkstand Hole Models 1000 NCR 7870-1000 Scanner Checkstand Hole Models 3000, 4000 NCR 7870 3000 Scanner Cable Hole Diameters DC Power Cable Power Supply toCable Lengths and Hole Sizes Minimum Hole Diameter 1.52 cm 0.60 Minimum Hole Diameter 3.18 cm 1.25 AC Power Cords Outlet to Power SupplyRemote Display Cables Minimum Hole Diameter 1.90 cm 0.75 Interface Cables NCR Host Terminals Host Interface Cable Corporate Part Length Terminal Number Interface Cables NCR Host Terminals Interface Cables Casio Host Terminals Interface Cables Gilbarco Host Terminals Interface Cables Data Checker Host TerminalsInterface Cables Epson Host Terminals Interface Cables IBM Host Terminals Interface Cables ICL Host Terminals Interface Cables Microbilt Host Terminals Interface Cables NEC Host Terminals Interface Cables Sasi Host Terminals NCR 7870 2000 Dimensions NCR 7870 DimensionsNCR 7870 1000 Dimensions NCR 7870-1000 & 2000 Models NCR 7870 3000 Dimensions NCR 7870-3000 Model NCR 7870 4000 & 4500 Dimensions NCR 7870-4000 & 4500 Models Reporting a Damaged Unit What’s in the Box Cable Verification Checkstand Verification Instructions Installing Unit in CheckstandInstall Cables Single Cable Set-Up Dual Cable Set-Up Datachecker or RS-232 Cable Set-Up Tower Subplate Assembly Cover/Lift Strap NCR 7870-1000 and 3000 Scanners If the NCR 7870 Does Not Pass Level O DiagnosticsDetermining if the Unit is Operational NCR 7875-2000, 4000, and 4500 Scanner/Scales Checkout Reading Operation Determining Communications Protocol Scale Address for IBM Installation Calibration General Calibration Tools Calibration ProcedureExercising the Scale Instructions Accessing the Calibration Switch Remove screw securing Lift Strap to unit 11040 Connecting the Field Service Calibration Display Go to Performing the Calibration Performing the Calibration Display Add Weight Remove Weight Verifying Calibration Procedure 1 Increasing Load Test Select the appropriate weight feature from the table below Procedure 2 Over-Capacity Test Procedure 3 Decreasing Load Test Procedure 4 Shift Test Securing the Calibration Switch Prior Steps Calibration Calibration Operation Scan Windows About Using the Operator ControlsStatus Indicators Audible Tone Reset / Scale Zero ButtonMotion Detector Voice Messages About Using the Scanner Proper Label Orientation Active Scan Zone Multiple Reads Bar Code Quality Scanner Only Models Power UpOperating Instructions Scanner/Scale Models Scanning Procedure Not-On-File Error Weighing Procedure Changing the Good Read Tone Routine Maintenance Operation Programming Programming Writing the Program How to Program the NCRCreating the Program Entering the Program Scan the Save and Reset Tag Save the Program Programming Mode NormalNormalOperatingOperatingModeMode Programming Tags Abort Hex 0 Hex F DefaultEnd Function Programming Mode Save and Reset Enter All Parameters Scan the Programming Mode tagProgram Entry Example Enter Specific Parameters Base Programming State Ar C odes Code Programming Tips Communications Protocol DefaultsProgram Parameter Descriptions Specific Program Parameters IBM 468x/9x Port 4A Slot Scanner Hex 3 tag Ocia NCR Long HexOcia Non NCR Dual Cable Hex Ocia Single Cable Hex 6 tag IBM 468x/9x Port 4B Hhbcr Hex 4 tagRS-232 Hex 5 tag Ocia NCR Dual Cable Hex 7 tag TEC, 4-Bit, Parallel, Dual Cable Hex C tag Casio 4-Bit, Parallel, Dual Cable Hex a tagIBM 1520 BRC, IBM 468x/9x Port 4B Hex B tag Your Program Programming ExampleCommunications Protocol Hex Tag Summary Tone Frequency Hertz Not On File Tone VolumeGood Read Tone Tone Length Milliseconds Tone VolumeProgram Example Tone On/Off Restart Lockout Timer TimersLockout Timer Milliseconds Active Time Minutes Bar Codes Version D Periodic Codes Extend UPC-A to EAN-13Extend UPC-E to UPC-A Periodic Code Extension 0 0 1 2 Send Data Code Minimum Characters Allowed Transmit Check Digit Full AsciiCheck Digit Present Allow 1- or 2-Character Tags Ascii Interleaved 2 Bar Code Length Value 1 4 1 0 Minimum Data Characters Allowed UCC Bar Codes Minimum Data Characters Allowed UCC Label Identifiers Identifier Type Common Byte 1 and Common Byte Unique Identifier Bar Code TypeCommon Byte Version Number UPC-D Only Label Identifier Parity RS-232 ParametersBaud Rate Stop Bits and Character Length Handshake RS-232 Parameters Baud Rate Parity BCC Options Interface Control Check Digit RS-232 Parameters BCC Interface Options Control Check Digit Ascii Code RS-232 Prefix BytePrefix Byte RS-232 Prefix Byte RS-232 Terminator Byte Terminator Byte RS-232 Terminator Byte RS-232 Communications Options Normal or Eavesdrop ModeMessage Delay Scanner or Scanner/Scale Format Beep at Scale Weight Transmission RS-232 IBM Address Scale ParametersModel Number 995 kg / 13.995 kg Second Weight Display Timer Miscellaneous Parameters Ocia Price Display Ocia Blank Display In Price ModeIBM Tone Control Good Read Tone IBM Rexmit Control Enable/Disable Voice Messages IBM Tag Data Format 11822 Mode 1 Inquiry Pacesetter Plus Information Mode 2 Real Time 1136 Codes Description Mode 3 Normal OCH, xyH, xzH 43H, 3yH, 3zH OCH, 0yH, 0zH Decoding was difficult. May be due to Example Host Access to TalliesExamples of Host Access to Tallies An IBM host terminal request for tally C1 0DH C1H Host Reset of Tallies C5H C0H Delay Weight Data to IBM Host Terminal Special Programming Single Label Restriction EAN/JAN/UPC Multi-Symbol Scanning ParametersLabel Construction Transmitting Label Data Hex a tag and the Save and Reset tag Programming Early Beep Disable Good Read Tone Presets Preset Good Weigh Tone When Transmitting Data Hex a Hex B Terminal Coupon Interface ParametersHex Hex C Hex D Coupon Select 2 Parameter Disable Enable Ascii Code Chart 1A SUB 1B ESC 1C FS 1D GS 1E RS 1F US Programming Troubleshooting Fault Identification Scanner Troubleshooting Chart Scale Troubleshooting Chart Scan Programming Mode tag Voice Messages Troubleshooting ChartScan the Diagnostic Mode tag Troubleshooting Shortcuts PurposeFormat Program Entry DefaultsHex Characters Good Read Tone TimersCommunications Protocol Bar Codes-1 Label Identifiers Bar Codes-3Bar Codes-4 RS-232 Parameters-1 RS-232 Communications Options RS-232 Prefix ByteRS-232 Terminator Byte Scale Parameters Worksheets Communications Protocol Good Read Tone Timers BAR Codes BAR Codes BAR Codes Code Label Identifiers RS-232 Parameters Appendix a Programming Worksheets A-15 RS-232 Prefix Byte RS-232 Terminator Byte RS-232 Communications Options Scale Parameters Miscellaneous Parameters Appendix a Programming Worksheets A-21 Appendix a Programming Worksheets Index Scanner/Scale Index-3 Slot Scan Window Index-5 Business Reply Mail BST0-2121-90 Nov Printed on recycled paper